FVP PARTS WASH SOLVENT 5 GALLON Safety Data Sheet GHS product identifier : ?FVP Parts Wash Solvent 5 Gallon Product code : ?FVPPWS-5GAL Chemical name : ?Distillates (petroleum), hydrotreated light Other means of identification Product type : ?Kerosine - unspecified; Distillates, petroleum, hydrotreated light; Hydrotreated light distillate; Kerosene (petroleum), hydrotreated; HYDROTREATED KEROSENE; Jet fuels; Hydrotreated light distillates (petroleum); DISTILLATES; Deodorized kerosene; Dearomatized kerosine : ?Liquid. Relevant identified uses of the substance or mixture and uses advised against Identified uses Petrochemical industry: Petroleum refining. Solvent. Uses advised against Reason Not available. Supplier's details : ?Factory Motor Parts 1380 Corporate Center Curve Suite 200 Eagan, MN 55121 1-866-387-3343 Emergency telephone number (with hours of operation) : ?24 hr. Infotrac 1-800-535-5053 / International 1-703-527-3887 OSHA/HCS status : ?This material is considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200). Classification of the substance or mixture : FLAMMABLE LIQUIDS - Category 4 ASPIRATION HAZARD - Category 1 GHS label elements Hazard pictograms : Signal word : ?Danger Hazard statements : ?Combustible liquid. May be fatal if swallowed and enters airways. Precautionary statements Prevention : ?Wear protective gloves. Wear eye or face protection. Keep away from flames and hot surfaces. - No smoking. Response : ?IF SWALLOWED: Immediately call a POISON CENTER or physician. Do NOT induce vomiting. Storage : ?Store locked up. Store in a well-ventilated place. Keep cool. Disposal : ?Dispose of contents and container in accordance with all local, regional, national and international regulations. Hazards not otherwise classified : ?None known. Substance/mixture : ?Substance Chemical name : ?Distillates (petroleum), hydrotreated light Other means of identification : ?Kerosine - unspecified; Distillates, petroleum, hydrotreated light; Hydrotreated light distillate; Kerosene (petroleum), hydrotreated; HYDROTREATED KEROSENE; Jet fuels; Hydrotreated light distillates (petroleum); DISTILLATES; Deodorized kerosene; Dearomatized kerosine CAS number/other identifiers CAS number : ?64742-47-8 Ingredient name % CAS number Distillates (petroleum), hydrotreated light 100 64742-47-8 Any concentration shown as a range is to protect confidentiality or is due to batch variation. There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. Occupational exposure limits, if available, are listed in Section 8. Description of necessary first aid measures Eye contact Inhalation Skin contact : ?Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention. : ?Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. : ?Wash skin thoroughly with soap and water or use recognized skin cleanser. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Wash clothing before reuse. Clean shoes thoroughly before reuse. Ingestion : Get medical attention immediately. Call a poison center or physician. Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Aspiration hazard if swallowed. Can enter lungs and cause damage. Do not induce vomiting. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Most important symptoms/effects, acute and delayed Potential acute health effects Eye contact : ?No known significant effects or critical hazards. Inhalation : ?No known significant effects or critical hazards. Skin contact : ?Defatting to the skin. May cause skin dryness and irritation. Ingestion : ?May be fatal if swallowed and enters airways. Over-exposure signs/symptoms Eye contact : ?No specific data. Inhalation Skin contact Ingestion : ?No specific data. : ?Adverse symptoms may include the following: irritation d r y n e s s c r a c k i n g : ?Adverse symptoms may include the following: nausea or vomiting Indication of immediate medical attention and special treatment needed, if necessary Notes to physician : ?Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments : ?No specific treatment. Protection of first-aiders : ?No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. See toxicological information (Section 11) Extinguishing media Suitable extinguishing media Unsuitable extinguishing media : ?Use dry chemical, ?CO?, ?water spray (fog) or foam. : ?Do not use water jet. Specific hazards arising from the chemical Hazardous thermal decomposition products : ?Combustible liquid. In a fire or if heated, a pressure increase will occur and the container may burst, with the risk of a subsequent explosion. The vapor/gas is heavier than air and will spread along the ground. Vapors may accumulate in low or confined areas or travel a considerable distance to a source of ignition and flash back. Runoff to sewer may create fire or explosion hazard. : ?No specific data. Special protective actions for fire-fighters Special protective equipment for fire-fighters : ?Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Move containers from fire area if this can be done without risk. Use water spray to keep fire-exposed containers cool. : ?Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Calumet 142 Flash <1% Section 6. Accidental release measures Personal precautions, protective equipment and emergency procedures For non-emergency personnel : ?No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Shut off all ignition sources. No flares, smoking or flames in hazard area. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. For emergency responders : ?If specialised clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Environmental precautions : ?Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Methods and materials for containment and cleaning up Small spill : Large spill : Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Stop leak if without risk. Move containers from spill area. Use spark-proof tools and explosion-proof equipment. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. Precautions for safe handling? Protective measures : Advice on general : occupational hygiene Conditions for safe storage, : including any incompatibilities Put on appropriate personal protective equipment (see Section 8). Do not swallow. Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Use only with adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Do not enter storage areas and confined spaces unless adequately ventilated. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Store and use away from heat, sparks, open flame or any other ignition source. Use explosion-proof electrical (ventilating, lighting and material handling) equipment. Use only non-sparking tools. Empty containers retain product residue and can be hazardous. Do not reuse container. Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store in a segregated and approved area. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Store locked up. Eliminate all ignition sources. Separate from oxidizing materials. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. Calumet 142 Flash <1% Section 8. Exposure controls/personal protection Control parameters? ?Occupational exposure limits Ingredient name Exposure limits Distillates (petroleum), hydrotreated light ACGIH TLV (United States, 4/2014). Absorbed through skin. TWA: 200 mg/m?, (as total hydrocarbon vapor) 8 hours. Appropriate engineering controls Environmental exposure controls : ?Use only with adequate ventilation. Use process enclosures, local exhaust ventilation or other engineering controls to keep worker exposure to airborne contaminants below any recommended or statutory limits. The engineering controls also need to keep gas, vapor or dust concentrations below any lower explosive limits. Use explosion-proof ventilation equipment. : ?Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Individual protection measures? Hygiene measures : Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Eye/face protection Skin protection? Hand protection Body protection : ?Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side- shields. : ?Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. : ?Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Other skin protection : ?Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. Respiratory protection : Use a properly fitted, air-purifying or air-fed respirator complying with an approved standard if a risk assessment indicates this is necessary. Respirator selection must be based on known or anticipated exposure levels, the hazards of the product and the safe working limits of the selected respirator. Calumet 142 Flash <1% Section 9. Physical and chemical properties Appearance? Physical state Color Odor Odor threshold pH Melting point : ?Liquid. [Mobile liquid.] : ?Colorless. : ?Mild. Hydrocarbon. : ?Not available. : ?Not available. : ?-49?C (-56.2?F) Boiling point : ?190 to 210?C (374 to 410?F) Flash point Evaporation rate : ?Closed cup: 65?C (149?F) [Tagliabue.] [Product does not sustain combustion.] : ?0.03 (butyl acetate = 1) Flammability (solid, gas) : ?Not available. Lower and upper explosive (flammable) limits : ?Lower: 0.6% Upper: 5.5% Vapor pressure Vapor density Relative density Solubility : ?0.072 kPa (0.54 mm Hg) [room temperature] : ?4.5 [Air = 1] : ?0.783 : ?Insoluble in the following materials: cold water and hot water. Solubility in water : ?1.5 g/l Partition coefficient: n- octanol/water Auto-ignition temperature : ?Not applicable. : ?>220?C (>428?F) Decomposition temperature : ?Not available. Viscosity : ?Kinematic (40?C (104?F)): 0.0134 cm?2?/s (1.34 cSt) Reactivity : ?No specific test data related to reactivity available for this product or its ingredients. Chemical stability : ?The product is stable. Possibility of hazardous reactions : ?Under normal conditions of storage and use, hazardous reactions will not occur. Conditions to avoid : ?Avoid all possible sources of ignition (spark or flame). Do not pressurize, cut, weld, braze, solder, drill, grind or expose containers to heat or sources of ignition. Do not allow vapor to accumulate in low or confined areas. Incompatible materials : Reactive or incompatible with the following materials: oxidizing materials Hazardous decomposition products : ?Under normal conditions of storage and use, hazardous decomposition products should not be produced. Calumet 142 Flash <1% Section 11. Toxicological information Information on toxicological effects? ?Acute toxicity Product/ingredient name Result Species Dose Exposure Distillates (petroleum), LD50 