FVP Full Synthetic 0W-16 Not available. Liquid. GHS product identifier Other means of identification Product type Emergency telephone number Section 1. Identification : : : : Supplier's details Factory Motor Parts 1380 Corporate Center Curve, Suite 200 Eagan, MN 55121 USA 866-3887-3343 INFOTRAC 1-800-535-5053 FVP Full Synthetic 0W-16 Safety Data Sheet Relevant identified uses of the substance or mixture and uses advised against Identified uses None known. Uses advised against Reason Product code : 303033150000 Not applicable. Section 2. Hazards identification Not classified.Classification of the substance or mixture : Signal word : Hazard statements : No known significant effects or critical hazards. Precautionary statements Prevention : Not applicable. Response : Not applicable. Storage : Not applicable. Disposal : Not applicable. GHS label elements Percentage of the mixture consisting of ingredient(s) of unknown hazards to the aquatic environment: 6% General : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and available for employees and other users of this product. Hazards not otherwise classified : None known. No signal word. Date of issue/Date of revision : 08/28/2023 Version : 1 1/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 3. Composition/information on ingredients Other means of identification : Not available. Substance/mixture : Mixture Ingredient name CAS number% There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified and hence require reporting in this section. Occupational exposure limits, if available, are listed in Section 8. Any concentration shown as a range is to protect confidentiality or is due to batch variation. Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based ?75 - ?90 72623-87-1 Distillates (petroleum), hydrotreated heavy paraffinic ?10 - ?15 64742-54-7 Distillates (petroleum), solvent-dewaxed heavy paraffinic ?3 64742-65-0 Distillates (petroleum), hydrotreated light paraffinic ?3 64742-55-8 Distillates (petroleum), solvent-dewaxed light paraffinic ?3 64742-56-9 phenol, (tetrapropenyl) deriva-tives <0.025 74499-35-7 Wash out mouth with water. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Do not induce vomiting unless directed to do so by medical personnel. Get medical attention if symptoms occur. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Get medical attention if irritation occurs. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Remove victim to fresh air and keep at rest in a position comfortable for breathing. Get medical attention if symptoms occur. Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion : : : : Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Description of necessary first aid measures Specific treatments : No specific treatment. Most important symptoms/effects, acute and delayed Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact Over-exposure signs/symptoms Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Potential acute health effects Indication of immediate medical attention and special treatment needed, if necessary Date of issue/Date of revision : 08/28/2023 Version : 1 2/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 4. First aid measures See toxicological information (Section 11) Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide In a fire or if heated, a pressure increase will occur and the container may burst. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters Use an extinguishing agent suitable for the surrounding fire. Extinguishing media : : : Do not use water jet. Suitable extinguishing media : Unsuitable extinguishing media : Special protective actions for fire-fighters : Section 6. Accidental release measures Environmental precautions Personal precautions, protective equipment and emergency procedures Stop leak if without risk. Move containers from spill area. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. : : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Put on appropriate personal protective equipment. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Large spill : Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up For non-emergency personnel For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Section 7. Handling and storage Advice on general occupational hygiene Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. : Protective measures Put on appropriate personal protective equipment (see Section 8).: Precautions for safe handling Date of issue/Date of revision : 08/28/2023 Version : 1 3/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 7. Handling and storage Conditions for safe storage, including any incompatibilities Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : Section 8. Exposure controls/personal protection Control parameters Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), hydrotreated heavy paraffinic ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed heavy paraffinic ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), hydrotreated light paraffinic ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed light paraffinic ACGIH TLV (United States, 1/2022). [Mineral Oil, pure, highly and severely refined] TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). [Oil Ingredient name Exposure limits Occupational exposure limits Date of issue/Date of revision : 08/28/2023 Version : 1 4/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 8. Exposure controls/personal protection Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side- shields. Eye/face protection Respiratory protection : : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. : Environmental exposure controls : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate engineering controls : Good general ventilation should be sufficient to control worker exposure to airborne contaminants. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. mist, mineral] TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2020). [OIL MIST MINERAL] TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist phenol, (tetrapropenyl) deriva-tives None. Biological exposure indices No exposure indices known. Section 9. Physical and chemical properties and safety characteristics Physical state Melting point/freezing point Liquid. Not available. Not available.Odor pH Amber.Color Not available. Not available.Odor threshold : : : : : : Appearance Boiling point, initial boiling point, and boiling range : Not available. The conditions of measurement of all properties are at standard temperature and pressure unless otherwise indicated. Date of issue/Date of revision : 08/28/2023 Version : 1 5/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 9. Physical and chemical properties and safety characteristics Vapor pressure Relative density Relative vapor density 0.843 Not available. Evaporation rate Not available. Auto-ignition temperature Flash point Closed cup: 205?C (401?F) Not applicable. Viscosity Kinematic (40?C (104?F)): 38.1 mm2/s (38.1 cSt) Partition coefficient: n- octanol/water : : : : : : : : Flammability : Not available. Lower and upper explosion limit/flammability limit : Not available. Decomposition temperature : Not available. Solubility in water : Not available. Flow time (ISO 2431) : Not available. Particle characteristics Median particle size : Not applicable. Ingredient name ?C ?F Method Soybean oil 444.85 832.7 Ingredient name Vapor Pressure at 20?C Vapor pressure at 50?C mm Hg kPa Method mm Hg kPa Method Lubricating oils (petroleum), C20-50, hydrotreated neutral oil- based <0.08 <0.011 ASTM D 5191 Pour point : -45?C (-49?F) Solubility(ies) : Not available. Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid No specific data. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable.Chemical stability No specific data. : : : Incompatible materials : Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity : No specific test data related to reactivity available for this product or its ingredients. Section 11. Toxicological information Acute toxicity Information on toxicological effects Date of issue/Date of revision : 08/28/2023 Version : 1 6/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 11. Toxicological information Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based LC50 Inhalation Dusts and mists Rat 2.18 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), hydrotreated heavy paraffinic LC50 Inhalation Dusts and mists Rat 5.7 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed heavy paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), hydrotreated light paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed light paraffinic LD50 Dermal Rabbit >5000 mg/kg - LD50 Dermal Rat >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Product/ingredient name Result Species Dose Exposure Carcinogenicity Not available. Mutagenicity Not available. Teratogenicity Not available. Reproductive toxicity Not available. Irritation/Corrosion Not available. Sensitization Not available. Information on the likely routes of exposure Inhalation : No known significant effects or critical hazards. Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Not available. Not available. Aspiration hazard Name Result Distillates (petroleum), hydrotreated light paraffinic ASPIRATION HAZARD - Category 1 Distillates (petroleum), solvent-dewaxed light paraffinic ASPIRATION HAZARD - Category 1 : Not available. Potential acute health effects Date of issue/Date of revision : 08/28/2023 Version : 1 7/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 11. Toxicological information Not available. No known significant effects or critical hazards.:Ingestion No known significant effects or critical hazards.General : No known significant effects or critical hazards.