Material Safety Data Sheet 1. PRODUCT IDENTIFICATION Product Name: 84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25 ML PART 1 Item No: 202002Z Product Type: Epoxy resin 2. COMPOSITION/INFORMATION ON INGREDIENTS Component Weight% ACGIH; TLV-TWA OSHA PEL BISPHENOL A/EPICHLOROHYDRIN BASED EPOXY RESIN 25068-38-6 >90 Not listed Not listed TREATED SILICON DIOXIDE, SYNTHETIC, CRYSTALLINE-FREE 67762-90-7 <10 10 mg/m3 Not listed 3. HAZARDS IDENTIFICATION Toxicity: May cause eye, skin and respiratory irritation. May cause skin sensitization. Primary Routes of Entry: Eye and skin contact, ingestion, inhalation Signs and Symptoms of Exposure: May cause pain, redness or swelling of the eyes and excessive blinking and tear production. Repeated skin contact may cause allergic skin reactions. Contact with product at elevated temperatures can result in thermal burns. Excessive accidental exposure may cause headache, dizziness, nausea and mild respiratory irritation. Ingestion may cause nausea and vomiting. Aggravated Medical Condition: Preexisting eye, skin and respiratory disorders may be aggravated by overexposure to this product. 4. FIRST AID MEASURES Ingestion: If swallowed, DO NOT induce vomiting. Give victim water, call a physician immediately. Never give anything by mouth to an unconscious person. Inhalation: Move to fresh air in case of accidental inhalation of vapours. Oxygen or artificial respiration if needed. Skin Contact: Remove contaminated clothing. Wash area with soap and water. If irritation persists, seek medical attention. Eye Contact: In case of contact, immediately flush eyes with plenty of water for at least 15 minutes and get medical attention if irritation persists. 5. FIRE FIGHTING MEASURES Flash Point ?F(C?): >400?F PMCC Recommended Extinguishing Media: Carbon Dioxide, Dry Chemicals, Foam. Special Fire-Fighting Procedures: Material will not burn unless preheated. Firefighters should wear self- contained breathing apparatus. Use water spray to cool exposed containers. Hazardous Products of Combustion: Oxides of carbon, Aldehydes, Acid vapors Unusual Fire/Explosion Hazards: May decompose above 300 degrees F.; may polymerize above 500 degrees F. in which case closed containers may rupture or explode. Fumes and vapor from thermal and chemical decomposition vary in composition and toxicity. Do not breathe fumes. Lower Explosive Limit: Not determined Upper Explosive Limit: Not determined 6. ACCIDENTAL RELEASE MEASURES Spill Procedures: Maintain good ventilation. Take up with an inert absorbent. Store in a closed waste container until disposal. Prevent from entering waterways or sewers. 1 of 3 ITW Permatex 10 Columbus Blvd. Hartford, CT 06106 USA Telephone: 1-87-Permatex (877) 376-2839 Emergency: 800-255-3924 (ChemTel) International Emergency: +01-813-248-0585 7. HANDLING AND STORAGE Storage: Store in a cool, dry area. Store away from heat. Handling: Avoid contact with vapors from heated material. Avoid contact with skin and eyes. Wash hands before eating and smoking. Discard contaminated leather gloves and shoes. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Eyes: Safety glasses. Skin: Neoprene or nitrile gloves recommended. Wash contaminated clothing before re-use. Ventilation: General; local exhaust ventilation as necessary to control any air contaminants to within their exposure limits (or to the lowest feasible levels when limits have not been established) during the use of this product. Respiratory Protection: An approved organic vapor respirator should be worn when exposures are expected to exceed the applicable limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Clear viscous liquid Odor: Slight Boiling Point: >500?F pH: Neutral Solubility in Water: Negligible Specific Gravity: 1.16 VOC(Wt.