FVP PREMIUM ATF QUART Not available. Liquid. INFOTRAC 1-800-535-5053 SAFETY DATA SHEET GHS product identifier Other means of identification Product type Emergency telephone number Section 1. Identification : : : : Supplier's details : Factory Motor Parts 1380 Corporate Center Curve, Suite 200 Eagan, MN 55121 866-387-3343 FVP PREMIUM ATF QUART Relevant identified uses of the substance or mixture and uses advised against Identified uses None known. Uses advised against Reason Product code : 301163640125 Hydraulic oil Section 2. Hazards identification AQUATIC HAZARD (ACUTE) - Category 2 AQUATIC HAZARD (LONG-TERM) - Category 2 Classification of the substance or mixture : Signal word : Hazard statements : Toxic to aquatic life with long lasting effects. Hazard pictograms : Precautionary statements Prevention : Avoid release to the environment. Response : Collect spillage. Storage : Not applicable. Disposal : Dispose of contents and container in accordance with all local, regional, national and international regulations. GHS label elements Percentage of the mixture consisting of ingredient(s) of unknown hazards to the aquatic environment: 100% General : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and available for employees and other users of this product. Hazards not otherwise classified : None known. No signal word. Date of issue/Date of revision : 11/11/2024 Version : 4 1/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 3. Composition/information on ingredients Other means of identification : Not available. Substance/mixture : Mixture Note L: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 3 % DMSO extract as measured by IP 346 ?Determination of polycyclic aromatics in unused lubricating base oils and asphaltene free petroleum fractions ? Dimethyl sulphoxide extraction refractive index method?, Institute of Petroleum, London. This note applies only to certain complex oilderived substances in Part 3. Ingredient name CAS number% There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Occupational exposure limits, if available, are listed in Section 8. Any concentration shown as a range is to protect confidentiality or is due to batch variation. Distillates (petroleum), hydrotreated heavy paraffinic ?90 64742-54-7 Distillates (petroleum), hydrotreated light paraffinic ?3 64742-55-8 Distillates (petroleum), solvent-dewaxed light paraffinic ?3 64742-56-9 Distillates (petroleum), solvent-dewaxed heavy paraffinic ?3 64742-65-0 1-(tert-dodecylthio)propan-2-ol <1 67124-09-8 Alkyl Phosphites <1 Trd Secret Wash out mouth with water. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion : : : : Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Description of necessary first aid measures Specific treatments : No specific treatment. Most important symptoms/effects, acute and delayed Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact Over-exposure signs/symptoms Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Potential acute health effects Indication of immediate medical attention and special treatment needed, if necessary Date of issue/Date of revision : 11/11/2024 Version : 4 2/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 4. First aid measures Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. See toxicological information (Section 11) Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide In a fire or if heated, a pressure increase will occur and the container may burst. This material is toxic to aquatic life with long lasting effects. Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters Use an extinguishing agent suitable for the surrounding fire. Extinguishing media : : : Do not use water jet. Suitable extinguishing media : Unsuitable extinguishing media : Special protective actions for fire-fighters : Section 6. Accidental release measures Environmental precautions Personal precautions, protective equipment and emergency procedures Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. : : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Put on appropriate personal protective equipment. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities. Collect spillage. Large spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up For non-emergency personnel For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Date of issue/Date of revision : 11/11/2024 Version : 4 3/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : : Protective measures Put on appropriate personal protective equipment (see Section 8). Do not ingest. Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Avoid release to the environment. