Revision date: Feb. 19. 2024 1 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 SAFETY DATA SHEET According to US OSHA Hazard Communication Standard (29 CFR 1910.1200) Revision date: Feb. 19. 2024 Product Name SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 Recommended use and restriction on use Use of the Substance/Mixture : Gear oil Uses advised against : Use only for Lubricants Supplier?s details Supplier Name : SK Enmove Americas Inc. Address : 11700 Katy Freeway Suite 1200, Houston, TX 77079, USA Information Contac: : +1-859-625-8201 E mail : This email address is being protected from spambots. You need JavaScript enabled to view it. Emergency telephone numbers +1-859-625-8201 Classification of the chemical in accordance with paragraph (d) of ?1910.1200 - Serious Eye Damage/Eye Irritation : Category 2A Label elements Hazard symbols Signal words Warning Hazard statements H319 Causes serious eye irritation Precautionary statements 1) Prevention P264 Wash hands thoroughly after handling. P280 Wear protective gloves/protective clothing/eye protection/face protection. 2) Response P337+P313 If eye irritation persists: Get medical advice/attention. P305+P351+P338 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. 3) Storage Not applicable 4) Disposal Not applicable dHazards not otherwise classified (HNOC): Environmental hazards Expected to be toxic to aquatic organisms. May cause long-term adverse effects in the aquatic environment. Description of the mixture: - Hydrocarbon lubricating base oil with functional additives Hazardous ingredients: Substance Name CAS No. Concentration (wt%) Distillates (petroleum), hydrotreated light paraffinic 64742-55-8 >=40, < 50 Distillates (petroleum), hydrotreated heavy paraffinic 64742-54-7 >=20, < 30 SECTION 3: COMPOSITION/INFORMATION ON INGREDIENTS SECTION 1: IDENTIFICATION SECTION 2: HAZARDS IDENTIFICATION 19300457,19300458,19367024,19420402, 19421099, 88866023 ACDelco Rear Axle Lubricant High Efficiency SAE 75W-85 MZ7G2L Stamp Revision date: Feb. 19. 2024 2 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 Di-tert-butyl polysulfides 68937-96-2 >=1, < 5 Mineral oil - >=1, < 5 The mineral oil contained in this material may be described by one or more of the following CAS Nos.: 64742-54-7, 64742-65-0, 64742-55-8, and 64742-56-9. Other ingredients are either not hazardous or are below the regulatory disclosure limit. As per paragraph (i) of 29 CFR 1910.1200, formulation is considered a trade secret and specific chemical identity and exact percentage (concentration) of composition may have been withheld. Specific chemical identity and exact percentage composition will be provided to health professionals, employees, or designated representatives in accordance with applicable provisions of paragraph (i). Description of first aid measures First-aid measures general - No general information. First-aid measures after inhalation - When exposed to large amounts of steam and mist, move to fresh air. - Take specific treatment if needed. Skin Contact - Flush skin with plenty of water for at least 15 minutes while removing contaminated clothing and shoes. - Wash contaminated clothing thoroughly before re-using. Eye Contact - Do not rub your eyes. - Immediately flush eyes with plenty of water for at least 15 minutes and call a doctor/physician. Ingestion - Please be advised by doctor whether induction of vomit is demanded or not. - Rinse your mouth with water immediately. Most important symptoms and effects, both acute and delayed Not available Indication of any immediate medical attention and special treatment needed Notify medical personnel of contaminated situations and have them take appropriate protective measures. Extinguishing media Suitable extinguishing media - Dry chemical, carbon dioxide, regular foam extinguishing agent, spray Unsuitable extinguishing media - Avoid use of water jet for extinguishing Special hazards arising from the substrate or mixture Hazardous combustion products - Not available Advice for fire-fighters - Move containers from fire area if you can do without the risk. - Keep unauthorized personnel out. - Withdraw immediately in case of rising sound from venting safety devices or discoloration of tank. - Notify your local fire station and inform the location of the fire and characteristics hazard. - Keep containers cool with water spray. - Use firefighting procedures suitable for surrounding area. - Vapor or gas is burned at distant ignition sources can be spread quickly. SECTION 4: FIRST AID MEASURES SECTION 5: FIRE FIGHTING MEASURES SECTION 6: ACCIDENTAL RELEASE MEASURES Revision date: Feb. 19. 