%): 0 Vapor Pressure: 0.03 mmHg @ 171?F Vapor Density (Air=1): >1 Evaporation Rate: <1 (butyl acetate = 1) 10. STABILITY AND REACTIVITY Chemical Stability: Stable Hazardous Polymerization: Will not occur Incompatabilities: Strong Lewis or mineral acids, strong oxidizing agents, strong mineral and organic bases (especially primary and secondary aliphatic amines) Conditions to Avoid: Heat. Hazardous Products of Combustion: Oxides of carbon, Aldehydes, Acid vapors 11. TOXICOLOGICAL INFORMATION See Section 3 12. ECOLOGICAL INFORMATION No data available 13. DISPOSAL CONSIDERATIONS Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations US EPA Waste Number: NH - Not a RCRA Hazardous Waste Material 14. TRANSPORTATION INFORMATION DOT (49CFR 172) U.S. Department of Transportation - DOT - 49 CFR (Ground) DOT Shipping Name: Not regulated Hazard Class: None UN/ID Number: None IATA (Air) Proper Shipping Name: Not regulated Class or Division: None UN/ID Number: None IMDG (Vessel) Proper Shipping Name: Not regulated Hazard Class: None UN Number: None Marine Pollutant: None Item No. 202002Z84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25 ML PART 1 Product Name: 15. REGULATORY INFORMATION SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical. NONE California Proposition 65: WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory. 16. OTHER INFORMATION Estimated NFPA Rating: HEALTH 2, FLAMMABILITY 1 , REACTIVITY 0. Estimated HMIS Classification: HEALTH 2, FLAMMABILITY 1, PHYSICAL HAZARD 0 (NFPA is a registered trademark of the National Fire Protection Association) HMIS is a registered trademark of the National Paint and Coatings Association Product Name: Company: ITW Permatex 10 Columbus Blvd. Hartford, CT USA 06106 Item No. 202002Z Revision Number: 4 Telephone No.: 1-87-Permatex (877) 376-2839 Prepared By: Denise Boyd, Manager-Environmental, Health & Safety 84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25 ML PART 1 Revision Date: November 29, 2011 Material Safety Data Sheet 1. PRODUCT IDENTIFICATION Product Name: 84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25ML PART 2 Item No: PTX203014Z Product Type: Epoxy hardener 2. COMPOSITION/INFORMATION ON INGREDIENTS Component Weight% ACGIH; TLV-TWA OSHA PEL POLYAMINE-POLYMERCAPTAN BLEND Mixture _ >80 Not listed Not listed SUBSTITUTED AMIDINE 6674-22-2 <5 Not listed Not listed 2,2-OXYBIS (N,N- DIMETHYLETHANAMINE) 3033-62-3 <5 0.05 ppm Not listed 3. HAZARDS IDENTIFICATION Toxicity: May cause skin burns and corneal injury resulting in permanent impairment of vision including blindness. May cause skin sensitization. If poorly ventilated or strongly heated, can cause severe irritation of the respiratory tract including damage and scarring of tissue. Ingestion causes severe damage to mucous membranes. Aspiration hazard if swallowed. Primary Routes of Entry: Eye and skin contact, ingestion, inhalation Signs and Symptoms of Exposure: Can cause severe and painful burns on contact to eyes, skin and if taken internally. Inhalation of mist or vapor can cause damage to the upper respiratory tract and to the tissue depending on severity of exposure. Effects can range from mild irritation of mucous membranes to severe pneumonitis and destruction of lung tissue. Aggravated Medical Condition: Preexisting eye, skin and respiratory disorders may be aggravated by overexposure to this product. 4. FIRST AID MEASURES Ingestion: If swallowed, DO NOT induce vomiting. Drink water or milk. Seek medical attention immediately. Never give fluids or induce vomiting if the victim is unconscious or having convulsions. Inhalation: Move to fresh air in case of accidental inhalation of vapours. Oxygen or artificial respiration if needed. Obtain medical attention. Skin Contact: In case of contact, immediately flush skin with plenty of soap and water for at least 15 minutes. Get medical attention. Discard contaminated shoes. Eye Contact: Flush eyes with clean water for at least 20 minutes while gently holding eyelids open, lifting upper and lower lids. 5. FIRE FIGHTING MEASURES Flash Point ?F(C?): >200?F PMCC Recommended Extinguishing Media: Carbon dioxide, Dry chemical, Foam Special Fire-Fighting Procedures: Firefighters should wear self-contained breathing apparatus. Hazardous Products of Combustion: Oxides of nitrogen, Hydrogen sulfide, Oxides of sulfur, Oxides of carbon Unusual Fire/Explosion Hazards: Irritating or toxic gases or fumes may be generated by thermal decomposition or combustion. Lower Explosive Limit: Not determined Upper Explosive Limit: Not determined 6. ACCIDENTAL RELEASE MEASURES Spill Procedures: Maintain good ventilation. Take up with an inert absorbent. Store in a closed waste container until disposal. Prevent from entering waterways or sewers. Wear appropriate protective and respiratory equipment. 