3M? Self-Leveling Seam Sealer, PN 08307 04/05/17 ________________________________________________________________________________________________________ Page 1 of 2 Safety Data Sheet Copyright,2017,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 18-2239-4 Version Number: 3.02 Issue Date: 04/05/17 Supercedes Date: 02/17/16 Product identifier 3M? Self-Leveling Seam Sealer, PN 08307 ID Number(s): 41-0003-8015-8, 41-3700-8997-5, 41-3701-2155-4, 60-9801-0580-7 Recommended use Automotive, Two-part epoxy, self-leveling seam sealer. Supplier's details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) This product is a kit or a multipart product which consists of multiple, independently packaged components. A Safety Data Sheet (SDS), Article Information Sheet (AIS), or Article Information Letter (AIL) for each of these components is included. Please do not separate the component documents from this cover page. The document numbers for components of this product are: 18-2289-9, 18-2290-7 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from3M 3M? Self-Leveling Seam Sealer, PN 08307 04/05/17 ________________________________________________________________________________________________________ Page 2 of 2 3M USA SDSs are available at www.3M.com 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 1 of 10 Safety Data Sheet Copyright,2018,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 18-2289-9 Version Number: 6.00 Issue Date: 06/21/18 Supercedes Date: 04/05/17 SECTION 1: Identification 1.1. Product identifier 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) Product Identification Numbers LB-K100-0061-0 1.2. Recommended use and restrictions on use Recommended use Automotive, This accelerator to be used with 3M(TM) Self-Leveling Seam Sealer - Part B (Base), Two-part epoxy type self- leveling seam sealer - Accelerator 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Serious Eye Damage/Irritation: Category 1. Skin Corrosion/Irritation: Category 1C. Skin Sensitizer: Category 1B. 2.2. Label elements Signal word Danger Symbols 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 2 of 10 Corrosion | Exclamation mark | Pictograms Hazard Statements Causes severe skin burns and eye damage. May cause an allergic skin reaction. Precautionary Statements General: Keep out of reach of children. Prevention: Do not breathe dust/fume/gas/mist/vapors/spray. Wear protective gloves, protective clothing, and eye/face protection. Wash thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace. Response: IF INHALED: Remove person to fresh air and keep comfortable for breathing. IF ON SKIN (or hair): Take off immediately all contaminated clothing. Rinse skin with water/shower. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Immediately call a POISON CENTER or doctor/physician. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse. IF SWALLOWED: Rinse mouth. Do NOT induce vomiting. Storage: Store locked up. Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international regulations. 2.3. Hazards not otherwise classified May cause chemical gastrointestinal burns. 1% of the mixture consists of ingredients of unknown acute dermal toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Mercaptan-Terminated Epoxy Curing Agent Trade Secret* 60 - 100 Trade Secret * Tris(2,4,6-Dimethylaminomonomethyl)Phenol 90-72-2 7 - 13 Trade Secret * Bis[(Dimethylamino)methyl] Phenol 71074-89-0 < 2 Trade Secret * *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 3 of 10 SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately flush with large amounts of water for at least 15 minutes. Remove contaminated clothing. Get immediate medical attention. Wash clothing before reuse. Eye Contact: Immediately flush with large amounts of water for at least 15 minutes. Remove contact lenses if easy to do. Continue rinsing. Immediately get medical attention. If Swallowed: Rinse mouth. Do not induce vomiting. Get immediate medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. 5.3. Special protective actions for fire-fighters Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 4 of 10 SECTION 7: Handling and storage 7.1. Precautions for safe handling Keep out of reach of children. Do not breathe dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment. Wash contaminated clothing before reuse. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) 7.2. Conditions for safe storage including any incompatibilities Store away from acids. Store away from oxidizing agents. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS. 