Material Safety Data Sheet 1. PRODUCT IDENTIFICATION Product Name: THE RIGHT STUFF FOR IMPORTS POWERBEAD 7.5 OZ AE Item No: 85144 Product Type: Elastomeric rubber (pressurized) 2. COMPOSITION/INFORMATION ON INGREDIENTS Component Weight% ACGIH; TLV-TWA OSHA PEL POLY (DIMETHYLSILOXANE), HYDROXY TERMINATED 70131-67-8 40-50 Not listed Not listed CALCIUM CARBONATE 471-34-1 20-30 10 mg/m3 Not listed GARNET MINERAL 1302-62-1 20-30 Not listed Not listed VINYL OXIMINOSILANE 2224-33-1 <7 Not listed Not listed MODIFIED SILICON DIOXIDE 68611-44-9 <5 Not listed Not listed STEARIC ACID 57-11-4 <2 Not listed Not listed 2-BUTANONE OXIME 96-29-7 0.5-2.0 Not listed Not listed NITROGEN 7727-37-9 0.5-2.0 Not listed Not listed 3. HAZARDS IDENTIFICATION Toxicity: May cause eye and skin irritation. May irritate lips, gums, tongue, mouth, nose and throat. When this product if exposed to moisture, butanone oxime may be formed. Note: This product does not contain microcyrstalline silica. Primary Routes of Entry: Eye and skin contact, ingestion, inhalation Signs and Symptoms of Exposure: 2-Butanone oxime produced during cure is toxic and irritates eyes, nose and throat. Overexposure may cause eye and skin redness. Overexposure to nitrogen propellant (only released if can is punctured) may cause headache, drowsiness, dizziness, excitation, excess salivation, vomiting, unconsciousness. Aggravated Medical Condition: None known. 4. FIRST AID MEASURES Ingestion: Rinse mouth. If swallowed, DO NOT induce vomiting. Keep individual calm. Obtain medical attention. Inhalation: Move to fresh air in case of accidental inhalation of vapours. Obtain medical attention. Skin Contact: Wipe off material with paper towel or cloth Wash off with soap and water If skin irritation persists, call a physician Eye Contact: In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists. 5. FIRE FIGHTING MEASURES Flash Point ?F(C?): >200?F TCC Recommended Extinguishing Media: Carbon Dioxide, Dry Chemicals, Foam. Special Fire-Fighting Procedures: ***Warning: This container is pressurized with nitrogen. Do not remove rubber plug. Water spray may be ineffective on flames but should be used to keep fire-exposed containers cool. Hazardous Products of Combustion: Formaldehyde, Silica fume, Oxides of nitrogen, Methyl ethyl ketone, possibly methyl ethyl ketoxime Unusual Fire/Explosion Hazards: Contents under pressure. Heated cans may burst. Use equipment or shielding to protect personnel from bursting containers. 1 of 3 ITW Permatex 10 Columbus Blvd. Hartford, CT 06106 USA Telephone: 1-87-Permatex (877) 376-2839 Emergency: 800-255-3924 (ChemTel) International Emergency: +01-813-248-0585 5. FIRE FIGHTING MEASURES Lower Explosive Limit: Not determined Upper Explosive Limit: Not determined 6. ACCIDENTAL RELEASE MEASURES Spill Procedures: Wipe or scrape up spill material. Maintain good ventilation for large spills. Place scrap material in a well- ventilated area and allow to cure to rubber. Clean up spills thoroughly as residue is slippery. 7. HANDLING AND STORAGE Storage: Store in a dry area below 90 degrees F. Keep container closed when not in use. Exposure to high temperatures may cause container to burst. Handling: Avoid contact with skin and eyes. Do not inhale vapors. Do not wear contact lenses. Wash hands before eating and smoking. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Eyes: Safety glasses. Skin: Neoprene or nitrile gloves recommended. Ventilation: General; local exhaust ventilation as necessary to control any air contaminants to within their exposure limits (or to the lowest feasible levels when limits have not been established) during the use of this product. Respiratory Protection: An approved organic vapor respirator should be worn when exposures are expected to exceed the applicable limits. Comments: When heated to temperatures above 300 degrees F. in the presence of air, this product can form formaldehyde vapors. Formaldehyde is a potential cancer hazard and a known skin and respiratory sensitizer. Safe handling conditions may be maintained by keeping vapor concentrations below the OSHA permissible limit for formaldehyde 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Grey paste Odor: Mild Boiling Point: Not applicable, polymeric material pH: Does not apply Solubility in Water: Polymerized Specific Gravity: 1.45 VOC(Wt.