M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 1 of 9 Safety Data Sheet Copyright,2017Meguiar's, Inc. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing Meguiar's, Inc. products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from Meguiar's, Inc., and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 28-6043-5 Version Number: 2.01 Issue Date: 09/26/17 Supercedes Date: 03/20/15 SECTION 1: Identification 1.1. Product identifier M04, Heavy Cut Cleaner (11-83B): M0416 Product Identification Numbers 14-1000-1154-4, 14-1000-1155-1 1.2. Recommended use and restrictions on use Recommended use Automotive, Removes deep swirls, scratches, severe oxidation, alkaline and acid rain etching 1.3. Supplier?s details MANUFACTURER: Meguiar's, Inc. DIVISION: Meguiar's ADDRESS: 17991 Mitchell South, Irvine, CA 92614, USA Telephone: 949-752-8000 (Fax: 949-752-5784) 1.4. Emergency telephone number CHEMTREC 1-800-424-9300 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200. 2.2. Label elements Signal word Not applicable. Symbols Not applicable. M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 2 of 9 Pictograms Not applicable. 2.3. Hazards not otherwise classified 2% of the mixture consists of ingredients of unknown acute oral toxicity. 2% of the mixture consists of ingredients of unknown acute dermal toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Water 7732-18-5 50 - 70 Trade Secret * Aluminum Oxide (non-fibrous) 1344-28-1 10 - 30 Trade Secret * Light Petroleum Distillates 64742-14-9 10 - 30 Trade Secret * White Mineral Oil 8042-47-5 1 - 5 Trade Secret * Processed Castor Oil Trade Secret* 1 - 5 Trade Secret * Sorbitan Sesquioleate 8007-43-0 0.5 - 1.5 Trade Secret * *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Wash with soap and water. If signs/symptoms develop, get medical attention. Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a carbon dioxide or dry chemical extinguisher to extinguish. 5.2. Special hazards arising from the substance or mixture Closed containers exposed to heat from fire may build pressure and explode. M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 3 of 9 Ingredient C.A.S. No. Agency Limit type Additional Comments Aluminum Oxide (non-fibrous) 1344-28-1 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion Irritant Vapors or Gases During Combustion 5.3. Special protective actions for fire-fighters Water may not effectively extinguish fire; however, it should be used to keep fire-exposed containers and surfaces cool and prevent explosive rupture. Wear full protective clothing, including helmet, self-contained, positive pressure or pressure demand breathing apparatus, bunker coat and pants, bands around arms, waist and legs, face mask, and protective covering for exposed areas of the head. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. For large spill, or spills in confined spaces, provide mechanical ventilation to disperse or exhaust vapors, in accordance with good industrial hygiene practice. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 6.2. Environmental precautions Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Clean up residue with detergent and water. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. SECTION 7: Handling and storage 7.1. Precautions for safe handling Avoid breathing of dust created by cutting, sanding, grinding or machining. Keep out of reach of children. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) 7.2. Conditions for safe storage including any incompatibilities Store away from acids. Store away from strong bases. Store away from oxidizing agents. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component. M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 4 of 9 Aluminum, insoluble compounds 1344-28-1 ACGIH TWA(respirable fraction):1 mg/m3 A4: Not class. as human carcin MINERAL OILS, HIGHLY- REFINED OILS 8042-47-5 ACGIH TWA(inhalable fraction):5 mg/m3 A4: Not class. as human carcin Paraffin oil 8042-47-5 OSHA TWA(as mist):5 mg/m3 ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. 8.2.2. Personal protective equipment (PPE) Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Note: Nitrile gloves may be worn over polymer laminate gloves to improve dexterity. Gloves made from the following material(s) are recommended: Polymer laminate Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Odor, Color, Grade: Sweet odor; White, viscous, semi-pourable liquid Odor threshold No Data Available pH Not Applicable Melting point Not Applicable Boiling Point 390 ?F Flash Point > 200 ?F [Test Method:Pensky-Martens Closed Cup] [Details:D93-90] Flash Point Flash point > 93 ?C (200 ?F) M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 5 of 9 Evaporation rate No Data Available Flammability (solid, gas) Not Applicable Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Vapor Pressure No Data Available Vapor Density No Data Available Density 1.00 g/cm3 Specific Gravity 1.00 [Ref Std:WATER=1] Solubility in Water Moderate Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature No Data Available Decomposition temperature No Data Available Viscosity 7,000 - 16,000 centipoise Volatile Organic Compounds 16.15 % weight VOC Less H2O & Exempt Solvents 438.91 g/l SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid Temperatures above the boiling point 10.5. Incompatible materials Strong acids Strong bases Strong oxidizing agents 10.6. Hazardous decomposition products Substance Condition None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 6 of 9 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Mild Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, and dryness. Eye Contact: Dust created by cutting, grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Dermal No data available; calculated ATE >5,000 mg/kg Overall product Ingestion No data available; calculated ATE >5,000 mg/kg Aluminum Oxide (non-fibrous) Dermal LD50 estimated to be > 5,000 mg/kg Aluminum Oxide (non-fibrous) Inhalation- Dust/Mist (4 hours) Rat LC50 > 2.3 mg/l Aluminum Oxide (non-fibrous) Ingestion Rat LD50 > 5,000 mg/kg Light Petroleum Distillates Dermal Rabbit LD50 > 2,000 mg/kg Light Petroleum Distillates Ingestion Rat LD50 > 5,000 mg/kg White Mineral Oil Dermal Rabbit LD50 > 2,000 mg/kg White Mineral Oil Ingestion Rat LD50 > 5,000 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value Aluminum Oxide (non-fibrous) Rabbit No significant irritation Light Petroleum Distillates Professional judgement Mild irritant White Mineral Oil Rabbit No significant irritation Serious Eye Damage/Irritation Name Species Value Aluminum Oxide (non-fibrous) Rabbit No significant irritation Light Petroleum Distillates Professional judgement Mild irritant White Mineral Oil Rabbit Mild irritant Skin Sensitization Name Species Value Light Petroleum Distillates Guinea pig Not classified White Mineral Oil Guinea pig Not classified M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 7 of 9 Name Route Target Organ(s) Value Species Test Result Exposure Duration Aluminum Oxide (non- fibrous) Inhalation pneumoconiosis Some positive data exist, but the data are not sufficient for classification Human NOAEL Not available occupational exposure Aluminum Oxide (non- fibrous) Inhalation pulmonary fibrosis Not classified Human NOAEL Not available occupational exposure White Mineral Oil Ingestion hematopoietic system Not classified Rat NOAEL 1,381 90 days Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value Aluminum Oxide (non-fibrous) In Vitro Not mutagenic Light Petroleum Distillates In Vitro Not mutagenic White Mineral Oil In Vitro Not mutagenic Carcinogenicity Name Route Species Value Aluminum Oxide (non-fibrous) Inhalation Rat Not carcinogenic Light Petroleum Distillates Dermal Mouse Some positive data exist, but the data are not sufficient for classification White Mineral Oil Dermal Mouse Not carcinogenic White Mineral Oil Inhalation Multiple animal species Not carcinogenic Reproductive Toxicity Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration White Mineral Oil Ingestion Not classified for female reproduction Rat NOAEL 4,350 mg/kg/day 13 weeks White Mineral Oil Ingestion Not classified for male reproduction Rat NOAEL 4,350 mg/kg/day 13 weeks White Mineral Oil Ingestion Not classified for development Rat NOAEL 4,350 mg/kg/day during gestation Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Light Petroleum Distillates Inhalation central nervous system depression May cause drowsiness or dizziness Human and animal NOAEL Not available Light Petroleum Distillates Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification NOAEL Not available Light Petroleum Distillates Ingestion central nervous system depression May cause drowsiness or dizziness Professional judgement NOAEL Not available Specific Target Organ Toxicity - repeated exposure M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 8 of 9 mg/kg/day White Mineral Oil Ingestion liver | immune system Not classified Rat NOAEL 1,336 mg/kg/day 90 days Aspiration Hazard Name Value Light Petroleum Distillates Aspiration hazard White Mineral Oil Aspiration hazard Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Prior to disposal, consult all applicable authorities and regulations to insure proper classification. Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty and clean product containers may be disposed as non-hazardous waste. Consult your specific regulations and service providers to determine available options and requirements. SECTION 14: Transport Information General Transportation Statement: This product does not require classification by DOT, IATA, ICAO or IMDG. Please contact the emergency numbers listed on the first page of the SDS for Transportation Information for this material. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact manufacturer for more information 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - Yes Delayed Hazard - No EPCRA 311/312 Hazard Classifications (effective January 1, 2018): Physical Hazards Not applicable M04, Heavy Cut Cleaner (11-83B): M0416 09/26/17 Page 9 of 9 Health Hazards Not applicable 15.2. State Regulations Contact manufacturer for more information 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. Contact manufacturer for more information 15.4. International Regulations Contact manufacturer for more information This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 1 Flammability: 1 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. Document Group: 28-6043-5 Version Number: 2.01 Issue Date: 09/26/17 Supercedes Date: 03/20/15 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. Meguiar's, Inc. MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the Meguiar's, Inc. product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a Meguiar's, Inc. product, some of which are uniquely within the user's knowledge and control ,it is essential that the user evaluate the Meguiar's, Inc. product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. Meguiar's, Inc. provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, Meguiar's, Inc. makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from Meguiar's, Inc. Meguiar's, Inc. USA SDSs are available at www.Meguiars.com