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Full Face Shield Indirect Vented Goggles Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Gloves made from the following material(s) are recommended: Butyl Rubber Neoprene Nitrile Rubber If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an exposure assessment. The following protective clothing material(s) are recommended: Apron - Neoprene Apron ? Nitrile Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 5 of 10 Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Odor, Color, Grade: Yellow liquid with irritating sulfur-like odor. Odor threshold No Data Available pH Not Applicable Melting point Not Applicable Boiling Point >=200 ?F [Test Method:Estimated] Flash Point >=300 ?F [Test Method:Closed Cup] Evaporation rate No Data Available Flammability (solid, gas) Not Applicable Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Vapor Pressure <=27 psia Vapor Density No Data Available Density 1.12 g/ml Specific Gravity 1.12 [Ref Std:WATER=1] Solubility in Water Slight (less than 10%) Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature No Data Available Decomposition temperature No Data Available Viscosity 10,000 - 15,000 centipoise Hazardous Air Pollutants 0.000158 lb HAPS/lb solids [Test Method:Calculated] Volatile Organic Compounds 12 g/l [Test Method:calculated SCAQMD rule 443.1] Volatile Organic Compounds 1.1 % weight [Test Method:calculated per CARB title 2] VOC Less H2O & Exempt Solvents 12 g/l [Test Method:calculated SCAQMD rule 443.1] SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid Not determined 10.5. Incompatible materials Strong acids Strong oxidizing agents 10.6. Hazardous decomposition products Substance Condition 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 6 of 10 Carbon monoxide Not Specified Carbon dioxide Not Specified Oxides of Sulfur Not Specified Toxic Vapor, Gas, Particulate Not Specified SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Corrosive (Skin Burns): Signs/symptoms may include localized redness, swelling, itching, intense pain, blistering, ulceration, and tissue destruction. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Eye Contact: Corrosive (Eye Burns): Signs/symptoms may include cloudy appearance of the cornea, chemical burns, severe pain, tearing, ulcerations, significantly impaired vision or complete loss of vision. Ingestion: May be harmful if swallowed. Gastrointestinal Corrosion: Signs/symptoms may include severe mouth, throat and abdominal pain; nausea; vomiting; and diarrhea; blood in the feces and/or vomitus may also be seen. Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Dermal No data available; calculated ATE >5,000 mg/kg Overall product Ingestion No data available; calculated ATE2,000 - 5,000 mg/kg Mercaptan-Terminated Epoxy Curing Agent Dermal Rabbit LD50 > 10,200 mg/kg Mercaptan-Terminated Epoxy Curing Agent Ingestion Rat LD50 2,600 mg/kg Tris(2,4,6-Dimethylaminomonomethyl)Phenol Dermal Rat LD50 1,280 mg/kg Tris(2,4,6-Dimethylaminomonomethyl)Phenol Ingestion Rat LD50 1,000 mg/kg Bis[(Dimethylamino)methyl] Phenol Ingestion LD50 estimated to be 300 - 2,000 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 7 of 10 Mercaptan-Terminated Epoxy Curing Agent Rabbit No significant irritation Tris(2,4,6-Dimethylaminomonomethyl)Phenol Rabbit Corrosive Bis[(Dimethylamino)methyl] Phenol similar compoun ds Corrosive Serious Eye Damage/Irritation Name Species Value Mercaptan-Terminated Epoxy Curing Agent Rabbit Mild irritant Tris(2,4,6-Dimethylaminomonomethyl)Phenol Rabbit Corrosive Bis[(Dimethylamino)methyl] Phenol similar compoun ds Corrosive Skin Sensitization Name Species Value Mercaptan-Terminated Epoxy Curing Agent Mouse Sensitizing Tris(2,4,6-Dimethylaminomonomethyl)Phenol Guinea pig Not classified Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value Mercaptan-Terminated Epoxy Curing Agent In Vitro Not mutagenic Tris(2,4,6-Dimethylaminomonomethyl)Phenol In Vitro Not mutagenic Carcinogenicity For the component/components, either no data are currently available or the data are not sufficient for classification. Reproductive Toxicity Reproductive and/or Developmental Effects For the component/components, either no data are currently available or the data are not sufficient for classification. Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Tris(2,4,6- Dimethylaminomonomethy l)Phenol Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification NOAEL Not available Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Mercaptan-Terminated Epoxy Curing Agent Ingestion hematopoietic system Some positive data exist, but the data are not sufficient for classification Rat NOAEL 75 mg/kg/day 90 days Mercaptan-Terminated Epoxy Curing Agent Ingestion liver Some positive data exist, but the data are not sufficient for classification Rat NOAEL 250 mg/kg/day 90 days Mercaptan-Terminated Epoxy Curing Agent Ingestion endocrine system | heart | skin | immune system | nervous system | Not classified Rat NOAEL 1,000 mg/kg/day 90 days 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 8 of 10 eyes | kidney and/or bladder | respiratory system | vascular system Tris(2,4,6- Dimethylaminomonomethy l)Phenol Dermal skin | liver | nervous system | auditory system | hematopoietic system | eyes Not classified Rat NOAEL 125 mg/kg/day 28 days Aspiration Hazard For the component/components, either no data are currently available or the data are not sufficient for classification. Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information. EPCRA 311/312 Hazard Classifications: Physical Hazards Not applicable Health Hazards 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 9 of 10 Hazard Not Otherwise Classified (HNOC) Respiratory or Skin Sensitization Serious eye damage or eye irritation Skin Corrosion or Irritation 15.2. State Regulations Contact 3M for more information. 15.3. Chemical Inventories The components of this material are in compliance with the provisions of the Korean Toxic Chemical Control Law. Certain restrictions may apply. Contact the selling division for additional information. The components of this product are in compliance with the chemical notification requirements of TSCA. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 3 Flammability: 1 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. HMIS Hazard Classification Health: 3 Flammability: 1 Physical Hazard: 0 Personal Protection: X - See PPE section. Hazardous Material Identification System (HMIS? IV) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS? IV ratings are to be used with a fully implemented HMIS? IV program. HMIS? is a registered mark of the American Coatings Association (ACA). Document Group: 18-2289-9 Version Number: 6.00 Issue Date: 06/21/18 Supercedes Date: 04/05/17 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the 3M? Self-Leveling Seam Sealer PN 08307 Part A (Accelerator) 06/21/18 __________________________________________________________________________________________ Page 10 of 10 SDS available directly from3M 3M USA SDSs are available at www.3M.com 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 1 of 11 Safety Data Sheet Copyright,2018,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 18-2290-7 Version Number: 5.00 Issue Date: 05/21/18 Supercedes Date: 07/27/17 SECTION 1: Identification 1.1. Product identifier 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 Product Identification Numbers LB-K100-0053-0 1.2. Recommended use and restrictions on use Recommended use Automotive, This base to be used with 3M(TM) Self-Leveling Seam Sealer - Part A (Accelerator), Two-part epoxy type self- leveling seam sealer - Base 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Serious Eye Damage/Irritation: Category 2B. Skin Sensitizer: Category 1. 2.2. Label elements Signal word Warning Symbols Exclamation mark | 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 2 of 11 Pictograms Hazard Statements Causes eye irritation. May cause an allergic skin reaction. Precautionary Statements General: Keep out of reach of children. Prevention: Avoid breathing dust/fume/gas/mist/vapors/spray. Wear protective gloves. Wash thoroughly after handling. Contaminated work clothing must not be allowed out of the workplace. Response: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse. Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international regulations. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer 25068-38-6 50 - 90 Trade Secret * Epichlorohydrin Castor Oil Based Epoxy Resin 74398-71-3 10 - 30 Trade Secret * Dimethyl Siloxane, Reaction Product With Silica 67762-90-7 0.5 - 1.5 Trade Secret * Epichlorohydrin 106-89-8 < 0.009 *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 3 of 11 Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. 5.3. Special protective actions for fire-fighters No special protective actions for fire-fighters are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with an appropriate solvent selected by a qualified and authorized person. Ventilate the area with fresh air. Read and follow safety precautions on the solvent label and SDS. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. SECTION 7: Handling and storage 7.1. Precautions for safe handling Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment. Wash contaminated clothing before reuse. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) 7.2. Conditions for safe storage including any incompatibilities Store away from acids. Store away from oxidizing agents. Store away from amines. 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 4 of 11 SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component. Ingredient C.A.S. No. Agency Limit type Additional Comments Epichlorohydrin 106-89-8 ACGIH TWA:0.5 ppm A3: Confirmed animal carcin., SKIN Epichlorohydrin 106-89-8 OSHA TWA:19 mg/m3(5 ppm) SKIN SILICA, AMORPHOUS 67762-90-7 OSHA TWA concentration:0.8 mg/m3;TWA:20 millions of particles/cu. ft. ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Indirect Vented Goggles Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Gloves made from the following material(s) are recommended: Neoprene Nitrile Rubber If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an exposure assessment. The following protective clothing material(s) are recommended: Apron - Neoprene Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 5 of 11 For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Specific Physical Form: Viscous Odor, Color, Grade: Clear viscous liquid, slight odor Odor threshold No Data Available pH Not Applicable Melting point Not Applicable Boiling Point >=200 ?F Flash Point >=200 ?F [Test Method:Closed Cup] Evaporation rate No Data Available Flammability (solid, gas) Not Applicable Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Vapor Pressure <=27 psia Vapor Density No Data Available Density 1.17 g/ml Specific Gravity 1.17 [Ref Std:WATER=1] Solubility in Water Nil Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature No Data Available Decomposition temperature No Data Available Viscosity 5,000 - 15,000 centipoise [Test Method:Brookfield] Hazardous Air Pollutants 0.014 lb HAPS/lb solids [Test Method:Calculated] Volatile Organic Compounds 1 g/l [Test Method:calculated SCAQMD rule 443.1] Volatile Organic Compounds 0.1 % weight [Test Method:calculated per CARB title 2] VOC Less H2O & Exempt Solvents 1 g/l [Test Method:calculated SCAQMD rule 443.1] SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid Not determined 10.5. Incompatible materials Strong oxidizing agents Amines Strong acids 10.6. Hazardous decomposition products 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 6 of 11 Substance Condition Aldehydes Not Specified Carbon monoxide Not Specified Carbon dioxide Not Specified Toxic Vapor, Gas, Particulate Not Specified SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Vapors released during curing may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Eye Contact: Moderate Eye Irritation: Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. Carcinogenicity: Ingredient CAS No. Class Description Regulation Epichlorohydrin 106-89-8 Grp. 2A: Probable human carc. International Agency for Research on Cancer Epichlorohydrin 106-89-8 Anticipated human carcinogen National Toxicology Program Carcinogens Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Ingestion No data available; calculated ATE >5,000 mg/kg 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Dermal Rat LD50 > 1,600 mg/kg 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Ingestion Rat LD50 > 1,000 mg/kg Epichlorohydrin Castor Oil Based Epoxy Resin Dermal Rabbit LD50 > 2,000 mg/kg Epichlorohydrin Castor Oil Based Epoxy Resin Ingestion Rat LD50 > 5,000 mg/kg Dimethyl Siloxane, Reaction Product With Silica Dermal Rabbit LD50 > 5,000 mg/kg Dimethyl Siloxane, Reaction Product With Silica Inhalation- Dust/Mist (4 hours) Rat LC50 > 0.691 mg/l Dimethyl Siloxane, Reaction Product With Silica Ingestion Rat LD50 > 5,110 mg/kg 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 7 of 11 Epichlorohydrin Dermal Rabbit LD50 755 mg/kg Epichlorohydrin Inhalation- Vapor (4 hours) Rat LC50 1.7 mg/l Epichlorohydrin Ingestion Rat LD50 260 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Rabbit Mild irritant Dimethyl Siloxane, Reaction Product With Silica Rabbit No significant irritation Epichlorohydrin Human and animal Corrosive Serious Eye Damage/Irritation Name Species Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Rabbit Moderate irritant Dimethyl Siloxane, Reaction Product With Silica Rabbit No significant irritation Epichlorohydrin Rabbit Corrosive Skin Sensitization Name Species Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Human and animal Sensitizing Dimethyl Siloxane, Reaction Product With Silica Human and animal Not classified Epichlorohydrin Human and animal Sensitizing Respiratory Sensitization Name Species Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Human Not classified Germ Cell Mutagenicity Name Route Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer In vivo Not mutagenic 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer In Vitro Some positive data exist, but the data are not sufficient for classification Dimethyl Siloxane, Reaction Product With Silica In Vitro Not mutagenic Epichlorohydrin In Vitro Some positive data exist, but the data are not sufficient for classification Epichlorohydrin In vivo Mutagenic Carcinogenicity Name Route Species Value 4,4?-Isopropylidenediphenol-Epichlorohydrin Polymer Dermal Mouse Some positive data exist, but the data are not sufficient for classification Dimethyl Siloxane, Reaction Product With Silica Not Specified Mouse Some positive data exist, but the data are not sufficient for classification Epichlorohydrin Dermal Mouse Not carcinogenic Epichlorohydrin Ingestion Rat Carcinogenic Epichlorohydrin Inhalation Rat Carcinogenic Reproductive Toxicity 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 8 of 11 Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration 4,4?