%): <3% Vapor Pressure: <5 mm Hg @ 80?F Vapor Density (Air=1): 3.0 Evaporation Rate: <1 (butyl acetate = 1) 10. STABILITY AND REACTIVITY Chemical Stability: Stable at normal conditions Hazardous Polymerization: Will not occur Incompatabilities: Strong oxidizers, Polymerized by contact with moisture, Acids, Iron Conditions to Avoid: Heat. Exposure to moisture. Hazardous Products of Combustion: Formaldehyde, Silica fume, Oxides of nitrogen, Methyl ethyl ketone, possibly methyl ethyl ketoxime 11. TOXICOLOGICAL INFORMATION See Section 3 12. ECOLOGICAL INFORMATION No data available 13. DISPOSAL CONSIDERATIONS Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations. US EPA Waste Number: NH - Not a RCRA Hazardous Waste Material 14. TRANSPORTATION INFORMATION DOT (49CFR 172) U.S. Department of Transportation - DOT - 49 CFR (Ground) Product Name: Item No. 85144THE RIGHT STUFF FOR IMPORTS POWERBEAD 7.5 OZ AE 14. TRANSPORTATION INFORMATION DOT Shipping Name: Aerosols, Limited Quantity Hazard Class: Class 2.2 UN/ID Number: UN 1950 IATA (Air) Proper Shipping Name: Consumer Commodity (Not more than 1 liter) Class or Division: Class 9 UN/ID Number: ID 8000 IMDG (Vessel) Proper Shipping Name: Aerosols, Limited Quantity Hazard Class: Class 2.2 UN Number: UN 1950 Marine Pollutant: None 15. REGULATORY INFORMATION SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical. NONE California Proposition 65: No California Prop 65 chemicals are known to be present. TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory. 16. OTHER INFORMATION Estimated NFPA Rating: HEALTH 1, FLAMMABILITY 1 , REACTIVITY 0. Estimated HMIS Classification: HEALTH 1, FLAMMABILITY 1, PHYSICAL HAZARD 0 (NFPA is a registered trademark of the National Fire Protection Association) HMIS is a registered trademark of the National Paint and Coatings Association Company: ITW Permatex 10 Columbus Blvd. Hartford, CT USA 06106 Product Name: Revision Number: 8 Item No. 85144 Telephone No.: 1-87-Permatex (877) 376-2839 Prepared By: Denise Boyd, Manager-Environmental, Health & Safety THE RIGHT STUFF FOR IMPORTS POWERBEAD 7.5 OZ AE Revision Date: July 25, 2012 << /ASCII85EncodePages false /AllowTransparency false /AutoPositionEPSFiles true /AutoRotatePages /All /Binding /Left /CalGrayProfile (Dot Gain 20%) /CalRGBProfile (sRGB IEC61966-2.1) /CalCMYKProfile (U.S. Web Coated \050SWOP\051 v2) /sRGBProfile (sRGB IEC61966-2.1) /CannotEmbedFontPolicy /Warning /CompatibilityLevel 1.6 /CompressObjects /Tags /CompressPages true /ConvertImagesToIndexed true /PassThroughJPEGImages true /CreateJDFFile false /CreateJobTicket false /DefaultRenderingIntent /Default /DetectBlends true /DetectCurves 0.0000 /ColorConversionStrategy /LeaveColorUnchanged /DoThumbnails false /EmbedAllFonts true /EmbedOpenType false /ParseICCProfilesInComments true /EmbedJobOptions true /DSCReportingLevel 0 /EmitDSCWarnings false /EndPage -1 /ImageMemory 1048576 /LockDistillerParams false /MaxSubsetPct 100 /Optimize true /OPM 1 /ParseDSCComments true /ParseDSCCommentsForDocInfo true /PreserveCopyPage true /PreserveDICMYKValues true /PreserveEPSInfo true /PreserveFlatness true /PreserveHalftoneInfo false /PreserveOPIComments false /PreserveOverprintSettings true /StartPage 1 /SubsetFonts true /TransferFunctionInfo /Apply /UCRandBGInfo /Preserve /UsePrologue false /ColorSettingsFile () /AlwaysEmbed [ true ] /NeverEmbed [ true ] /AntiAliasColorImages false /CropColorImages true /ColorImageMinResolution 300 /ColorImageMinResolutionPolicy /OK /DownsampleColorImages true /ColorImageDownsampleType /Bicubic /ColorImageResolution 300 /ColorImageDepth -1 /ColorImageMinDownsampleDepth 1 /ColorImageDownsampleThreshold 1.50000 /EncodeColorImages true /ColorImageFilter /DCTEncode /AutoFilterColorImages true /ColorImageAutoFilterStrategy /JPEG /ColorACSImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /ColorImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /JPEG2000ColorACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /JPEG2000ColorImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /GrayImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /JPEG2000GrayACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /JPEG2000GrayImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict << /K -1 >> /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False /Description << /CHS /CHT /DAN /DEU /ESP /FRA /ITA /JPN /KOR /NLD (Gebruik deze instellingen om Adobe PDF-documenten te maken voor kwaliteitsafdrukken op desktopprinters en proofers. De gemaakte PDF-documenten kunnen worden geopend met Acrobat en Adobe Reader 5.0 en hoger.) /NOR /PTB /SUO /SVE /ENU (Use these settings to create Adobe PDF documents for quality printing on desktop printers and proofers. Created PDF documents can be opened with Acrobat and Adobe Reader 5.0 and later.) >> /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ << /AsReaderSpreads false /CropImagesToFrames true /ErrorControl /WarnAndContinue /FlattenerIgnoreSpreadOverrides false /IncludeGuidesGrids false /IncludeNonPrinting false /IncludeSlug false /Namespace [ (Adobe) (InDesign) (4.0) ] /OmitPlacedBitmaps false /OmitPlacedEPS false /OmitPlacedPDF false /SimulateOverprint /Legacy >> << /AddBleedMarks false /AddColorBars false /AddCropMarks false /AddPageInfo false /AddRegMarks false /ConvertColors /NoConversion /DestinationProfileName () /DestinationProfileSelector /NA /Downsample16BitImages true /FlattenerPreset << /PresetSelector /MediumResolution >> /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ] >> setdistillerparams << /HWResolution [2400 2400] /PageSize [612.000 792.000] >> setpagedevice