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Potential chronic health effects Delayed and immediate effects and also chronic effects from short and long term exposure Potential immediate effects : Not available. Short term exposure Potential delayed effects : Not available. Potential immediate effects : Not available. Long term exposure Potential delayed effects : Not available. Numerical measures of toxicity Acute toxicity estimates Product/ingredient name Bel-Ray Full Synthetic 0W-16 N/A 2634.2 N/A N/A N/A Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated heavy paraffinic N/A 2500 N/A N/A 5.7 Distillates (petroleum), solvent-dewaxed heavy paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated light paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), solvent-dewaxed light paraffinic N/A 2500 N/A N/A N/A Oral (mg/ kg) Dermal (mg/kg) Inhalation (gases) (ppm) Inhalation (vapors) (mg/l) Inhalation (dusts and mists) (mg/ l) No known significant effects or critical hazards.Reproductive toxicity : Section 12. Ecological information Toxicity Date of issue/Date of revision : 08/28/2023 Version : 1 8/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects : No known significant effects or critical hazards. Product/ingredient name Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based >6 - High Distillates (petroleum), hydrotreated heavy paraffinic >6 - High Distillates (petroleum), solvent-dewaxed heavy paraffinic 2 to 6 - High Distillates (petroleum), hydrotreated light paraffinic >6 - High Product/ingredient name Aquatic half-life Photolysis Biodegradability Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based - - Inherent Distillates (petroleum), hydrotreated heavy paraffinic - - Not readily Distillates (petroleum), hydrotreated light paraffinic - - Inherent Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Crustaceans 48 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), hydrotreated heavy paraffinic Acute EC50 >100 mg/l Daphnia 48 hours Acute IC50 >100 mg/l Algae 72 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), solvent-dewaxed heavy paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Chronic NOEL >1 mg/l Daphnia 21 days Distillates (petroleum), hydrotreated light paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), solvent-dewaxed light paraffinic Acute LC50 4.5 mg/l Fish 96 hours Product/ingredient name SpeciesResult Exposure Persistence and degradability Soil/water partition coefficient (KOC) : Not available. Mobility in soil Date of issue/Date of revision : 08/28/2023 Version : 1 9/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. :Disposal methods Section 14. Transport information Not regulated.Not regulated. Not regulated. DOT Classification IMDG IATA UN number TDG Classification Not regulated. Special precautions for user Transport in bulk according to IMO instruments Transport within user?s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : Not available. : Section 15. Regulatory information U.S. Federal regulations Clean Water Act (CWA) 307: zinc O,O,O',O'-tetrakis(1,3-dimethylbutyl) bis (phosphorodithioate); Phosphorodithioic acid, O,O-di-C1-14-alkyl esters, zinc salts : Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) : Not listed Clean Air Act Section 602 Class I Substances : Not listed Clean Air Act Section 602 Class II Substances : Not listed DEA List I Chemicals (Precursor Chemicals) : Not listed DEA List II Chemicals (Essential Chemicals) : Not listed TSCA 8(a) PAIR: Phosphorodithioic acid, O,O-di-C1-14-alkyl esters, zinc salts; diphenylamine; phenol, (tetrapropenyl) deriva-tives TSCA 8(a) CDR Exempt/Partial exemption: Not determined SARA 302/304 SARA 304 RQ : Not applicable. No products were found. Composition/information on ingredients SARA 311/312 Classification : Not applicable. Composition/information on ingredients Date of issue/Date of revision : 08/28/2023 Version : 1 10/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 15. Regulatory information Viet Nam The following components are listed: OIL MIST, MINERALMassachusetts : California Prop. 65 New York : None of the components are listed. New Jersey : None of the components are listed. Pennsylvania : None of the components are listed. State regulations International lists National inventory Australia : All components are listed or exempted. Canada : At least one component is not listed in DSL but all such components are listed in NDSL. China : Not determined. Republic of Korea : All components are listed or exempted. New Zealand : All components are listed or exempted. Philippines : Not determined. Taiwan : All components are listed or exempted. Turkey : Not determined. United States : All components are active or exempted. Thailand : Not determined. Distillates (petroleum), hydrotreated light paraffinic ?3 ASPIRATION HAZARD - Category 1 Distillates (petroleum), solvent- dewaxed light paraffinic ?3 ASPIRATION HAZARD - Category 1 Name % Classification : Not determined. This product is not known to contain California Prop 65 substances ?1 ppm Eurasian Economic Union : Russian Federation inventory: Not determined. Section 16. Other information History Date of issue/Date of revision Version Notice to reader Date of previous issue : : : Indicates information that has changed from previously issued version. Key to abbreviations : 08/28/2023 No previous validation 1 Procedure used to derive the classification Classification Justification Not classified. ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations Date of issue/Date of revision : 08/28/2023 Version : 1 11/12Date of previous issue : No previous validation FVP Full Synthetic 0W-16 Section 16. Other information To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Date of issue/Date of revision : 08/28/2023 Version : 1 12/12Date of previous issue : No previous validation