-Isopropylidenediphenol- Epichlorohydrin Polymer Ingestion Not classified for female reproduction Rat NOAEL 750 mg/kg/day 2 generation 4,4?-Isopropylidenediphenol- Epichlorohydrin Polymer Ingestion Not classified for male reproduction Rat NOAEL 750 mg/kg/day 2 generation 4,4?-Isopropylidenediphenol- Epichlorohydrin Polymer Dermal Not classified for development Rabbit NOAEL 300 mg/kg/day during organogenesi s 4,4?-Isopropylidenediphenol- Epichlorohydrin Polymer Ingestion Not classified for development Rat NOAEL 750 mg/kg/day 2 generation Dimethyl Siloxane, Reaction Product With Silica Ingestion Not classified for female reproduction Rat NOAEL 509 mg/kg/day 1 generation Dimethyl Siloxane, Reaction Product With Silica Ingestion Not classified for male reproduction Rat NOAEL 497 mg/kg/day 1 generation Dimethyl Siloxane, Reaction Product With Silica Ingestion Not classified for development Rat NOAEL 1,350 mg/kg/day during organogenesi s Epichlorohydrin Inhalation Not classified for female reproduction Rat NOAEL 0.2 mg/l 10 weeks Epichlorohydrin Inhalation Not classified for development Multiple animal species NOAEL 0.09 mg/l during organogenesi s Epichlorohydrin Ingestion Not classified for development Multiple animal species NOAEL 160 mg/kg/day during gestation Epichlorohydrin Ingestion Toxic to male reproduction Rat LOAEL 6.25 mg/kg/day 23 days Epichlorohydrin Inhalation Toxic to male reproduction Rat NOAEL 0.02 mg/l 10 weeks Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Epichlorohydrin Inhalation respiratory irritation May cause respiratory irritation Human NOAEL not available occupational exposure Epichlorohydrin Inhalation liver Some positive data exist, but the data are not sufficient for classification Human NOAEL not available occupational exposure Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration 4,4?- Isopropylidenediphenol- Epichlorohydrin Polymer Dermal liver Not classified Rat NOAEL 1,000 mg/kg/day 2 years 4,4?- Isopropylidenediphenol- Epichlorohydrin Polymer Dermal nervous system Not classified Rat NOAEL 1,000 mg/kg/day 13 weeks 4,4?- Isopropylidenediphenol- Epichlorohydrin Polymer Ingestion auditory system | heart | endocrine system | hematopoietic system | liver | eyes | kidney and/or bladder Not classified Rat NOAEL 1,000 mg/kg/day 28 days Dimethyl Siloxane, Reaction Product With Silica Inhalation respiratory system | silicosis Not classified Human NOAEL Not available occupational exposure Epichlorohydrin Inhalation liver Causes damage to organs through prolonged or repeated exposure Rat NOAEL 0.21 mg/l 19 days 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 9 of 11 Epichlorohydrin Inhalation kidney and/or bladder May cause damage to organs though prolonged or repeated exposure Rat NOAEL 0.04 mg/l 136 weeks Epichlorohydrin Inhalation endocrine system Not classified Rat NOAEL 0.377 mg/l 4 weeks Epichlorohydrin Inhalation immune system Not classified Rat LOAEL 0.211 mg/l 4 weeks Epichlorohydrin Inhalation heart Not classified Rat NOAEL 0.02 mg/l 98 days Epichlorohydrin Inhalation nervous system Not classified Rat NOAEL 0.002 mg/l 98 days Epichlorohydrin Inhalation respiratory system Not classified Multiple animal species NOAEL 0.02 mg/l 13 weeks Epichlorohydrin Inhalation blood Not classified Rat NOAEL 0.189 mg/l 90 days Epichlorohydrin Ingestion heart | blood Not classified Rat NOAEL 80 mg/kg/day 12 weeks Epichlorohydrin Ingestion liver Not classified Rat NOAEL 25 mg/kg/day 90 days Aspiration Hazard For the component/components, either no data are currently available or the data are not sufficient for classification. Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: Regulatory information 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 10 of 11 15.1. US Federal Regulations Contact 3M for more information. EPCRA 311/312 Hazard Classifications: Physical Hazards Not applicable Health Hazards Serious eye damage or eye irritation 15.2. State Regulations Contact 3M for more information. California Proposition 65 Ingredient C.A.S. No. Listing Epichlorohydrin 106-89-8 Male reproductive toxin Epichlorohydrin 106-89-8 Carcinogen 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. All required components of this product are listed on the active portion of the TSCA Inventory. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 2 Flammability: 1 Instability: 1 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Document Group: 18-2290-7 Version Number: 5.00 Issue Date: 05/21/18 Supercedes Date: 07/27/17 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic 3M? Self-Leveling Seam Sealer PN 08307 Part B (Base) PN 08307 05/21/18 __________________________________________________________________________________________ Page 11 of 11 transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from3M 3M USA SDSs are available at www.3M.com