1 of 3 ITW Permatex 10 Columbus Blvd. Hartford, CT 06106 USA Telephone: 1-87-Permatex (877) 376-2839 Emergency: 800-255-3924 (ChemTel) International Emergency: +01-813-248-0585 7. HANDLING AND STORAGE Storage: Store away from heat. Store in a cool, dry area. Keep away from oxidizers. Handling: Avoid contact with vapors from heated material. Avoid contact with skin and eyes. Wash hands before eating and smoking. Discard contaminated leather gloves and shoes. Do not mix with sodium nitrite or other nitrosating agents as cancer-causing nitrosamines could be formed. 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Eyes: Chemical goggles; also wear a face shield if splashing hazard exists. Skin: Neoprene or nitrile gloves recommended. Wash contaminated clothing before re-use. Ventilation: General; local exhaust ventilation as necessary to control any air contaminants to within their exposure limits (or to the lowest feasible levels when limits have not been established) during the use of this product. Respiratory Protection: An approved organic vapor respirator should be worn when exposures are expected to exceed the applicable limits. 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance: Amber liquid Odor: Mercaptan Boiling Point: Not determined pH: Does not apply Solubility in Water: Dispersible Specific Gravity: 1.12 VOC(Wt.%): 0 Vapor Pressure: Not determined Vapor Density (Air=1): >1 Evaporation Rate: <1 (butyl acetate = 1) 10. STABILITY AND REACTIVITY Chemical Stability: Stable Hazardous Polymerization: Will not occur Incompatabilities: Strong oxidizers, Peroxides, Acids, Sodium/calcium hypochlorite, Nitrates Conditions to Avoid: Heat. Hazardous Products of Combustion: Oxides of nitrogen, Hydrogen sulfide, Oxides of sulfur, Oxides of carbon 11. TOXICOLOGICAL INFORMATION See Section 3 12. ECOLOGICAL INFORMATION No data available 13. DISPOSAL CONSIDERATIONS Recommended Method of Disposal: Disposal should be made in accordance with federal, state and local regulations. US EPA Waste Number: NH - Not a RCRA Hazardous Waste Material 14. TRANSPORTATION INFORMATION DOT (49CFR 172) U.S. Department of Transportation - DOT - 49 CFR (Ground) DOT Shipping Name: Consumer Commodity (not more than one liter) Hazard Class: ORM-D UN/ID Number: None IATA (Air) Proper Shipping Name: Consumer Commodity (Not more than 1 liter) Class or Division: Class 9 UN/ID Number: ID 8000 IMDG (Vessel) Proper Shipping Name: Corrosive liquid, basic, organic, n.o.s.(Mercaptan/Amine blend), Limited Quantity Hazard Class: Class 8 PGIII UN Number: UN 3267 Marine Pollutant: None Item No. PTX203014Z84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25ML PART 2 Product Name: 15. REGULATORY INFORMATION SARA 313 Chemicals: The following component(s) is listed as a SARA Section 313 Toxic Chemical. NONE California Proposition 65: WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm TSCA Inventory Status: All components of this product are listed (or exempt) on the EPA TSCA inventory. 16. OTHER INFORMATION Estimated NFPA Rating: HEALTH 3, FLAMMABILITY 1 , REACTIVITY 0. Estimated HMIS Classification: HEALTH 3, FLAMMABILITY 1, PHYSICAL HAZARD 0 (NFPA is a registered trademark of the National Fire Protection Association) HMIS is a registered trademark of the National Paint and Coatings Association Product Name: Company: ITW Permatex 10 Columbus Blvd. Hartford, CT USA 06106 Item No. PTX203014Z Revision Number: 6 84160 PERMA POXY 1 MINUTE GEN.PURPOSE EPOXY 25ML PART 2 Telephone No.: 1-87-Permatex (877) 376-2839 Prepared By: Denise Boyd, Manager-Environmental, Health & Safety Revision Date: November 29, 2011 << /ASCII85EncodePages false /AllowTransparency false /AutoPositionEPSFiles true /AutoRotatePages /All /Binding /Left /CalGrayProfile (Dot Gain 20%) /CalRGBProfile (sRGB IEC61966-2.1) /CalCMYKProfile (U.S. Web Coated \050SWOP\051 v2) /sRGBProfile (sRGB IEC61966-2.1) /CannotEmbedFontPolicy /Warning /CompatibilityLevel 1.4 /CompressObjects /Tags /CompressPages true /ConvertImagesToIndexed true /PassThroughJPEGImages true /CreateJDFFile false /CreateJobTicket false /DefaultRenderingIntent /Default /DetectBlends true /DetectCurves 0.0000 /ColorConversionStrategy /LeaveColorUnchanged /DoThumbnails false /EmbedAllFonts true /EmbedOpenType false /ParseICCProfilesInComments true /EmbedJobOptions true /DSCReportingLevel 0 /EmitDSCWarnings false /EndPage -1 /ImageMemory 1048576 /LockDistillerParams false /MaxSubsetPct 100 /Optimize true /OPM 1 /ParseDSCComments true /ParseDSCCommentsForDocInfo true /PreserveCopyPage true /PreserveDICMYKValues true /PreserveEPSInfo true /PreserveFlatness true /PreserveHalftoneInfo false /PreserveOPIComments false /PreserveOverprintSettings true /StartPage 1 /SubsetFonts true /TransferFunctionInfo /Apply /UCRandBGInfo /Preserve /UsePrologue false /ColorSettingsFile () /AlwaysEmbed [ true ] /NeverEmbed [ true ] /AntiAliasColorImages false /CropColorImages true /ColorImageMinResolution 300 /ColorImageMinResolutionPolicy /OK /DownsampleColorImages true /ColorImageDownsampleType /Bicubic /ColorImageResolution 300 /ColorImageDepth -1 /ColorImageMinDownsampleDepth 1 /ColorImageDownsampleThreshold 1.50000 /EncodeColorImages true /ColorImageFilter /DCTEncode /AutoFilterColorImages true /ColorImageAutoFilterStrategy /JPEG /ColorACSImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /ColorImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /JPEG2000ColorACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /JPEG2000ColorImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /AntiAliasGrayImages false /CropGrayImages true /GrayImageMinResolution 300 /GrayImageMinResolutionPolicy /OK /DownsampleGrayImages true /GrayImageDownsampleType /Bicubic /GrayImageResolution 300 /GrayImageDepth -1 /GrayImageMinDownsampleDepth 2 /GrayImageDownsampleThreshold 1.50000 /EncodeGrayImages true /GrayImageFilter /DCTEncode /AutoFilterGrayImages true /GrayImageAutoFilterStrategy /JPEG /GrayACSImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /GrayImageDict << /QFactor 0.15 /HSamples [1 1 1 1] /VSamples [1 1 1 1] >> /JPEG2000GrayACSImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /JPEG2000GrayImageDict << /TileWidth 256 /TileHeight 256 /Quality 30 >> /AntiAliasMonoImages false /CropMonoImages true /MonoImageMinResolution 1200 /MonoImageMinResolutionPolicy /OK /DownsampleMonoImages true /MonoImageDownsampleType /Bicubic /MonoImageResolution 1200 /MonoImageDepth -1 /MonoImageDownsampleThreshold 1.50000 /EncodeMonoImages true /MonoImageFilter /CCITTFaxEncode /MonoImageDict << /K -1 >> /AllowPSXObjects false /CheckCompliance [ /None ] /PDFX1aCheck false /PDFX3Check false /PDFXCompliantPDFOnly false /PDFXNoTrimBoxError true /PDFXTrimBoxToMediaBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXSetBleedBoxToMediaBox true /PDFXBleedBoxToTrimBoxOffset [ 0.00000 0.00000 0.00000 0.00000 ] /PDFXOutputIntentProfile () /PDFXOutputConditionIdentifier () /PDFXOutputCondition () /PDFXRegistryName () /PDFXTrapped /False /Description << /CHS /CHT /DAN /DEU /ESP /FRA /ITA /JPN /KOR /NLD (Gebruik deze instellingen om Adobe PDF-documenten te maken voor kwaliteitsafdrukken op desktopprinters en proofers. De gemaakte PDF-documenten kunnen worden geopend met Acrobat en Adobe Reader 5.0 en hoger.) /NOR /PTB /SUO /SVE /ENU (Use these settings to create Adobe PDF documents for quality printing on desktop printers and proofers. Created PDF documents can be opened with Acrobat and Adobe Reader 5.0 and later.) >> /Namespace [ (Adobe) (Common) (1.0) ] /OtherNamespaces [ << /AsReaderSpreads false /CropImagesToFrames true /ErrorControl /WarnAndContinue /FlattenerIgnoreSpreadOverrides false /IncludeGuidesGrids false /IncludeNonPrinting false /IncludeSlug false /Namespace [ (Adobe) (InDesign) (4.0) ] /OmitPlacedBitmaps false /OmitPlacedEPS false /OmitPlacedPDF false /SimulateOverprint /Legacy >> << /AddBleedMarks false /AddColorBars false /AddCropMarks false /AddPageInfo false /AddRegMarks false /ConvertColors /NoConversion /DestinationProfileName () /DestinationProfileSelector /NA /Downsample16BitImages true /FlattenerPreset << /PresetSelector /MediumResolution >> /FormElements false /GenerateStructure true /IncludeBookmarks false /IncludeHyperlinks false /IncludeInteractive false /IncludeLayers false /IncludeProfiles true /MultimediaHandling /UseObjectSettings /Namespace [ (Adobe) (CreativeSuite) (2.0) ] /PDFXOutputIntentProfileSelector /NA /PreserveEditing true /UntaggedCMYKHandling /LeaveUntagged /UntaggedRGBHandling /LeaveUntagged /UseDocumentBleed false >> ] >> setdistillerparams << /HWResolution [2400 2400] /PageSize [612.000 792.000] >> setpagedevice