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. : Precautions for safe handling Section 8. Exposure controls/personal protection Control parameters Distillates (petroleum), hydrotreated heavy paraffinic ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), hydrotreated light paraffinic ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed light paraffinic ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist Ingredient name Exposure limits Occupational exposure limits Date of issue/Date of revision : 11/11/2024 Version : 4 4/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 8. Exposure controls/personal protection Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side- shields. Eye/face protection Respiratory protection : : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. : Environmental exposure controls : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate engineering controls : Good general ventilation should be sufficient to control worker exposure to airborne contaminants. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed heavy paraffinic ACGIH TLV (United States, 1/2023). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist 1-(tert-dodecylthio)propan-2-ol None. Alkyl Phosphites ACGIH TLV (United States). TWA: 5 mg/m?, (Mist) STEL: 10 mg/m?, (Mist) Biological exposure indices No exposure indices known. Date of issue/Date of revision : 11/11/2024 Version : 4 5/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 9. Physical and chemical properties and safety characteristics Physical state Melting point/freezing point Vapor pressure Relative density Relative vapor density Liquid. Not available. 0.8494 Not available. Petroleum [Slight]Odor pH Red.Color Evaporation rate Not available. Auto-ignition temperature Flash point Not available. Closed cup: 202?C (395.6?F) [ASTM D 93] Not applicable. Not available. Viscosity Kinematic (40?C (104?F)): 37.9 mm2/s (37.9 cSt) Not available.Odor threshold Partition coefficient: n- octanol/water : : : : : : : : : : : : : : Appearance Boiling point, initial boiling point, and boiling range : Not available. Flammability : Not available. Lower and upper explosion limit/flammability limit : Not available. Decomposition temperature : Not available. Solubility in water : Not available. Flow time (ISO 2431) : Not available. Particle characteristics Median particle size : Not applicable. The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Ingredient name Vapor Pressure at 20?C Vapor pressure at 50?C mm Hg kPa Method mm Hg kPa Method Distillates (petroleum), hydrotreated heavy paraffinic <0.07501 <0.01 ASTM D 5191 Pour point : -54?C (-65.2?F) Solubility(ies) : Media Result cold water Not soluble hot water Not soluble Section 10. Stability and reactivity Conditions to avoid No specific data. The product is stable.Chemical stability No specific data. : : Incompatible materials : Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity : No specific test data related to reactivity available for this product or its ingredients. Date of issue/Date of revision : 11/11/2024 Version : 4 6/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 10. Stability and reactivity Hazardous decomposition products Under normal conditions of storage and use, hazardous decomposition products should not be produced. : Section 11. Toxicological information Acute toxicity Distillates (petroleum), hydrotreated heavy paraffinic LC50 Inhalation Dusts and mists Rat 5.7 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), hydrotreated light paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed light paraffinic LD50 Dermal Rabbit >5000 mg/kg - LD50 Dermal Rat >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed heavy paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - 1-(tert-dodecylthio)propan- 2-ol LD50 Oral Rat >5 g/kg - Alkyl Phosphites LD50 Dermal Rabbit >500 mg/kg - LD50 Oral Rat >2000 mg/kg - Product/ingredient name Result Species Dose Exposure Carcinogenicity Not available. Mutagenicity Not available. Teratogenicity Not available. Reproductive toxicity Not available. Irritation/Corrosion Not available. Sensitization Not available. Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Not available. Not available. Aspiration hazard Name Result Distillates (petroleum), hydrotreated light paraffinic ASPIRATION HAZARD - Category 1 Distillates (petroleum), solvent-dewaxed light paraffinic ASPIRATION HAZARD - Category 1 Alkyl Phosphites ASPIRATION HAZARD - Category 1 Information on toxicological effects Date of issue/Date of revision : 11/11/2024 Version : 4 7/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 11. Toxicological information Not available. Information on the likely routes of exposure Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact No known significant effects or critical hazards.General : No known significant effects or critical hazards.