3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 1 of 12 Safety Data Sheet Copyright,2018,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 10-5965-8 Version Number: 37.02 Issue Date: 09/17/18 Supercedes Date: 06/09/16 SECTION 1: Identification 1.1. Product identifier 3M? Auto Bedding and Glazing Compound (Black), PN 08509 Product Identification Numbers ID Number UPC ID Number UPC 62-5562-5209-6 00-51135-08509-7 7000000947 1.2. Recommended use and restrictions on use Recommended use sealant, Sealant 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Flammable Liquid: Category 3. Skin Corrosion/Irritation: Category 2. Carcinogenicity: Category 1A. Specific Target Organ Toxicity (repeated exposure): Category 1. 2.2. Label elements Signal word 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 2 of 12 Danger Symbols Flame | Exclamation mark | Health Hazard | Pictograms Hazard Statements Flammable liquid and vapor. Causes skin irritation. May cause cancer. Causes damage to organs through prolonged or repeated exposure: respiratory system | Precautionary Statements General: Keep out of reach of children. Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Ground/bond container and receiving equipment. Use only non-sparking tools. Take precautionary measures against static discharge. Keep container tightly closed. Use explosion-proof electrical/ventilating/lighting equipment. Do not breathe dust/fume/gas/mist/vapors/spray. Wear protective gloves and eye/face protection. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Response: IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. IF ON SKIN: Wash with plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. Get medical advice/attention if you feel unwell. In case of fire: Use a fire fighting agent suitable for flammable liquids such as dry chemical or carbon dioxide to extinguish. Storage: Store in a well-ventilated place. Keep cool. Store locked up. Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international regulations. 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 3 of 12 6% of the mixture consists of ingredients of unknown acute oral toxicity. 6% of the mixture consists of ingredients of unknown acute dermal toxicity. 44% of the mixture consists of ingredients of unknown acute inhalation toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Kaolin 1332-58-7 15 - 40 Trade Secret * Polybutylene 9003-29-6 15 - 40 Trade Secret * Limestone 1317-65-3 10 - 20 Trade Secret * Stoddard Solvent 8052-41-3 7 - 13 Trade Secret * Lecithins, Soya 8030-76-0 1 - 5 Trade Secret * Palygorskite 12174-11-7 1 - 5 Trade Secret * Polyethylene 9002-88-4 1 - 5 Trade Secret * Carbon Black 1333-86-4 < 1 Trade Secret * Quartz Silica 14808-60-7 < 0.2 Trade Secret * *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for flammable liquids such as dry chemical or carbon dioxide to extinguish. 5.2. Special hazards arising from the substance or mixture Closed containers exposed to heat from fire may build pressure and explode. Hazardous Decomposition or By-Products 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 4 of 12 Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion 5.3. Special protective actions for fire-fighters Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Warning! A motor could be an ignition source and could cause flammable gases or vapors in the spill area to burn or explode. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. 6.3. Methods and material for containment and cleaning up Contain spill. Cover spill area with a fire-extinguishing foam. An appropriate aqueous film forming foam (AFFF) is recommended. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible using non-sparking tools. Place in a metal container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. SECTION 7: Handling and storage 7.1. Precautions for safe handling Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Use only non-sparking tools. Take precautionary measures against static discharge. Do not breathe dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) Wear low static or properly grounded shoes. Use personal protective equipment (gloves, respirators, etc.) as required. To minimize the risk of ignition, determine applicable electrical classifications for the process using this product and select specific local exhaust ventilation equipment to avoid flammable vapor accumulation. Ground/bond container and receiving equipment if there is potential for static electricity accumulation during transfer. Vapors may travel long distances along the ground or floor to an ignition source and flash back. 7.2. Conditions for safe storage including any incompatibilities Store in a well-ventilated place. Keep cool. Keep container tightly closed. Protect from sunlight. Store away from heat. Store away from acids. Store away from oxidizing agents. SECTION 8: Exposure controls/personal protection 8.1. Control parameters 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 5 of 12 Occupational exposure limits If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component. Ingredient C.A.S. No. Agency Limit type Additional Comments Limestone 1317-65-3 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 Kaolin 1332-58-7 ACGIH TWA(respirable fraction):2 mg/m3 A4: Not class. as human carcin KAOLIN, TOTAL DUST 1332-58-7 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 Carbon Black 1333-86-4 ACGIH TWA(inhalable fraction):3 mg/m3 A3: Confirmed animal carcin. Carbon Black 1333-86-4 OSHA TWA:3.5 mg/m3 Quartz Silica 14808-60-7 ACGIH TWA(respirable fraction):0.025 mg/m3 A2: Suspected human carcin. Quartz Silica 14808-60-7 OSHA TWA Table Z- 1(respirable):0.05 mg/m3;TWA Table Z- 3(respirable):0.1 mg/m3 Stoddard Solvent 8052-41-3 ACGIH TWA:100 ppm Stoddard Solvent 8052-41-3 OSHA TWA:2900 mg/m3(500 ppm) ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Use explosion-proof ventilation equipment. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Gloves made from the following material(s) are recommended: Nitrile Rubber Respiratory protection 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 6 of 12 In case of inadequate ventilation wear respiratory protection. An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Odor, Color, Grade: solvent odor black paste Odor threshold No Data Available pH Not Applicable Melting point Not Applicable Boiling Point 315 ?F Flash Point 106 ?F [Test Method:Tagliabue Closed Cup] Evaporation rate <=1 [Ref Std:ETHER=1] Flammability (solid, gas) Not Applicable Flammable Limits(LEL) 0.80 % volume Flammable Limits(UEL) 7.00 % volume Vapor Pressure 2.0000 mmHg Vapor Density >=1.00 [Ref Std:AIR=1] Density 1.366 g/ml Specific Gravity 1.376 [Ref Std:WATER=1] Solubility in Water Nil Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature 254 ?C Decomposition temperature No Data Available Viscosity No Data Available Hazardous Air Pollutants 0 lb HAPS/lb solids Volatile Organic Compounds 138 g/l [Test Method:calculated SCAQMD rule 443.1] Volatile Organic Compounds 10 % weight [Test Method:calculated per CARB title 2] Percent volatile 10 % weight VOC Less H2O & Exempt Solvents 138 g/l [Test Method:calculated SCAQMD rule 443.1] SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid Sparks and/or flames Heat 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 7 of 12 10.5. Incompatible materials Not determined 10.6. Hazardous decomposition products Substance Condition None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. May cause additional health effects (see below). Skin Contact: Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, dryness, cracking, blistering, and pain. Eye Contact: Contact with the eyes during product use is not expected to result in significant irritation. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May cause additional health effects (see below). Additional Health Effects: Prolonged or repeated exposure may cause target organ effects: Pneumoconiosis: Sign/symptoms may include persistent cough, breathlessness, chest pain, increased amounts of sputum, and changes in lung function tests. Carcinogenicity: Contains a chemical or chemicals which can cause cancer. Ingredient CAS No. Class Description Regulation SILICA, CRYS AIRRESP 14808-60-7 Known human carcinogen National Toxicology Program Carcinogens Carbon Black 1333-86-4 Grp. 2B: Possible human carc. International Agency for Research on Cancer Quartz Silica 14808-60-7 Grp. 1: Carcinogenic to humans International Agency for Research on Cancer Toxicological Data 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 8 of 12 If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Dermal No data available; calculated ATE >5,000 mg/kg Overall product Inhalation- Vapor(4 hr) No data available; calculated ATE >50 mg/l Overall product Ingestion No data available; calculated ATE >5,000 mg/kg Polybutylene Dermal Rat LD50 > 10,250 mg/kg Polybutylene Ingestion Rat LD50 > 34,600 mg/kg Kaolin Dermal LD50 estimated to be > 5,000 mg/kg Kaolin Ingestion Human LD50 > 15,000 mg/kg Limestone Dermal Rat LD50 > 2,000 mg/kg Limestone Inhalation- Dust/Mist (4 hours) Rat LC50 3 mg/l Limestone Ingestion Rat LD50 6,450 mg/kg Stoddard Solvent Inhalation- Vapor LC50 estimated to be 20 - 50 mg/l Stoddard Solvent Dermal Rabbit LD50 > 3,000 mg/kg Stoddard Solvent Ingestion Rat LD50 > 5,000 mg/kg Polyethylene Dermal LD50 estimated to be > 5,000 mg/kg Polyethylene Ingestion Rat LD50 > 2,000 mg/kg Carbon Black Dermal Rabbit LD50 > 3,000 mg/kg Carbon Black Ingestion Rat LD50 > 8,000 mg/kg Quartz Silica Dermal LD50 estimated to be > 5,000 mg/kg Quartz Silica Ingestion LD50 estimated to be > 5,000 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value Polybutylene Rabbit Minimal irritation Kaolin Professio nal judgeme nt No significant irritation Limestone Rabbit No significant irritation Stoddard Solvent Rabbit Irritant Polyethylene Professio nal judgeme nt No significant irritation Carbon Black Rabbit No significant irritation Quartz Silica Professio nal judgeme nt No significant irritation Serious Eye Damage/Irritation Name Species Value Polybutylene Rabbit Mild irritant Kaolin Professio nal judgeme nt No significant irritation Limestone Rabbit No significant irritation Stoddard Solvent Rabbit No significant irritation Carbon Black Rabbit No significant irritation 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 9 of 12 Skin Sensitization Name Species Value Stoddard Solvent Guinea pig Not classified Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value Stoddard Solvent In vivo Not mutagenic Stoddard Solvent In Vitro Some positive data exist, but the data are not sufficient for classification Carbon Black In Vitro Not mutagenic Carbon Black In vivo Some positive data exist, but the data are not sufficient for classification Quartz Silica In Vitro Some positive data exist, but the data are not sufficient for classification Quartz Silica In vivo Some positive data exist, but the data are not sufficient for classification Carcinogenicity Name Route Species Value Kaolin Inhalation Multiple animal species Not carcinogenic Stoddard Solvent Dermal Mouse Some positive data exist, but the data are not sufficient for classification Stoddard Solvent Inhalation Human and animal Some positive data exist, but the data are not sufficient for classification Polyethylene Not Specified Multiple animal species Some positive data exist, but the data are not sufficient for classification Carbon Black Dermal Mouse Not carcinogenic Carbon Black Ingestion Mouse Not carcinogenic Carbon Black Inhalation Rat Carcinogenic Quartz Silica Inhalation Human and animal Carcinogenic Reproductive Toxicity Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration Limestone Ingestion Not classified for development Rat NOAEL 625 mg/kg/day premating & during gestation Stoddard Solvent Inhalation Not classified for development Rat NOAEL 2.4 mg/l during organogenesi s Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Limestone Inhalation respiratory system Not classified Rat NOAEL 0.812 mg/l 90 minutes Stoddard Solvent Inhalation central nervous system depression May cause drowsiness or dizziness Human and NOAEL Not available 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 10 of 12 animal Stoddard Solvent Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification NOAEL Not available Stoddard Solvent Inhalation nervous system Not classified Dog NOAEL 6.5 mg/l 4 hours Stoddard Solvent Ingestion central nervous system depression May cause drowsiness or dizziness Professio nal judgeme nt NOAEL Not available Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Polybutylene Inhalation respiratory system Some positive data exist, but the data are not sufficient for classification Rat NOAEL 0.07 mg/l 2 weeks Polybutylene Inhalation liver Not classified Rat NOAEL 0.7 mg/l 2 weeks Kaolin Inhalation pneumoconiosis Causes damage to organs through prolonged or repeated exposure Human NOAEL NA occupational exposure Kaolin Inhalation pulmonary fibrosis Not classified Rat NOAEL Not available Limestone Inhalation respiratory system Not classified Human NOAEL Not available occupational exposure Stoddard Solvent Inhalation nervous system Not classified Rat LOAEL 4.6 mg/l 6 months Stoddard Solvent Inhalation kidney and/or bladder Not classified Rat LOAEL 1.9 mg/l 13 weeks Stoddard Solvent Inhalation respiratory system Not classified Multiple animal species NOAEL 0.6 mg/l 90 days Stoddard Solvent Inhalation bone, teeth, nails, and/or hair | blood | liver | muscles Not classified Rat NOAEL 5.6 mg/l 12 weeks Stoddard Solvent Inhalation heart Not classified Multiple animal species NOAEL 1.3 mg/l 90 days Carbon Black Inhalation pneumoconiosis Not classified Human NOAEL Not available occupational exposure Quartz Silica Inhalation silicosis Causes damage to organs through prolonged or repeated exposure Human NOAEL Not available occupational exposure Aspiration Hazard Name Value Stoddard Solvent Aspiration hazard Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 11 of 12 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Incinerate in a permitted waste incineration facility. As a disposal alternative, utilize an acceptable permitted waste disposal facility. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information. EPCRA 311/312 Hazard Classifications: Physical Hazards Flammable (gases, aerosols, liquids, or solids) Health Hazards Carcinogenicity Skin Corrosion or Irritation Specific target organ toxicity (single or repeated exposure) 15.2. State Regulations Contact 3M for more information. California Proposition 65 Ingredient C.A.S. No. Listing SILICA, CRYSTALLINE (AIRBORNE PARTICLES OF RESPIRABLE SIZE) None Carcinogen CARBON BLACK (AIRBORNE, UNBOUND PARTICLES OF RESPIRABLE SIZE [<= 10 MICROMETERS]) 1333-86-4 Carcinogen 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information 3M? Auto Bedding and Glazing Compound (Black), PN 08509 09/17/18 __________________________________________________________________________________________ Page 12 of 12 NFPA Hazard Classification Health: 2 Flammability: 2 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Document Group: 10-5965-8 Version Number: 37.02 Issue Date: 09/17/18 Supercedes Date: 06/09/16 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from3M 3M USA SDSs are available at www.3M.com