FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Not available. Liquid. INFOTRAC 1-800-535-5053 SAFETY DATA SHEET GHS product identifier Other means of identification Product type Emergency telephone number (with hours of operation) Section 1. Identification : : : : Supplier's details : Factory Motor Parts 1380 Corporate Center Curve, Suite 200 Eagan, MN 55121 866-387-3343 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Relevant identified uses of the substance or mixture and uses advised against Lubricating Oil Synthetic Identified uses Not applicable. Uses advised against Product code : 5W30FS-QT Section 2. Hazards identification SKIN SENSITIZATION - Category 1Classification of the substance or mixture : Signal word : Warning Hazard statements : May cause an allergic skin reaction. Hazard pictograms : Precautionary statements Prevention : Wear protective gloves. Avoid breathing vapor. Response : IF ON SKIN: Wash with plenty of water. If skin irritation or rash occurs: Get medical advice or attention. Wash contaminated clothing before reuse. Storage : Not applicable. Disposal : Dispose of contents and container in accordance with all local, regional, national and international regulations. GHS label elements General : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. Hazards not otherwise classified : None known. OSHA/HCS status : This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 1/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 3. Composition/information on ingredients Ingredient name Identifiers% There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Other means of identification : Not available. Substance/mixture : Occupational exposure limits, if available, are listed in Section 8. Mixture Any concentration shown as a range is to protect confidentiality or is due to batch variation. Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based ?90 CAS: 72623-87-1 Distillates (petroleum), hydrotreated heavy paraffinic ?10 - ?25 CAS: 64742-54-7 Distillates (petroleum), solvent-dewaxed heavy paraffinic ?10 CAS: 64742-65-0 Distillates (petroleum), solvent-dewaxed light paraffinic ?5 CAS: 64742-56-9 Distillates (petroleum), hydrotreated light paraffinic ?5 CAS: 64742-55-8 zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis(phosphorodithioate) <2.5 CAS: 2215-35-2 dihydro-3-(octadecenyl)furan-2,5-dione ?0.3 CAS: 28777-98-2 The classification as a carcinogen need not apply if it can be shown that the substance contains less than 3 % DMSO extract as measured by IP 346 Wash out mouth with water. Remove dentures if any. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention if irritation occurs. Wash with plenty of soap and water. Remove contaminated clothing and shoes. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Continue to rinse for at least 10 minutes. Get medical attention. In the event of any complaints or symptoms, avoid further exposure. Wash clothing before reuse. Clean shoes thoroughly before reuse. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion : : : : Description of necessary first aid measures Most important symptoms/effects, acute and delayed Inhalation : No known significant effects or critical hazards. Skin contact : May cause an allergic skin reaction. No known significant effects or critical hazards.:Eye contact Potential acute health effects Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 2/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 4. First aid measures Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Wash contaminated clothing thoroughly with water before removing it, or wear gloves. Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments : No specific treatment. No known significant effects or critical hazards.:Ingestion Over-exposure signs/symptoms Skin contact Ingestion Inhalation No specific data. No specific data. Adverse symptoms may include the following: irritation redness : : : Eye contact : No specific data. See toxicological information (Section 11) Indication of immediate medical attention and special treatment needed, if necessary Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide sulfur oxides phosphorus oxides metal oxide/oxides In a fire or if heated, a pressure increase will occur and the container may burst. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters Use an extinguishing agent suitable for the surrounding fire. Extinguishing media : : : Do not use water jet. Suitable extinguishing media : Unsuitable extinguishing media : Special protective actions for fire-fighters : Section 6. Accidental release measures Environmental precautions Personal precautions, protective equipment and emergency procedures : : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). For non-emergency personnel For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 3/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 6. Accidental release measures Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations. Large spill : Stop leak if without risk. Move containers from spill area. Absorb with an inert material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : : Protective measures Put on appropriate personal protective equipment (see Section 8). Persons with a history of skin sensitization problems should not be employed in any process in which this product is used. Do not get in eyes or on skin or clothing. Do not ingest. Avoid breathing vapor or mist. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. : Precautions for safe handling Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m?. Form: Mist. STEL 15 minutes: 10 mg/m?. Form: Mist. Distillates (petroleum), hydrotreated heavy paraffinic NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m?. Form: Mist. STEL 15 minutes: 10 mg/m?. Form: Mist. OSHA PEL (United States, 5/2018) [Oil mist, mineral] TWA 8 hours: 5 mg/m?. ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and severely refined] A4. TWA 8 hours: 5 mg/m?. Form: Inhalable fraction. Distillates (petroleum), solvent-dewaxed heavy paraffinic NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m?. Form: Mist. STEL 15 minutes: 10 mg/m?. Form: Mist. Section 8. Exposure controls/personal protection Ingredient name Exposure limits Control parameters Occupational exposure limits Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 4/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 8. Exposure controls/personal protection OSHA PEL (United States, 5/2018) [Oil mist, mineral] TWA 8 hours: 5 mg/m?. ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and severely refined] A4. TWA 8 hours: 5 mg/m?. Form: Inhalable fraction. Distillates (petroleum), solvent-dewaxed light paraffinic NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m?. Form: Mist. STEL 15 minutes: 10 mg/m?. Form: Mist. OSHA PEL (United States, 5/2018) [Oil mist, mineral] TWA 8 hours: 5 mg/m?. ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and severely refined] A4. TWA 8 hours: 5 mg/m?. Form: Inhalable fraction. Distillates (petroleum), hydrotreated light paraffinic NIOSH REL (United States, 10/2020) [OIL MIST MINERAL] TWA 10 hours: 5 mg/m?. Form: Mist. STEL 15 minutes: 10 mg/m?. Form: Mist. OSHA PEL (United States, 5/2018) [Oil mist, mineral] TWA 8 hours: 5 mg/m?. ACGIH TLV (United States, 1/2024) [Mineral Oil, pure, highly and severely refined] A4. TWA 8 hours: 5 mg/m?. Form: Inhalable fraction. zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis(phosphorodithioate) None. dihydro-3-(octadecenyl)furan-2,5-dione None. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side- shields. Eye/face protection : Environmental exposure controls : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate engineering controls : Good general ventilation should be sufficient to control worker exposure to airborne contaminants. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Contaminated work clothing must not be allowed out of the workplace Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Biological exposure indices No exposure indices known. Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 5/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 8. Exposure controls/personal protection Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Respiratory protection : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. : Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Section 9. Physical and chemical properties and safety characteristics Physical state Melting point/freezing point Vapor pressure Relative density Relative vapor density Solubility(ies) Liquid. Not available. 0.849 Not available. Characteristic.Odor pH Pale color. Yellow.Color Evaporation rate Not available. Auto-ignition temperature Flash point Closed cup: 208?C (406.4?F) [Pensky-Martens] Not applicable. Not available. Not available.Odor threshold Partition coefficient: n- octanol/water : : : : : : : : : : : : : : Appearance Boiling point or initial boiling point and boiling range : Not available. Flammability : Not available. Lower and upper explosion limit/flammability limit : Not available. Solubility in water : Not available. The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Ingredient name Vapor Pressure at 20?C Vapor pressure at 50?C mm Hg kPa Method mm Hg kPa Method Lubricating oils (petroleum), C20-50, hydrotreated neutral oil- based <0.07501 <0.01 ASTM D 5191 Media Result cold water Not soluble hot water Not soluble Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 6/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 9. Physical and chemical properties and safety characteristics Viscosity Dynamic (room temperature): Not available. Kinematic (room temperature): Not available. Kinematic (40?C (104?F)): 55.2 mm2/s (55.2 cSt) : Decomposition temperature : Not available. Particle characteristics Median particle size : Not applicable. Ingredient name ?C ?F Method zinc bis(O,O-diisooctyl) bis(dithiophosphate) 198 388.4 Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid No specific data. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable.Chemical stability No specific data. : : : Incompatible materials : Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity : No specific test data related to reactivity available for this product or its ingredients. Section 11. Toxicological information Acute toxicity Information on toxicological effects Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based Rat - Oral - LD50 >5000 mg/kg Rabbit - Dermal - LD50 >2000 mg/kg Rat - Inhalation - LC50 Dusts and mists 2.18 mg/l [4 hours] Distillates (petroleum), hydrotreated heavy paraffinic Rat - Oral - LD50 >5000 mg/kg Rabbit - Dermal - LD50 >2000 mg/kg Rat - Inhalation - LC50 Dusts and mists 5.7 mg/l [4 hours] Distillates (petroleum), solvent-dewaxed heavy paraffinic Rat - Oral - LD50 >5000 mg/kg Rabbit - Dermal - LD50 >2000 mg/kg Rat - Inhalation - LC50 Dusts and mists >5.53 mg/l [4 hours] Distillates (petroleum), solvent-dewaxed light paraffinic Rabbit - Dermal - LD50 >5000 mg/kg Rat - Oral - LD50 >5000 mg/kg Rat - Dermal - LD50 >2000 mg/kg Distillates (petroleum), hydrotreated light Rat - Oral - LD50 Product/ingredient name Result Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 7/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 11. Toxicological information paraffinic >5000 mg/kg Rabbit - Dermal - LD50 >2000 mg/kg Rat - Inhalation - LC50 Dusts and mists >5.53 mg/l [4 hours] zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Rat - Oral - LD50 2600 mg/kg Rabbit - Dermal - LD50 >3160 mg/kg OECD [Acute Dermal Toxicity] Rat - Inhalation - LC50 Dusts and mists >2 mg/l [1 hours] OECD [Acute Inhalation Toxicity] dihydro-3-(octadecenyl)furan-2,5-dione Rat - Oral - LD50 >2000 mg/kg OECD [Acute Oral Toxicity: Up-and-Down Procedure] Rat - Dermal - LD50 >2000 mg/kg OECD [Acute Dermal Toxicity] Conclusion/Summary [Product] : Not available. Skin corrosion/irritation zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Rat - Skin - Moderate irritant dihydro-3-(octadecenyl)furan-2,5-dione Rabbit - Skin - Irritant OECD [Acute Dermal Irritation/Corrosion] Duration of treatment/exposure: 4 hours Product/ingredient name Result Conclusion/Summary [Product] : Not available. Not available.Conclusion/Summary [Product] Serious eye damage/eye irritation zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Rat - Eyes - Moderate irritant Product/ingredient name Result : : Not available.Conclusion/Summary [Product] Respiratory corrosion/irritation Not available. Respiratory or skin sensitization zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Guinea pig - skin OECD [Skin Sensitization] Result: Not sensitizing dihydro-3-(octadecenyl)furan-2,5-dione Guinea pig - skin OECD [Skin Sensitization] Result: Sensitizing Product/ingredient name Result Skin Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 8/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 11. Toxicological information Potential acute health effects : Not available. Respiratory : Not available. Conclusion/Summary [Product] Conclusion/Summary [Product] Germ cell mutagenicity zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Bacteria OECD [Bacterial Reverse Mutation Test] Result: Negative Product/ingredient name Result : Not available.Conclusion/Summary [Product] Carcinogenicity Not available. : Not available. Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based Note L: The classification as a carcinogen need not apply if it can be shown that the substance contains less than 3 % DMSO extract as measured by IP 346 ?Determination of polycyclic aromatics in unused lubricating base oils and asphaltene free petroleum fractions ? Dimethyl sulphoxide extraction refractive index method?, Institute of Petroleum, London. This note applies only to certain complex oilderived substances in Part 3. Ingredient name Conclusion/Summary Conclusion/Summary [Product] Reproductive toxicity Product/ingredient name Result : Not available. zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) Rat - Male, Female - Oral OECD [Combined Repeated Dose Toxicity Study with the Reproduction/Developmental Toxicity Screening Test] 160 mg/kg Conclusion/Summary [Product] Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Not available. Not available. Aspiration hazard Product/ingredient name Result Distillates (petroleum), solvent-dewaxed light paraffinic ASPIRATION HAZARD - Category 1 Distillates (petroleum), hydrotreated light paraffinic ASPIRATION HAZARD - Category 1 Information on the likely routes of exposure Not available. Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 9/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 11. Toxicological information Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : May cause an allergic skin reaction. No known significant effects or critical hazards.:Eye contact Once sensitized, a severe allergic reaction may occur when subsequently exposed to very low levels. General : No known significant effects or critical hazards.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : No known significant effects or critical hazards.Reproductive toxicity : Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation No specific data. No specific data. Adverse symptoms may include the following: irritation redness : : : Eye contact : No specific data. Delayed and immediate effects and also chronic effects from short and long term exposure Numerical measures of toxicity Acute toxicity estimates Potential immediate effects : Not available. Short term exposure Potential delayed effects : Not available. Potential immediate effects : Not available. Long term exposure Potential delayed effects : Not available. Product/ingredient name Bel-Ray BRX Elite Full Synthetic 5W-30 400959.4 44345.7 N/A N/A N/A Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated heavy paraffinic N/A 2500 N/A N/A 5.7 Distillates (petroleum), solvent-dewaxed heavy paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), solvent-dewaxed light paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated light paraffinic N/A 2500 N/A N/A N/A zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) 2600 2500 N/A N/A N/A dihydro-3-(octadecenyl)furan-2,5-dione 2500 2500 N/A N/A N/A Oral (mg/ kg) Dermal (mg/kg) Inhalation (gases) (ppm) Inhalation (vapors) (mg/l) Inhalation (dusts and mists) (mg/l) Not available. Potential chronic health effects Conclusion/Summary [Product] : Not available. Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 10/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 12. Ecological information Toxicity Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based Acute - LC50 Fish >100 mg/l [96 hours] Acute - EC50 Crustaceans >100 mg/l [48 hours] Acute - EC50 Algae >100 mg/l [72 hours] Distillates (petroleum), hydrotreated heavy paraffinic Acute - IC50 Algae >100 mg/l [72 hours] Acute - EC50 Daphnia >100 mg/l [48 hours] Acute - LC50 Fish >100 mg/l [96 hours] Distillates (petroleum), solvent-dewaxed heavy paraffinic Acute - LC50 Fish >100 mg/l [96 hours] Acute - EC50 Daphnia >100 mg/l [48 hours] Acute - EC50 Algae >100 mg/l [72 hours] Chronic - NOEL Daphnia >1 mg/l [21 days] Distillates (petroleum), solvent-dewaxed light paraffinic Acute - LC50 Fish - Trout 4.5 mg/l [96 hours] Distillates (petroleum), hydrotreated light paraffinic Acute - EC50 Daphnia >100 mg/l [48 hours] Acute - EC50 Algae >100 mg/l [72 hours] Acute - LC50 Fish >100 mg/l [96 hours] zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) LC50 Fish - Trout 4.5 mg/l [4 days] NOEC Fish - Trout 1.8 mg/l [4 days] EC50 Daphnia - Daphnia 23 mg/l [2 days] NOEC Daphnia 0.4 mg/l [21 days] EC50 Aquatic plants - Algae >100 mg/l [3 days] dihydro-3-(octadecenyl)furan-2,5-dione Acute - LC50 Product/ingredient name Result Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 11/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects No known significant effects or critical hazards. Product/ingredient name Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based >6 - High Distillates (petroleum), hydrotreated heavy paraffinic >6 - High Distillates (petroleum), solvent-dewaxed heavy paraffinic 2 to 6 - High Distillates (petroleum), hydrotreated light paraffinic >6 - High Product/ingredient name Aquatic half-life Photolysis Biodegradability Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based - - Inherent Distillates (petroleum), hydrotreated heavy paraffinic - - Not readily Distillates (petroleum), hydrotreated light paraffinic - - Inherent zinc O,O,O',O'-tetrakis (1,3-dimethylbutyl) bis (phosphorodithioate) - - Not readily Persistence and degradability Soil/Water partition coefficient : Not available. Mobility in soil OECD [Fish, Acute Toxicity Test] Fish >10 mg/l [96 hours] : Not available.Conclusion/Summary [Product] zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) OECD [Ready Biodegradability - CO? Evolution Test] 1.5% [28 days] OECD [Ready Biodegradability - CO? Evolution Test] 1.5% [28 days] - Not readily Product/ingredient name Result : Not available.Conclusion/Summary [Product] Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been :Disposal methods Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 12/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 13. Disposal considerations cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14. Transport information - - - - - - - Not regulated. - - Not regulated. Not regulated. DOT Classification UN number UN proper shipping name Transport hazard class(es) Packing group Environmental hazards Special precautions for user No. No. No. Transport within user?s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : Not regulated. - - - No. Not regulated. - - - No. TDG Classification Mexico Classification IMDG IATA Transport in bulk according to IMO instruments : Not available. Section 15. Regulatory information U.S. Federal regulations TSCA 4(a) proposed test rules: dihydro-3-(octadecenyl)furan-2,5-dione Clean Water Act (CWA) 307: zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate); zinc bis(O,O-diisooctyl) bis(dithiophosphate) : Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) : Not listed Clean Air Act Section 602 Class I Substances : Not listed Clean Air Act Section 602 Class II Substances : Not listed DEA List I Chemicals (Precursor Chemicals) : Not listed DEA List II Chemicals (Essential Chemicals) : Not listed TSCA 8(a) CDR Exempt/Partial exemption: Not determined SARA 302/304 SARA 304 RQ : Not applicable. No products were found. Composition/information on ingredients SARA 311/312 Classification : SKIN SENSITIZATION - Category 1 Not applicable. TSCA 12(b) - Chemical export notification Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 13/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 15. Regulatory information None of the components are listed. This product does not require a Safe Harbor warning under California Prop. 65. Massachusetts : SARA 313 Product name CAS number % SARA 313 notifications must not be detached from the SDS and any copying and redistribution of the SDS shall include copying and redistribution of the notice attached to copies of the SDS subsequently redistributed. zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) 2215-35-2 <2.5 zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate) 2215-35-2 <2.5 Form R - Reporting requirements Supplier notification California Prop. 65 New York : None of the components are listed. New Jersey : The following components are listed: ZINC compounds Pennsylvania : The following components are listed: ZINC COMPOUNDS State regulations International regulations Chemical Weapon Convention List Schedules I, II & III Chemicals Montreal Protocol Not listed. Stockholm Convention on Persistent Organic Pollutants Not listed. Rotterdam Convention on Prior Informed Consent (PIC) Not listed. UNECE Aarhus Protocol on POPs and Heavy Metals Not listed. Inventory list Australia : All components are listed or exempted. Canada : All components are listed or exempted. China : All components are listed, exempted, or notified. Japan : Japan inventory (CSCL): Not determined. Japan inventory (ISHL): Not determined. Republic of Korea : All components are listed or exempted. New Zealand : All components are listed or exempted. Philippines : All components are listed, exempted, or notified. Distillates (petroleum), solvent- dewaxed light paraffinic ?5 ASPIRATION HAZARD - Category 1 Distillates (petroleum), hydrotreated light paraffinic ?5 ASPIRATION HAZARD - Category 1 zinc O,O,O',O'-tetrakis (1,3-dimethylbutyl) bis (phosphorodithioate) <2.5 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A dihydro-3-(octadecenyl)furan- 2,5-dione ?0.3 SKIN IRRITATION - Category 2 EYE IRRITATION - Category 2A SKIN SENSITIZATION - Category 1 Name % Classification Composition/information on ingredients Not listed. Eurasian Economic Union : Russian Federation inventory: Not determined. Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 14/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 15. Regulatory information Taiwan : All components are listed or exempted. Turkey : Not determined. United States : All components are active or exempted. Thailand : Not determined. Viet Nam : Not determined. Section 16. Other information 5/8/2025 History Date of printing Date of issue/Date of revision Version Notice to reader Date of previous issue : : : : Indicates information that has changed from previously issued version. References : Not available. Key to abbreviations : ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor DOT = Department of Transportation GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods IMO = International Maritime Organization LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group TDG = Transportation of Dangerous Goods UN = United Nations 5/8/2025 3/19/2025 5 Hazardous Material Information System (U.S.A.) 2 1 0 0 1 0 / National Fire Protection Association (U.S.A.) Health Special hazards Instability Flammability Health Flammability Physical hazards Caution: HMIS? ratings are based on a 0-4 rating scale, with 0 representing minimal hazards or risks, and 4 representing significant hazards or risks. Although HMIS? ratings and the associated label are not required on SDSs or products leaving a facility under 29 CFR 1910.1200, the preparer may choose to provide them. HMIS? ratings are to be used with a fully implemented HMIS? program. HMIS? is a registered trademark and service mark of the American Coatings Association, Inc. The customer is responsible for determining the PPE code for this material. For more information on HMIS? Personal Protective Equipment (PPE) codes, consult the HMIS? Implementation Manual. Procedure used to derive the classification Classification Justification SKIN SENSITIZATION - Category 1 Calculation method Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 15/16 FVP FULL SYNTHETIC 5W-30 MOTOR OIL QUART Section 16. Other information To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Date of issue/Date of revision : 5/8/2025 Date of previous issue : 3/19/2025 Version : 5 16/16