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Potential chronic health effects Delayed and immediate effects and also chronic effects from short and long term exposure : Not available. Potential acute health effects Potential immediate effects : Not available. Short term exposure Potential delayed effects : Not available. Potential immediate effects : Not available. Long term exposure Potential delayed effects : Not available. Numerical measures of toxicity Acute toxicity estimates Product/ingredient name Bel-Ray D/M ATF N/A 52291.3 N/A N/A N/A Distillates (petroleum), hydrotreated heavy paraffinic N/A 2500 N/A N/A 5.7 Distillates (petroleum), hydrotreated light paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), solvent-dewaxed light paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), solvent-dewaxed heavy paraffinic N/A 2500 N/A N/A N/A Alkyl Phosphites 2500 1100 N/A N/A N/A Oral (mg/ kg) Dermal (mg/kg) Inhalation (gases) (ppm) Inhalation (vapors) (mg/l) Inhalation (dusts and mists) (mg/ l) No known significant effects or critical hazards.Reproductive toxicity : Date of issue/Date of revision : 11/11/2024 Version : 4 8/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 12. Ecological information Bioaccumulative potential Product/ingredient name Aquatic half-life Photolysis Biodegradability Distillates (petroleum), hydrotreated heavy paraffinic - - Not readily Distillates (petroleum), hydrotreated light paraffinic - - Inherent 1-(tert-dodecylthio)propan-2-ol - - Not readily Alkyl Phosphites - - Not readily Toxicity Distillates (petroleum), hydrotreated heavy paraffinic Acute EC50 >100 mg/l Daphnia 48 hours Acute IC50 >100 mg/l Algae 72 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), hydrotreated light paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), solvent-dewaxed light paraffinic Acute LC50 4.5 mg/l Fish 96 hours Distillates (petroleum), solvent-dewaxed heavy paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Chronic NOEL >1 mg/l Daphnia 21 days 1-(tert-dodecylthio)propan-2-ol EC50 >100 mg/l Algae 4 days EC50 0.58 mg/l Daphnia 2 days LC50 0.75 mg/l Fish 4 days NOEC 100 mg/l Algae 4 days NOEC 0.32 mg/l Daphnia 2 days NOEC 0.56 mg/l Fish 4 days Alkyl Phosphites Acute EC50 0.09 mg/l Daphnia 48 hours Acute LC50 1.5 mg/l Fresh water Fish 96 hours Acute NOEC 0.13 mg/l Algae 72 hours Product/ingredient name SpeciesResult Exposure Persistence and degradability 1-(tert-dodecylthio)propan-2-ol OECD 301F Ready Biodegradability - Manometric Respirometry Test 5.9 % - Not readily - 28 days - - Alkyl Phosphites - 52.9 % - Not readily - 60 days - - OECD 301B Ready Biodegradability - CO? Evolution Test 52.9 % - Not readily - 60 days 10 mg/l Activated sludge Product/ingredient name Test DoseResult Inoculum Date of issue/Date of revision : 11/11/2024 Version : 4 9/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 12. Ecological information LogPow BCF Potential Other adverse effects : No known significant effects or critical hazards. Product/ingredient name Distillates (petroleum), hydrotreated heavy paraffinic >6 - High Distillates (petroleum), hydrotreated light paraffinic >6 - High Distillates (petroleum), solvent-dewaxed heavy paraffinic 2 to 6 - High Soil/water partition coefficient (KOC) : Not available. Mobility in soil Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. :Disposal methods RCRA classification : Not Regulated Section 14. Transport information Environmentally hazardous substance, liquid, n.o.s. (1-(tert- dodecylthio)propan- 2-ol). Marine pollutant 9 III ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (1-(tert- dodecylthio)propan- 2-ol). Marine pollutant (1-(tert-dodecylthio) propan-2-ol) 9 III Environmentally hazardous substance, liquid, n.o.s. (1-(tert- dodecylthio)propan-2-ol) UN3082 9 III UN3082 UN3082 DOT Classification IMDG IATA UN number UN proper shipping name Transport hazard class(es) Packing group Environmental hazards Yes. Yes. Yes. TDG Classification UN3082 ENVIRONMENTALLY HAZARDOUS SUBSTANCE, LIQUID, N.O.S. (1-(tert- dodecylthio)propan- 2-ol). Marine pollutant (1-(tert-dodecylthio) propan-2-ol) 9 III Yes. Additional information Date of issue/Date of revision : 11/11/2024 Version : 4 10/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 14. Transport information Non-bulk packages of this product are not regulated as hazardous materials unless transported by inland waterway. This product is not regulated as a hazardous material when transported in sizes of ?5 L or ?5 kg, provided the packagings meet the general provisions of ?? 173.24 and 173.24a. Limited quantity Yes. Packaging instruction Exceptions: 155. Non-bulk: 203. Bulk: 241. Special provisions 8, 146, 173, 335, 441, IB3, T4, TP1, TP29 This product is not regulated as a dangerous good when transported in sizes of ?5 L or ?5 kg, provided the packagings meet the general provisions of 4.1.1.1, 4.1.1.2 and 4.1.1.4 to 4.1.1.8. Emergency schedules F-A, S-F Special provisions 274, 335, 969 This product is not regulated as a dangerous good when transported in sizes of ?5 L or ?5 kg, provided the packagings meet the general provisions of 5.0.2.4.1, 5.0.2.6.1.1 and 5.0.2.8. Quantity limitation Passenger and Cargo Aircraft: 450 L. Packaging instructions: 964. Cargo Aircraft Only: 450 L. Packaging instructions: 964. Limited