3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 1 of 10 Safety Data Sheet Copyright,2022, 3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 24-0677-5 Version Number: 3.11 Issue Date: 08/05/22 Supercedes Date: 08/12/16 SECTION 1: Identification 1.1. Product identifier 3M? Abrasive Products, 777F includes Roloc?, Stikit? 1.2. Recommended use and restrictions on use Recommended use Abrasive Product 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Abrasive Systems Division ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification 2.1. Hazard classification Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200. 2.2. Label elements Signal word Not applicable. Symbols Not applicable. Pictograms Not applicable. 27% of the mixture consists of ingredients of unknown acute oral toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Ceramic Aluminum Oxide / Aluminum Oxide Mineral 1344-28-1 10 - 40 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 2 of 10 Blend (non-fibrous) Cured Resin Mixture 5 - 40 Cloth Backing None 5 - 40 PSA Mixture 0 - 20 Filler 1317-65-3 1 - 15 Filler 13983-17-0 0 - 15 Inorganic Fluoride 14075-53-7 2 - 15 Inorganic Fluoride 15096-52-3 2 - 10 Attachment Button Mixture 0 - 10 Pigment 1332-37-2 0.10 - 1.5 Titanium Dioxide 13463-67-7 0.05 - 1.5 SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Wash with soap and water. If signs/symptoms develop, get medical attention. Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: No need for first aid is anticipated. 4.2. Most important symptoms and effects, both acute and delayed No critical symptoms or effects. See Section 11.1, information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion 5.3. Special protective actions for fire-fighters No special protective actions for fire-fighters are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Observe precautions from other sections. 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 3 of 10 6.2. Environmental precautions Avoid release to the environment. 6.3. Methods and material for containment and cleaning up Not applicable. SECTION 7: Handling and storage 7.1. Precautions for safe handling For industrial/occupational use only. Not for consumer sale or use. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Avoid release to the environment. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions. 7.2. Conditions for safe storage including any incompatibilities No special storage requirements. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component. Ingredient C.A.S. No. Agency Limit type Additional Comments Filler 1317-65-3 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 Aluminum, insoluble compounds 1344-28-1 ACGIH TWA(respirable fraction):1 mg/m3 A4: Not class. as human carcin Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) 1344-28-1 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 Titanium Dioxide 13463-67-7 ACGIH TWA:10 mg/m3 A4: Not class. as human carcin Titanium Dioxide 13463-67-7 OSHA TWA(as total dust):15 mg/m3 Filler 13983-17-0 ACGIH TWA(inhalable fraction):1 mg/m3 A4: Not class. as human carcin Aluminum, insoluble compounds 15096-52-3 ACGIH TWA(respirable fraction):1 mg/m3 A4: Not class. as human carcin FLUORIDES 15096-52-3 ACGIH TWA(as F):2.5 mg/m3 A4: Not class. as human carcin FLUORIDES 15096-52-3 OSHA TWA(as F):2.5 mg/m3;TWA(as dust):2.5 mg/m3 ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 4 of 10 CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Provide appropriate local exhaust ventilation for sanding, grinding or machining. Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Provide local exhaust at process emission sources to control exposure near the source and to prevent the escape of dust into the work area. Ensure that dust-handling systems (such as exhaust ducts, dust collectors, vessels, and processing equipment) are designed in a manner to prevent the escape of dust into the work area (i.e., there is no leakage from the equipment). 8.2.2. Personal protective equipment (PPE) Eye/face protection To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding operations or when near such operations. Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Skin/hand protection Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from grinding or sanding. Respiratory protection Assess exposure concentrations of all materials involved in the work process. Consider material being abraded when determining the appropriate respiratory protection. Select and use appropriate respirators to prevent inhalation overexposure. An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties Appearance Physical state Color Solid Red Odor Slight Polymeric Odor threshold Not Applicable pH Not Applicable Melting point Not Applicable Boiling Point Not Applicable Flash Point Not Applicable Evaporation rate Not Applicable Flammability (solid, gas) Not Classified Flammable Limits(LEL) Not Applicable Flammable Limits(UEL) Not Applicable Vapor Pressure Not Applicable 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 5 of 10 Vapor Density Not Applicable Density Not Applicable Specific Gravity Not Applicable Solubility In Water Not Applicable Solubility- non-water Not Applicable Partition coefficient: n-octanol/ water Not Applicable Autoignition temperature Not Applicable Decomposition temperature Not Applicable Viscosity Not Applicable SECTION 10: Stability and reactivity 10.1. Reactivity This material is considered to be non reactive under normal use conditions. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid None known. 10.5. Incompatible materials None known. 10.6. Hazardous decomposition products Substance Condition None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Dust from grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching. 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 6 of 10 Eye Contact: Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion. Dust created by grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Ingestion: No known health effects. Carcinogenicity: Ingredient CAS No. Class Description Regulation TITANIUM DIOXIDE 13463-67-7 Grp. 2B: Possible human carc. International Agency for Research on Cancer Additional Information: This product, when used under reasonable conditions and in accordance with the directions for use, should not present a health hazard. However, use or processing of the product in a manner not in accordance with the product's directions for use may affect the performance of the product and may present potential health and safety hazards. This document covers only the 3M product. For complete assessment, when determining the degree of hazard, the material being abraded must also be considered. This product contains titanium dioxide. Cancer of the lungs has been observed in rats that inhaled high levels of titanium dioxide. No exposure to inhaled titanium dioxide is expected during the normal handling and use of this product. Titanium dioxide was not detected when air sampling was conducted during simulated use of similar products containing titanium dioxide. Therefore, the health effects associated with titanium dioxide are not expected during the normal use of this product. Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Ingestion No data available; calculated ATE >5,000 mg/kg Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Dermal LD50 estimated to be > 5,000 mg/kg Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Inhalation- Dust/Mist (4 hours) Rat LC50 > 2.3 mg/l Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Ingestion Rat LD50 > 5,000 mg/kg Inorganic Fluoride Dermal LD50 estimated to be > 5,000 mg/kg Inorganic Fluoride Inhalation- Dust/Mist (4 hours) Rat LC50 > 5.3 mg/l Inorganic Fluoride Ingestion Rat LD50 5,854 mg/kg Filler Dermal LD50 estimated to be > 5,000 mg/kg Filler Ingestion LD50 estimated to be 2,000 - 5,000 mg/kg Filler Dermal Rat LD50 > 2,000 mg/kg Filler Inhalation- Dust/Mist (4 hours) Rat LC50 3 mg/l Filler Ingestion Rat LD50 6,450 mg/kg Inorganic Fluoride Dermal Rabbit LD50 > 2,100 mg/kg Inorganic Fluoride Inhalation- Dust/Mist (4 hours) Rat LC50 4.5 mg/l Inorganic Fluoride Ingestion Rat LD50 5,000 mg/kg Titanium Dioxide Dermal Rabbit LD50 > 10,000 mg/kg Titanium Dioxide Inhalation- Dust/Mist (4 hours) Rat LC50 > 6.82 mg/l 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 7 of 10 Titanium Dioxide Ingestion Rat LD50 > 10,000 mg/kg Pigment Dermal Not available LD50 3,100 mg/kg Pigment Ingestion Not available LD50 3,700 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Rabbit No significant irritation Inorganic Fluoride Rabbit No significant irritation Filler Rabbit No significant irritation Inorganic Fluoride Multiple animal species No significant irritation Titanium Dioxide Rabbit No significant irritation Pigment Rabbit No significant irritation Serious Eye Damage/Irritation Name Species Value Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Rabbit No significant irritation Inorganic Fluoride Rabbit No significant irritation Filler Rabbit No significant irritation Inorganic Fluoride Rabbit Mild irritant Titanium Dioxide Rabbit No significant irritation Pigment Rabbit No significant irritation Skin Sensitization Name Species Value Titanium Dioxide Human and animal Not