Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 1 of 11 ______________________________________________________________________________________________________________________ SAFETY DATA SHEET SECTION 1 PRODUCT AND COMPANY IDENTIFICATION PRODUCT Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Product Description: Base Oil and Additives Product Code: 201520403560, 440693-00, 970529 Intended Use: Engine oil COMPANY IDENTIFICATION Supplier: EXXON MOBIL CORPORATION 22777 Springwoods Village Parkway Spring, TX 77389 USA 24 Hour Health Emergency 609-737-4411 Transportation Emergency Phone 800-424-9300 or 703-527-3887 CHEMTREC Product Technical Information 800-662-4525 MSDS Internet Address www.exxon.com, www.mobil.com SECTION 2 HAZARDS IDENTIFICATION This material is not hazardous according to regulatory guidelines (see (M)SDS Section 15). Other hazard information: HAZARD NOT OTHERWISE CLASSIFIED (HNOC): None as defined under 29 CFR 1910.1200. PHYSICAL / CHEMICAL HAZARDS No significant hazards. HEALTH HAZARDS High-pressure injection under skin may cause serious damage. Excessive exposure may result in eye, skin, or respiratory irritation. ENVIRONMENTAL HAZARDS No significant hazards. NFPA Hazard ID: Health: 0 Flammability: 1 Reactivity: 0 HMIS Hazard ID: Health: 0 Flammability: 1 Reactivity: 0 Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 2 of 11 ______________________________________________________________________________________________________________________ NOTE: This material should not be used for any other purpose than the intended use in Section 1 without expert advice. Health studies have shown that chemical exposure may cause potential human health risks which may vary from person to person. SECTION 3 COMPOSITION / INFORMATION ON INGREDIENTS This material is defined as a mixture. Hazardous Substance(s) or Complex Substance(s) required for disclosure Name CAS# Concentration* GHS Hazard Codes ALKYL PHENOL 125643-61-0 1 - < 5% H413 C14-16-18 ALKYL PHENOL 0.1 - < 1% H317, H373 SOLVENT DEWAXED HEAVY PARAFFINIC DISTILLATE 64742-65-0 1 - < 5% H304 ZINC ALKYL DITHIOPHOSPHATE 113706-15-3 0.1 - < 1% H303, H315, H318, H401, H411 * All concentrations are percent by weight unless material is a gas. Gas concentrations are in percent by volume. As per paragraph (i) of 29 CFR 1910.1200, formulation is considered a trade secret and specific chemical identity and exact percentage (concentration) of composition may have been withheld. Specific chemical identity and exact percentage composition will be provided to health professionals, employees, or designated representatives in accordance with applicable provisions of paragraph (i). SECTION 4 FIRST AID MEASURES INHALATION Remove from further exposure. For those providing assistance, avoid exposure to yourself or others. Use adequate respiratory protection. If respiratory irritation, dizziness, nausea, or unconsciousness occurs, seek immediate medical assistance. If breathing has stopped, assist ventilation with a mechanical device or use mouth-to-mouth resuscitation. SKIN CONTACT Wash contact areas with soap and water. If product is injected into or under the skin, or into any part of the body, regardless of the appearance of the wound or its size, the individual should be evaluated immediately by a physician as a surgical emergency. Even though initial symptoms from high pressure injection may be minimal or absent, early surgical treatment within the first few hours may significantly reduce the ultimate extent of injury. EYE CONTACT Flush thoroughly with water. If irritation occurs, get medical assistance. INGESTION First aid is normally not required. Seek medical attention if discomfort occurs. SECTION 5 FIRE FIGHTING MEASURES EXTINGUISHING MEDIA Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 3 of 11 ______________________________________________________________________________________________________________________ Appropriate Extinguishing Media: Use water fog, foam, dry chemical or carbon dioxide (CO2) to extinguish flames. Inappropriate Extinguishing Media: Straight Streams of Water FIRE FIGHTING Fire Fighting Instructions: Evacuate area. Prevent runoff from fire control or dilution from entering streams, sewers, or drinking water supply. Firefighters should use standard protective equipment and in enclosed spaces, self-contained breathing apparatus (SCBA). Use water spray to cool fire exposed surfaces and to protect personnel. Hazardous Combustion Products: Aldehydes, Incomplete combustion products, Oxides of carbon, Smoke, Fume, Sulfur oxides FLAMMABILITY PROPERTIES Flash Point [Method]: >215?C (419?F) [ASTM D-92] Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0 Autoignition Temperature: N/D SECTION 6 ACCIDENTAL RELEASE MEASURES NOTIFICATION PROCEDURES In the event of a spill or accidental release, notify relevant authorities in accordance with all applicable regulations. US regulations require reporting releases of this material to the environment which exceed the applicable reportable quantity or oil spills which could reach any waterway including intermittent dry creeks. The National Response Center can be reached at (800)424-8802. PROTECTIVE MEASURES Avoid contact with spilled material. See Section 5 for fire fighting information. See the Hazard Identification Section for Significant Hazards. See Section 4 for First Aid Advice. See Section 8 for advice on the minimum requirements for personal protective equipment. Additional protective measures may be necessary, depending on the specific circumstances and/or the expert judgment of the emergency responders. For emergency responders: Respiratory protection: respiratory protection will be necessary only in special cases, e.g., formation of mists. Half-face or full-face respirator with filter(s) for dust/organic vapor or Self Contained Breathing Apparatus (SCBA) can be used depending on the size of spill and potential level of exposure. If the exposure cannot be completely characterized or an oxygen deficient atmosphere is possible or anticipated, SCBA is recommended. Work gloves that are resistant to hydrocarbons are recommended. Gloves made of polyvinyl acetate (PVA) are not water-resistant and are not suitable for emergency use. Chemical goggles are recommended if splashes or contact with eyes is possible. Small spills: normal antistatic work clothes are usually adequate. Large spills: full body suit of chemical resistant, antistatic material is recommended. SPILL MANAGEMENT Land Spill: Stop leak if you can do it without risk. Recover by pumping or with suitable absorbent. Water Spill: Stop leak if you can do it without risk. Confine the spill immediately with booms. Warn other shipping. Remove from the surface by skimming or with suitable absorbents. Seek the advice of a specialist before using dispersants. Water spill and land spill recommendations are based on the most likely spill scenario for this material; Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 4 of 11 ______________________________________________________________________________________________________________________ however, geographic conditions, wind, temperature, (and in the case of a water spill) wave and current direction and speed may greatly influence the appropriate action to be taken. For this reason, local experts should be consulted. Note: Local regulations may prescribe or limit action to be taken. ENVIRONMENTAL PRECAUTIONS Large Spills: Dike far ahead of liquid spill for later recovery and disposal. Prevent entry into waterways, sewers, basements or confined areas. SECTION 7 HANDLING AND STORAGE HANDLING Avoid contact with used product. Prevent small spills and leakage to avoid slip hazard. Material can accumulate static charges which may cause an electrical spark (ignition source). When the material is handled in bulk, an electrical spark could ignite any flammable vapors from liquids or residues that may be present (e.g., during switch-loading operations). Use proper bonding and/or ground procedures. However, bonding and grounds may not eliminate the hazard from static accumulation. Consult local applicable standards for guidance. Additional references include American Petroleum Institute 2003 (Protection Against Ignitions Arising out of Static, Lightning and Stray Currents) or National Fire Protection Agency 77 (Recommended Practice on Static Electricity) or CENELEC CLC/TR 50404 (Electrostatics - Code of practice for the avoidance of hazards due to static electricity). Static Accumulator: This material is a static accumulator. STORAGE The type of container used to store the material may affect static accumulation and dissipation. Do not store in open or unlabelled containers. SECTION 8 EXPOSURE CONTROLS / PERSONAL PROTECTION EXPOSURE LIMIT VALUES Exposure limits/standards (Note: Exposure limits are not additive) Substance Name Form Limit / Standard NOTE Source SOLVENT DEWAXED HEAVY PARAFFINIC DISTILLATE Mist. TWA 5 mg/m3 N/A OSHA Z1 SOLVENT DEWAXED HEAVY PARAFFINIC DISTILLATE Inhalable fraction. TWA 5 mg/m3 N/A ACGIH Exposure limits/standards for materials that can be formed when handling this product: When mists/aerosols can occur the following are recommended: 5 mg/m? - ACGIH TLV (inhalable fraction), 5 mg/m? - OSHA PEL. NOTE: Limits/standards shown for guidance only. Follow applicable regulations. No biological limits allocated. ENGINEERING CONTROLS The level of protection and types of controls necessary will vary depending upon potential exposure conditions. Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 5 of 11 ______________________________________________________________________________________________________________________ Control measures to consider: No special requirements under ordinary conditions of use and with adequate ventilation. PERSONAL PROTECTION Personal protective equipment selections vary based on potential exposure conditions such as applications, handling practices, concentration and ventilation. Information on the selection of protective equipment for use with this material, as provided below, is based upon intended, normal usage. Respiratory Protection: If engineering controls do not maintain airborne contaminant concentrations at a level which is adequate to protect worker health, an approved respirator may be appropriate. Respirator selection, use, and maintenance must be in accordance with regulatory requirements, if applicable. Types of respirators to be considered for this material include: No special requirements under ordinary conditions of use and with adequate ventilation. For high airborne concentrations, use an approved supplied-air respirator, operated in positive pressure mode. Supplied air respirators with an escape bottle may be appropriate when oxygen levels are inadequate, gas/vapor warning properties are poor, or if air purifying filter capacity/rating may be exceeded. Hand Protection: Any specific glove information provided is based on published literature and glove manufacturer data. Glove suitability and breakthrough time will differ depending on the specific use conditions. Contact the glove manufacturer for specific advice on glove selection and breakthrough times for your use conditions. Inspect and replace worn or damaged gloves. The types of gloves to be considered for this material include: No protection is ordinarily required under normal conditions of use. Eye Protection: If contact is likely, safety glasses with side shields are recommended. Skin and Body Protection: Any specific clothing information provided is based on published literature or manufacturer data. The types of clothing to be considered for this material include: No skin protection is ordinarily required under normal conditions of use. In accordance with good industrial hygiene practices, precautions should be taken to avoid skin contact. Specific Hygiene Measures: Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Discard contaminated clothing and footwear that cannot be cleaned. Practice good housekeeping. ENVIRONMENTAL CONTROLS Comply with applicable environmental regulations limiting discharge to air, water and soil. Protect the environment by applying appropriate control measures to prevent or limit emissions. SECTION 9 PHYSICAL AND CHEMICAL PROPERTIES Note: Physical and chemical properties are provided for safety, health and environmental considerations only and may not fully represent product specifications. Contact the Supplier for additional information. GENERAL INFORMATION Physical State: Liquid Color: Brown Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 6 of 11 ______________________________________________________________________________________________________________________ Odor: Characteristic Odor Threshold: N/D IMPORTANT HEALTH, SAFETY, AND ENVIRONMENTAL INFORMATION Relative Density (at 15 ?C): 0.875 Flammability (Solid, Gas): N/A Flash Point [Method]: >215?C (419?F) [ASTM D-92] Flammable Limits (Approximate volume % in air): LEL: 0.9 UEL: 7.0 Autoignition Temperature: N/D Boiling Point / Range: > 316?C (600?F) Decomposition Temperature: N/D Vapor Density (Air = 1): > 2 at 101 kPa Vapor Pressure: < 0.013 kPa (0.1 mm Hg) at 20 ?C Evaporation Rate (n-butyl acetate = 1): N/D pH: N/A Log Pow (n-Octanol/Water Partition Coefficient): > 3.5 Solubility in Water: Negligible Viscosity: 109 cSt (109 mm2/sec) at 40 ?C | 14.1 cSt (14.1 mm2/sec) at 100?C [ASTM D 445] Oxidizing Properties: See Hazards Identification Section. OTHER INFORMATION Freezing Point: N/D Melting Point: N/A Pour Point: -27?C (-17?F) DMSO Extract (mineral oil only), IP-346: < 3 %wt SECTION 10 STABILITY AND REACTIVITY REACTIVITY: See sub-sections below. STABILITY: Material is stable under normal conditions. CONDITIONS TO AVOID: Excessive heat. High energy sources of ignition. MATERIALS TO AVOID: Strong oxidizers HAZARDOUS DECOMPOSITION PRODUCTS: Material does not decompose at ambient temperatures. POSSIBILITY OF HAZARDOUS REACTIONS: Hazardous polymerization will not occur. SECTION 11 TOXICOLOGICAL INFORMATION INFORMATION ON TOXICOLOGICAL EFFECTS Hazard Class Conclusion / Remarks Inhalation Acute Toxicity: No end point data for material. Minimally Toxic. Based on assessment of the components. Irritation: No end point data for material. Negligible hazard at ambient/normal handling temperatures. Ingestion Acute Toxicity: No end point data for Minimally Toxic. Based on assessment of the components. Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 7 of 11 ______________________________________________________________________________________________________________________ material. Skin Acute Toxicity: No end point data for material. Minimally Toxic. Based on assessment of the components. Skin Corrosion/Irritation: No end point data for material. Negligible irritation to skin at ambient temperatures. Based on assessment of the components. Eye Serious Eye Damage/Irritation: No end point data for material. May cause mild, short-lasting discomfort to eyes. Based on assessment of the components. Sensitization Respiratory Sensitization: No end point data for material. Not expected to be a respiratory sensitizer. Skin Sensitization: No end point data for material. Not expected to be a skin sensitizer. Based on assessment of the components. Aspiration: Data available. Not expected to be an aspiration hazard. Based on physico- chemical properties of the material. Germ Cell Mutagenicity: No end point data for material. Not expected to be a germ cell mutagen. Based on assessment of the components. Carcinogenicity: No end point data for material. Not expected to cause cancer. Based on assessment of the components. Reproductive Toxicity: No end point data for material. Not expected to be a reproductive toxicant. Based on assessment of the components. Lactation: No end point data for material. Not expected to cause harm to breast-fed children. Specific Target Organ Toxicity (STOT) Single Exposure: No end point data for material. Not expected to cause organ damage from a single exposure. Repeated Exposure: No end point data for material. Not expected to cause organ damage from prolonged or repeated exposure. Based on assessment of the components. OTHER INFORMATION For the product itself: Component concentrations in this formulation would not be expected to cause skin sensitization, based on tests of the components, this formulation, or similar formulations. Diesel engine oils: Not carcinogenic in animals tests. Used and unused diesel engine oils did not produce any carcinogenic effects in chronic mouse skin painting studies. Oils that are used in gasoline engines may become hazardous and display the following properties: Carcinogenic in animal tests. Caused mutations in vitro. Possible allergen and photoallergen. Contains polycyclic aromatic compounds (PAC) from combustion products of gasoline and/or thermal degradation products. Contains: Base oil severely refined: Not carcinogenic in animal studies. Representative material passes IP-346, Modified Ames test, and/or other screening tests. Dermal and inhalation studies showed minimal effects; lung non-specific infiltration of immune cells, oil deposition and minimal granuloma formation. Not sensitizing in test animals. The following ingredients are cited on the lists below: None. --REGULATORY LISTS SEARCHED-- Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 8 of 11 ______________________________________________________________________________________________________________________ 1 = NTP CARC 3 = IARC 1 5 = IARC 2B 2 = NTP SUS 4 = IARC 2A 6 = OSHA CARC SECTION 12 ECOLOGICAL INFORMATION The information given is based on data for the material, components of the material, or for similar materials, through the application of bridging principals. ECOTOXICITY Material -- Not expected to be harmful to aquatic organisms. MOBILITY Base oil component -- Low solubility and floats and is expected to migrate from water to the land. Expected to partition to sediment and wastewater solids. PERSISTENCE AND DEGRADABILITY Biodegradation: Base oil component -- Expected to be inherently biodegradable BIOACCUMULATION POTENTIAL Base oil component -- Has the potential to bioaccumulate, however metabolism or physical properties may reduce the bioconcentration or limit bioavailability. SECTION 13 DISPOSAL CONSIDERATIONS Disposal recommendations based on material as supplied. Disposal must be in accordance with current applicable laws and regulations, and material characteristics at time of disposal. DISPOSAL RECOMMENDATIONS Product is suitable for burning in an enclosed controlled burner for fuel value or disposal by supervised incineration at very high temperatures to prevent formation of undesirable combustion products. REGULATORY DISPOSAL INFORMATION RCRA Information: The unused product, in our opinion, is not specifically listed by the EPA as a hazardous waste (40 CFR, Part 261D), nor is it formulated to contain materials which are listed as hazardous wastes. It does not exhibit the hazardous characteristics of ignitability, corrositivity or reactivity and is not formulated with contaminants as determined by the Toxicity Characteristic Leaching Procedure (TCLP). However, used product may be regulated. Empty Container Warning Empty Container Warning (where applicable): Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 9 of 11 ______________________________________________________________________________________________________________________ SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. SECTION 14 TRANSPORT INFORMATION LAND (DOT): Not Regulated for Land Transport LAND (TDG): Not Regulated for Land Transport SEA (IMDG): Not Regulated for Sea Transport according to IMDG-Code Marine Pollutant: No AIR (IATA): Not Regulated for Air Transport SECTION 15 REGULATORY INFORMATION OSHA HAZARD COMMUNICATION STANDARD: This material is not considered hazardous in accordance with OSHA HazCom 2012, 29 CFR 1910.1200. Listed or exempt from listing/notification on the following chemical inventories: DSL, ENCS, ISHL, PICCS, TSCA Special Cases: Inventory Status AICS Restrictions Apply IECSC Restrictions Apply KECI Restrictions Apply TCSI Restrictions Apply SARA 302: No chemicals in this material are subject to the reporting requirements of SARA Title III, Section 302 SARA (311/312) REPORTABLE GHS HAZARD CLASSES: None. SARA (313) TOXIC RELEASE INVENTORY: This material contains no chemicals subject to the supplier notification requirements of the SARA 313 Toxic Release Program. The following ingredients are cited on the lists below: Chemical Name CAS Number List Citations SEVERELY HYDROTREATED 64742-54-7 17, 18, 19 Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 10 of 11 ______________________________________________________________________________________________________________________ HEAVY PARAFFINIC DISTILLATE ZINC ALKYL DITHIOPHOSPHATE 113706-15-3 15 --REGULATORY LISTS SEARCHED-- 1 = ACGIH ALL 6 = TSCA 5a2 11 = CA P65 REPRO 16 = MN RTK 2 = ACGIH A1 7 = TSCA 5e 12 = CA RTK 17 = NJ RTK 3 = ACGIH A2 8 = TSCA 6 13 = IL RTK 18 = PA RTK 4 = OSHA Z 9 = TSCA 12b 14 = LA RTK 19 = RI RTK 5 = TSCA 4 10 = CA P65 CARC 15 = MI 293 Code key: CARC=Carcinogen; REPRO=Reproductive SECTION 16 OTHER INFORMATION N/D = Not determined, N/A = Not applicable KEY TO THE H-CODES CONTAINED IN SECTION 3 OF THIS DOCUMENT (for information only): H303: May be harmful if swallowed; Acute Tox Oral, Cat 5 H304: May be fatal if swallowed and enters airways; Aspiration, Cat 1 H315: Causes skin irritation; Skin Corr/Irritation, Cat 2 H317: May cause allergic skin reaction; Skin Sensitization, Cat 1 H318: Causes serious eye damage; Serious Eye Damage/Irr, Cat 1 H373: May cause damage to organs through prolonged or repeated exposure; Target Organ, Repeated, Cat 2 H401: Toxic to aquatic life; Acute Env Tox, Cat 2 H411: Toxic to aquatic life with long lasting effects; Chronic Env Tox, Cat 2 H413: May cause long lasting harmful effects to aquatic life; Chronic Env Tox, Cat 4 THIS SAFETY DATA SHEET CONTAINS THE FOLLOWING REVISIONS: Composition: Component Table information was modified. Section 08: Exposure Limits Table information was modified. Section 09: Viscosity information was modified. Section 11 Acute Toxicity data - Header information was deleted. Section 11 Substance Name - Header information was deleted. Section 11 Substance Toxicity table - Header information was deleted. Section 11 Substance Toxicology table information was deleted. Section 15: List Citations Table information was modified. Section 15: National Chemical Inventory Listing information was modified. Section 15: Special Cases Table information was modified. Section 16: HCode Key information was modified. Section 16: MSN, MAT ID information was modified. ----------------------------------------------------------------------------------------------------------------------------------------------------- The information and recommendations contained herein are, to the best of ExxonMobil's knowledge and belief, accurate and reliable as of the date issued. You can contact ExxonMobil to insure that this document is the most current available from ExxonMobil. The information and recommendations are offered for the user's consideration and examination. It is the user's responsibility to satisfy itself that the product is suitable for the intended use. If buyer repackages this product, it is the user's responsibility to insure proper health, safety and other necessary information is Product Name: MOBIL DELVAC 1300 SUPER 15W-40 Revision Date: 19 Aug 2019 Page 11 of 11 ______________________________________________________________________________________________________________________ included with and/or on the container. Appropriate warnings and safe-handling procedures should be provided to handlers and users. Alteration of this document is strictly prohibited. Except to the extent required by law, re- publication or retransmission of this document, in whole or in part, is not permitted. The term, "ExxonMobil" is used for convenience, and may include any one or more of ExxonMobil Chemical Company, Exxon Mobil Corporation, or any affiliates in which they directly or indirectly hold any interest. ----------------------------------------------------------------------------------------------------------------------------------------------------- Internal Use Only MHC: 0B, 0B, 0, 0, 0, 0 PPEC: A DGN: 2003305XUS (1029203) ----------------------------------------------------------------------------------------------------------------------------------------------------- Copyright 2002 Exxon Mobil Corporation, All rights reserved