Quantities - Passenger Aircraft: 30 kg. Packaging instructions: Y964. Special provisions A97, A158, A197, A215 Special precautions for user Transport in bulk according to IMO instruments Transport within user?s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : Not available. : Product classified as per the following sections of the Transportation of Dangerous Goods Regulations: 2.43-2.45 (Class 9), 2.7 (Marine pollutant mark). Non-bulk packages of this product are not regulated as dangerous goods when transported by road or rail. Explosive Limit and Limited Quantity Index 5 Special provisions 16, 99 DOT Classification TDG Classification IMDG IATA : : : : Section 15. Regulatory information U.S. Federal regulations TSCA 4(a) proposed test rules: methyl-1H-benzotriazole Clean Water Act (CWA) 307: benzene; ethylbenzene Clean Water Act (CWA) 311: benzene; xylene; ethylbenzene : Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) : Listed Clean Air Act Section 602 Class I Substances : Not listed Clean Air Act Section 602 Class II Substances : Not listed DEA List I Chemicals (Precursor Chemicals) : Not listed DEA List II Chemicals (Essential Chemicals) : Not listed TSCA 8(a) CDR Exempt/Partial exemption: Not determined TSCA 8(c) calls for record of SAR: trimethyl phosphate SARA 302/304 Composition/information on ingredients Date of issue/Date of revision : 11/11/2024 Version : 4 11/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 15. Regulatory information Viet Nam None of the components are listed.Massachusetts : California Prop. 65 New York : None of the components are listed. New Jersey : None of the components are listed. Pennsylvania : None of the components are listed. State regulations SARA 304 RQ : 117576236.4 lbs / 53379611.3 kg [16601602.9 gal / 62843903.2 L] sulphur dioxide ?0.1 Yes. 500 - 500 - Name % EHS (lbs) (lbs)(gallons) (gallons) SARA 302 TPQ SARA 304 RQ International lists National inventory Australia : All components are listed or exempted. Canada : All components are listed or exempted. China : Not determined. Republic of Korea : All components are listed or exempted. New Zealand : All components are listed or exempted. Philippines : All components are listed or exempted. Taiwan : All components are listed or exempted. Turkey : Not determined. United States Thailand : Not determined. SARA 311/312 Classification : Not applicable. Distillates (petroleum), hydrotreated light paraffinic ?3 ASPIRATION HAZARD - Category 1 Distillates (petroleum), solvent- dewaxed light paraffinic ?3 ASPIRATION HAZARD - Category 1 Name % Classification Composition/information on ingredients WARNING: This product can expose you to chemicals including Benzene, which is known to the State of California to cause cancer and birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Benzene 0 - 0.0079 Yes. Yes. Ethylbenzene 0.00125 Yes. - sulfur dioxide 0 - 0.00042526 - Yes. Ingredient name No significant risk level Maximum acceptable dosage level : All ingredients listed and active or exempt. Not determined. Concentration (% ) Information provided is based on industrial use and may not be relevant to consumer applications. Eurasian Economic Union : Russian Federation inventory: Not determined. Date of issue/Date of revision : 11/11/2024 Version : 4 12/13Date of previous issue : 02/26/2021 FVP PREMIUM ATF QUART Section 16. Other information History Date of issue/Date of revision Version Notice to reader Date of previous issue : : : Indicates information that has changed from previously issued version. Key to abbreviations : 11/11/2024 02/26/2021 4 0 1 0 National Fire Protection Association (U.S.A.) Health Special Instability/Reactivity Flammability Reprinted with permission from NFPA 704-2001, Identification of the Hazards of Materials for Emergency Response Copyright ?1997, National Fire Protection Association, Quincy, MA 02269. This reprinted material is not the complete and official position of the National Fire Protection Association, on the referenced subject which is represented only by the standard in its entirety. Copyright ?2001, National Fire Protection Association, Quincy, MA 02269. This warning system is intended to be interpreted and applied only by properly trained individuals to identify fire, health and reactivity hazards of chemicals. The user is referred to certain limited number of chemicals with recommended classifications in NFPA 49 and NFPA 325, which would be used as a guideline only. Whether the chemicals are classified by NFPA or not, anyone using the 704 systems to classify chemicals does so at their own risk. Procedure used to derive the classification Classification Justification AQUATIC HAZARD (ACUTE) - Category 2 Calculation method AQUATIC HAZARD (LONG-TERM) - Category 2 Calculation method ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Date of issue/Date of revision : 11/11/2024 Version : 4 13/13Date of previous issue : 02/26/2021