classified Pigment Human Not classified Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) In Vitro Not mutagenic Filler In Vitro Not mutagenic Titanium Dioxide In Vitro Not mutagenic Titanium Dioxide In vivo Not mutagenic Pigment In Vitro Not mutagenic Carcinogenicity Name Route Species Value Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non- fibrous) Inhalation Rat Not carcinogenic Titanium Dioxide Ingestion Multiple animal species Not carcinogenic Titanium Dioxide Inhalation Rat Carcinogenic Pigment Inhalation Human Some positive data exist, but the data are not sufficient for classification Reproductive Toxicity 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 8 of 10 Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration Filler Ingestion Not classified for development Rat NOAEL 625 mg/kg/day premating & during gestation Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Filler Inhalation respiratory system Not classified Rat NOAEL 0.812 mg/l 90 minutes Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Inhalation pneumoconiosis Some positive data exist, but the data are not sufficient for classification Human NOAEL Not available occupational exposure Ceramic Aluminum Oxide / Aluminum Oxide Mineral Blend (non-fibrous) Inhalation pulmonary fibrosis Not classified Human NOAEL Not available occupational exposure Filler Inhalation respiratory system Not classified Human NOAEL Not available occupational exposure Filler Inhalation pulmonary fibrosis Not classified Human and animal NOAEL Not available Filler Inhalation respiratory system Not classified Human NOAEL Not available occupational exposure Inorganic Fluoride Inhalation bone, teeth, nails, and/or hair Causes damage to organs through prolonged or repeated exposure Rat NOAEL 0.0005 mg/l 5 months Inorganic Fluoride Inhalation respiratory system Causes damage to organs through prolonged or repeated exposure Rat NOAEL 0.00021 mg/l 90 days Inorganic Fluoride Ingestion bone, teeth, nails, and/or hair Causes damage to organs through prolonged or repeated exposure Rat LOAEL 0.58 mg/kg/day 14 weeks Titanium Dioxide Inhalation respiratory system Some positive data exist, but the data are not sufficient for classification Rat LOAEL 0.01 mg/l 2 years Titanium Dioxide Inhalation pulmonary fibrosis Not classified Human NOAEL Not available occupational exposure Pigment Inhalation pulmonary fibrosis | pneumoconiosis Not classified Human NOAEL Not available occupational exposure Aspiration Hazard For the component/components, either no data are currently available or the data are not sufficient for classification. Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 9 of 10 SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. The substrate that was abraded must be considered as a factor in the disposal method for this product. Incinerate in a permitted waste incineration facility. EPA Hazardous Waste Number (RCRA): Not regulated SECTION 14: Transport Information Not regulated per U.S. DOT, IATA or IMO. These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for complying with all applicable laws and regulations, including proper transportation classification and packaging. 3M transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of applicable current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to transportation classification and not the packaging, labeling, or marking requirements. The original 3M package is certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory requirements. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information. EPCRA 311/312 Hazard Classifications: Physical Hazards Not applicable Health Hazards Not applicable 15.2. State Regulations Contact 3M for more information. 15.3. Chemical Inventories This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 0 Flammability: 1 Instability: 0 Special Hazards: None 3M? Abrasive Products, 777F includes Roloc?, Stikit? 08/05/22 __________________________________________________________________________________________ Page 10 of 10 National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. HMIS Hazard Classification Health: 0 Flammability: 1 Physical Hazard: 0 Personal Protection: X - See PPE section. Hazardous Material Identification System (HMIS? IV) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS? IV ratings are to be used with a fully implemented HMIS? IV program. HMIS? is a registered mark of the American Coatings Association (ACA). Document Group: 24-0677-5 Version Number: 3.11 Issue Date: 08/05/22 Supercedes Date: 08/12/16 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M. 3M USA SDSs are available at www.3M.com