Dermal Rabbit >2000 mg/kg - hydrotreated light LD50 Oral Rat >5000 mg/kg - Irritation/Corrosion Not available. Sensitization Not available. Mutagenicity Not available. Carcinogenicity Not available. Reproductive toxicity Not available. Teratogenicity Not available. Specific target organ toxicity (single exposure) Not available. Specific target organ toxicity (repeated exposure) Not available. Aspiration hazard Name Result Distillates (petroleum), hydrotreated light ASPIRATION HAZARD - Category 1 Information on the likely routes of exposure Potential acute health effects : ?Routes of entry anticipated: Oral, Dermal, Inhalation. Eye contact : ?No known significant effects or critical hazards. Inhalation : ?No known significant effects or critical hazards. Skin contact : ?Defatting to the skin. May cause skin dryness and irritation. Ingestion : ?May be fatal if swallowed and enters airways. Symptoms related to the physical, chemical and toxicological characteristics Eye contact : ?No specific data. Inhalation Skin contact Ingestion : ?No specific data. : ?Adverse symptoms may include the following: irritation d r y n e s s c r a c k i n g : ?Adverse symptoms may include the following: nausea or vomiting Delayed and immediate effects and also chronic effects from short and long term exposure? ?Short term exposure Potential immediate effects : ?Not available. Potential delayed effects : ?Not available. Long term exposure Potential immediate effects : ?Not available. Potential delayed effects : ?Not available. Potential chronic health effects Not available. General : Carcinogenicity : Mutagenicity : Teratogenicity : Prolonged or repeated contact can defat the skin and lead to irritation, cracking and/or dermatitis. No known significant effects or critical hazards. No known significant effects or critical hazards. No known significant effects or critical hazards. Developmental effects : ?No known significant effects or critical hazards. Fertility effects : ?No known significant effects or critical hazards. Numerical measures of toxicity Acute toxicity estimates Not available. Toxicity Not available. Persistence and degradability Not available. Bioaccumulative potential Not available. Mobility in soil Soil/water partition coefficient (K?OC?) : ?Not available. Other adverse effects : ?No known significant effects or critical hazards. Calumet 142 Flash <1% Section 13. Disposal considerations Disposal methods : ?The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Vapor from product residues may create a highly flammable or explosive atmosphere inside the container. Do not cut, weld or grind used containers unless they have been cleaned thoroughly internally. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Section 14. Transport information DOT Classification TDG Classification IMDG IATA UN number Not regulated. Not regulated. Not regulated. Not regulated. Special precautions for user Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code : ?Transport within user?s premises: ?always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : ?Not available. U.S. Federal regulations : TSCA 8(a) CDR Exempt/Partial exemption?: This material is listed or exempted. This material is listed or exempted. Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) Clean Air Act Section 602 Class I Substances Clean Air Act Section 602 Class II Substances DEA List I Chemicals (Precursor Chemicals) DEA List II Chemicals (Essential Chemicals) SARA 302/304 : ?Not listed : ?Not listed : ?Not listed : ?Not listed : ?Not listed Composition/information on ingredients No products were found. SARA 304 RQ : ?Not applicable. SARA 311/312 Classification : ?Fire hazard Composition/information on ingredients Name % Fire hazard Sudden release of pressure Reactive Immediate (acute) health hazard Delayed (chronic ) health hazard Distillates (petroleum), hydrotreated light 100 Yes. No. No. No. No. State regulations? Massachusetts : This material is not listed. New York : ?This material is not listed. New Jersey : ?This material is not listed. Pennsylvania : ?This material is not listed. California Prop. 65 This product is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. International lists? ?National inventory Australia : ?This material is listed or exempted. Canada : ?This material is listed or exempted. China : ?This material is listed or exempted. Europe : ?This material is listed or exempted. Japan : ?This material is listed or exempted. Malaysia : ?This material is listed or exempted. New Zealand : ?This material is listed or exempted. Philippines : ?This material is listed or exempted. Republic of Korea : ?This material is listed or exempted. Taiwan : ?This material is listed or exempted. Procedure used to derive the classification Classification Justification Flam. Liq. 4, H227 Asp. Tox. 1, H304 Expert judgment On basis of test data History Date of issue/Date of revision : ?07/11/18 Version : ?2 Key to abbreviations : ?ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL 73/78 = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) UN = United Nations Indicates information that has changed from previously issued version. Notice to reader To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist.