G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 1 of 10 Safety Data Sheet Copyright,2019Meguiar's, Inc. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing Meguiar's, Inc. products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from Meguiar's, Inc., and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 32-5654-2 Version Number: 2.01 Issue Date: 01/09/19 Supercedes Date: 01/05/18 SECTION 1: Identification 1.1. Product identifier G162, Ultimate Interior Detailer (23-177E): G16216 Product Identification Numbers 14-1000-9044-9 1.2. Recommended use and restrictions on use Recommended use Automotive, Clean interior automotive surfaces 1.3. Supplier?s details MANUFACTURER: Meguiar's, Inc. DIVISION: Meguiar's ADDRESS: 17991 Mitchell South, Irvine, CA 92614, USA Telephone: 949-752-8000 (Fax: 949-752-5784) 1.4. Emergency telephone number CHEMTREC 1-800-424-9300 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Skin Sensitizer: Category 1. Reproductive Toxicity: Category 2. 2.2. Label elements Signal word Warning G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 2 of 10 Symbols Exclamation mark | Health Hazard | Pictograms Hazard Statements May cause an allergic skin reaction. Suspected of damaging fertility or the unborn child. Precautionary Statements General: Keep out of reach of children. Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Wear protective gloves. Contaminated work clothing must not be allowed out of the workplace. Response: IF ON SKIN: Wash with plenty of soap and water. If skin irritation or rash occurs: Get medical advice/attention. Wash contaminated clothing before reuse. IF exposed or concerned: Get medical advice/attention. Storage: Store locked up. Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international regulations. 2% of the mixture consists of ingredients of unknown acute oral toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt 2-AMINOISOBUTANOL 124-68-5 < 0.5 Trade Secret * Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol- 2-yl)-5-(1,1-dimethylethyl)-4-hydroxyphenyl]-1- oxopropyl]-.omega.-hydroxy- 104810-48-2 < 0.15 Trade Secret * Polymeric Benzotriazole 104810-47-1 < 0.15 Trade Secret * Any remaining components do not contribute to the hazards of this material. *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 3 of 10 SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. Eye Contact: Flush eyes with large amounts of water. If signs/symptoms persist, get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media Material will not burn. 5.2. Special hazards arising from the substance or mixture None inherent in this product. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion 5.3. Special protective actions for fire-fighters No special protective actions for fire-fighters are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with water. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 4 of 10 SECTION 7: Handling and storage 7.1. Precautions for safe handling Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Avoid release to the environment. Wash contaminated clothing before reuse. Use personal protective equipment (gloves, respirators, etc.) as required. 7.2. Conditions for safe storage including any incompatibilities Store away from heat. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits No occupational exposure limit values exist for any of the components listed in Section 3 of this SDS. 8.2. Exposure controls 8.2.1. Engineering controls Use in a well-ventilated area. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Note: Nitrile gloves may be worn over polymer laminate gloves to improve dexterity. Gloves made from the following material(s) are recommended: Polymer laminate If this product is used in a manner that presents a higher potential for exposure (eg. spraying, high splash potential etc.), then use of protective coveralls may be necessary. Select and use body protection to prevent contact based on the results of an exposure assessment. The following protective clothing material(s) are recommended: Apron - polymer laminate Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 5 of 10 SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Odor, Color, Grade: White to translucent; Citrus odor Odor threshold No Data Available pH 9.5 - 10.5 Melting point No Data Available Boiling Point 212 ?F Flash Point No flash point [Test Method:Closed Cup] Evaporation rate No Data Available Flammability (solid, gas) Not Applicable Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Vapor Pressure No Data Available Vapor Pressure No Data Available Vapor Density No Data Available Density 0.99 g/ml Specific Gravity 0.99 [Ref Std:WATER=1] Solubility In Water No Data Available Solubility in Water Complete Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature No Data Available Decomposition temperature No Data Available Viscosity No Data Available Molecular weight No Data Available Volatile Organic Compounds 0 % weight [Test Method:calculated per CARB title 2] Volatile Organic Compounds 44 g/l [Test Method:calculated SCAQMD rule 443.1] VOC Less H2O & Exempt Solvents 77 g/l [Test Method:calculated SCAQMD rule 443.1] SECTION 10: Stability and reactivity 10.1. Reactivity This material is considered to be non reactive under normal use conditions. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid Heat 10.5. Incompatible materials None known. 10.6. Hazardous decomposition products Substance Condition None known. Refer to section 5.2 for hazardous decomposition products during combustion. G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 6 of 10 Name Route Species Value Overall product Ingestion No data available; calculated ATE >5,000 mg/kg 2-AMINOISOBUTANOL Dermal Rabbit LD50 > 2,000 mg/kg 2-AMINOISOBUTANOL Ingestion Rat LD50 2,900 mg/kg Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5- (1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.- hydroxy- Dermal Rat LD50 > 2,000 mg/kg Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5- (1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.- hydroxy- Inhalation- Dust/Mist (4 hours) Rat LC50 > 5.8 mg/l Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5- (1,1-dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.- hydroxy- Ingestion Rat LD50 > 5,000 mg/kg Polymeric Benzotriazole Dermal Rat LD50 > 2,000 mg/kg Polymeric Benzotriazole Inhalation- Dust/Mist Rat LC50 > 5.8 mg/l SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: No known health effects. Skin Contact: Contact with the skin during product use is not expected to result in significant irritation. Allergic Skin Reaction (non-photo induced): Signs/symptoms may include redness, swelling, blistering, and itching. Eye Contact: Sprayed material may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. May cause additional health effects (see below). Additional Health Effects: Reproductive/Developmental Toxicity: Contains a chemical or chemicals which can cause birth defects or other reproductive harm. Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 7 of 10 Name Route Target Organ(s) Value Species Test Result Exposure Duration (4 hours) Polymeric Benzotriazole Ingestion Rat LD50 > 5,000 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value 2-AMINOISOBUTANOL Rabbit Irritant Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1- dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.-hydroxy- Rabbit No significant irritation Polymeric Benzotriazole Rabbit No significant irritation Serious Eye Damage/Irritation Name Species Value 2-AMINOISOBUTANOL Rabbit Corrosive Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1- dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.-hydroxy- Rabbit No significant irritation Polymeric Benzotriazole Rabbit No significant irritation Skin Sensitization Name Species Value 2-AMINOISOBUTANOL Guinea pig Not classified Poly(oxy-1,2-ethanediyl), .alpha.-[3-[3-(2H-benzotriazol-2-yl)-5-(1,1- dimethylethyl)-4-hydroxyphenyl]-1-oxopropyl]-.omega.-hydroxy- Guinea pig Sensitizing Polymeric Benzotriazole Guinea pig Sensitizing Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value 2-AMINOISOBUTANOL In Vitro Not mutagenic 2-AMINOISOBUTANOL In vivo Not mutagenic Carcinogenicity For the component/components, either no data are currently available or the data are not sufficient for classification. Reproductive Toxicity Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration 2-AMINOISOBUTANOL Ingestion Not classified for female reproduction Rat NOAEL 1,000 mg/kg/day premating into lactation 2-AMINOISOBUTANOL Ingestion Not classified for male reproduction Rat NOAEL 1,000 mg/kg/day 37 days 2-AMINOISOBUTANOL Dermal Not classified for development Rat NOAEL 300 mg/kg/day during gestation 2-AMINOISOBUTANOL Ingestion Toxic to development Rat NOAEL 100 mg/kg/day premating into lactation Target Organ(s) Specific Target Organ Toxicity - single exposure G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 8 of 10 2-AMINOISOBUTANOL Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification Mouse NOAEL Not available Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration 2-AMINOISOBUTANOL Ingestion liver Some positive data exist, but the data are not sufficient for classification Rat NOAEL 23 mg/kg/day 90 days 2-AMINOISOBUTANOL Ingestion blood | eyes | kidney and/or bladder Not classified Dog NOAEL 2.8 mg/kg/day 1 years Aspiration Hazard For the component/components, either no data are currently available or the data are not sufficient for classification. Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Dispose of waste product in a permitted industrial waste facility. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information General Transportation Statement: This product does not require classification by DOT, IATA, ICAO or IMDG. Please contact the emergency numbers listed on the first page of the SDS for Transportation Information for this material. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact manufacturer for more information EPCRA 311/312 Hazard Classifications: Physical Hazards G162, Ultimate Interior Detailer (23-177E): G16216 01/09/19 Page 9 of 10 Not applicable Health Hazards Reproductive toxicity Respiratory or Skin Sensitization 15.2. State Regulations Contact manufacturer for more information 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. Contact manufacturer for more information 15.4. International Regulations Contact manufacturer for more information This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 2 Flammability: 0 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Document Group: 32-5654-2 Version Number: 2.01 Issue Date: 01/09/19 Supercedes Date: 01/05/18 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.Meguiar's, Inc.MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether theMeguiar's, Inc.product is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of aMeguiar's, Inc.product, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate theMeguiar's, Inc.product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. Meguiar's, Inc.provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information,Meguiar's, Inc.makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly fromMeguiar's, Inc. Meguiar's, Inc. USA SDSs are available at www.Meguiars.com