2024 3 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 Personal precautions, protective equipment, and emergency procedures For non-emergency personnel - Protective equipment: Wear proper protective equipment. - Emergency procedures: Not applicable - If required, notify relevant authorities according to all applicable regulations. For emergency responders- Ventilate closed spaces before entering. - Must work against the wind, let the upwind people to evacuate. - Do not touch spilled material. Stop leak if you can do it without risk. - Handle the damaged containers or spilled material after wearing appropriate protective equipment - Do not direct water at spill or source of leak. Environmental precautions - Prevent runoff and contact with waterways, drains or sewers. - If large amounts have been spilled, inform the relevant authorities. - Avoid dispersal of spilt material and runoff and contact with waterways, drains and sewers. If large spills, advise emergency services. Methods and material for containment and cleaning up For containment - Clear spills immediately - Clean up all spills immediately. - Prevent, by any means available, spillage from entering drains or water course. - No smoking, flame, or ignition sources. For cleaning up - Large spill : Stay upwind and keep out of low areas. Dike for later disposal. - Notification to central government, local government. When emissions at least of the standard amount - Dispose of waste in accordance with local regulation. - Appropriate container for disposal of spilled material collected. - Small leak: sand or other non-combustible material, please let use absorption. - Wipe off the solvent. - Dike for later disposal. - Prevent the influx to waterways, sewers, basements, or confined spaces. Other information - Slippery when spilt. Reference to other sections - See Section 7 for information on safe handling. - See Section 8 for information on personal protection equipment. - See Section 13 for information on disposal. Precautions for safe handling - Avoid direct physical contact. - Since emptied containers retain product residue (vapor, liquid, solid) follow all MSDS and label warnings even after container is emptied. - Refer to Engineering controls and personal protective equipment. - Do not handle until all safety precautions have been read and understood. - Do not inhale the steam prolonged or repeated. Conditions for safe storage, including any incompatibilities - Check regularly for leaks. - Do not apply any physical shock to container. - Keep sealed when not in use. - No open fire. - Prevent static electricity and keep away from combustible materials or heat sources. - Store away from water and sewer. - Collected them in sealed containers. SECTION 8: EXPOSURE CONTROL/PERSONAL PROTECTION SECTION 7: HANDLING AND STORAGE Revision date: Feb. 19. 2024 4 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 Control parameters Occupational exposure limit values When mists/aerosols can occur, the following are recommended: 5mg/m? - ACGIH TLV, 10 mg/m? - ACGIH STEL Biological limit values No biological limit allocated. Exposure limit at intended use - Personal, workplace atmosphere or biological monitoring may be required to determine the effectiveness of the ventilation or other control measures and/or the necessity to use respiratory protective equipment. Exposure controls Appropriate engineering controls - Business owner is recommended to maintain below recommended exposure limits for the working place with general exhaust of gas/vapour/mist/fume. personal protective equipment Hand protection - Wear appropriate glove. Eye protection - Wear primary eye protection such as splash resistant safety goggles with a secondary protection face shield. - Provide an emergency eye wash station and quick drench shower in the immediate work area. Skin protection - Wear appropriate clothing. Respiratory Protection - Respiratory protection is ranked in order from minimum to maximum. - Consider warning properties before use. Thermal hazards - Not available Others - It is necessary to wear protective clothes and other protection equipment. Cover your face, head, and neck. - Prior to removing protective garments, the employee should undergo decontamination and be required to shower upon removal of the garments and hood. - Emergency deluge showers and eyewash fountains, supplied with potable water, should be located near, within sight of, and on the same level with locations where direct exposure is likely. Environmental exposure controls - Do not let product enter drains. For ecological information refer to section 12. Information on basic physical and chemical properties Appearance (State) Liquid Appearance (Color) Amber Odor Mild petroleum odor Odor threshold Not available pH Not available Melting point / freezing point Not available Initial boiling point and boiling range Not available Flash point 200 ?C (392?F) (COC) Evaporating Rate Not available Flammability (solid, gas) Not available Upper/Lower Flammability or explosive limits Not available Vapor pressure Not available Vapor density Not available Relative density 0.85 - 0.89 (15.6 ? C (60.1 ? F)) Solubility Not available Partition coefficient of n-octanol/water Not available Autoignition Temperature 572 ?F (300 ?C) SECTION 9: PHYSICAL AND CHEMICAL PROPERTIES Revision date: Feb. 19. 2024 5 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 Decomposition Temperature Not available Viscosity 74 ? / s (40 ? C (104 ? F)) Explosives properties Not available Oxidising properties Not available Other information - DMSO extract by IP346 : Less than 3.0 wt% (mineral oil component only) Reactivity - Not available Chemical stability - This material is stable under recommended storage and handling conditions. Possibility of Hazardous Reaction - Hazardous Polymerization will not occur. Conditions to avoid - Avoid contact with incompatible materials and condition. - Avoid : Accumulation of electrostatic charges, Heating, Flames and hot surfaces Incompatible materials - Strong acids. Strong oxidizing agents. Hazardous decomposition products - May emit flammable vapor if involved in fire. Smoke, carbon monoxide, carbon dioxide, aldehydes and other products of incomplete combustion. Hydrogen sulfide and alkyl mercaptans and sulfides may also be released. Thermal decomposition or combustion may generate smoke, carbon monoxide, carbon dioxide, and other products of incomplete combustion. Information on the likely routes of exposure (Respiratory tracts) - Not available (Oral) - Not available (Eye Skin) - Not available Delayed and immediate effects and also chronic effects from short and long term exposure Acute toxicity Oral - Product (ATEmix) : >5000mg/kg - [Distillates (petroleum), hydrotreated light paraffinic] : LD50 > 5000 ?/? Rat (GLP, ECHA) - [Distillates (petroleum), hydrotreated heavy paraffinic] : LD50 > 5000 mg/kg Rat (ECHA) - [Di-tert-butyl polysulfides] : LD50 6500 ?/? Rat (IUCLID) Dermal - Product (ATEmix) : 2000mg/kg < ATEmix <= 5000mg/kg - [Distillates (petroleum), hydrotreated light paraffinic] : LD50 > 5000 ?/? Rabbit (GLP, ECHA) - [Distillates (petroleum), hydrotreated heavy paraffinic] : LD50 >5000 mg/kg Rabbit (ECHA) Inhalation - Product (ATEmix) : 2.0mg/L < ATEmix <= 10.0mg/L - [Distillates (petroleum), hydrotreated light paraffinic] : LC50 >5.53 ?/? 4 hr Rat (ECHA) - [Distillates (petroleum), hydrotreated heavy paraffinic] : Aerosol LC50 > 5.53 mg/L 4 hr, Rat, Read-across : CAS No. 64741-88-4 (ECHA) Skin corrosion/irritation - Not available Serious eye damage/irritation SECTION 10: STABILITY AND REACTIVITY SECTION 11: TOXICOLOGICAL INFORMATION Revision date: Feb. 19. 2024 6 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 - Causes serious eye irritation Respiratory sensitization - Not available Skin sensitization - [Di-tert-butyl polysulfides] May cause sensitization by skin contact. Remarks: Category 1B Carcinogenicity IARC - Not available OSHA - Not available ACGIH - Not available NTP - Not available EU CLP - [Distillates (petroleum), hydrotreated light paraffinic] : Carc. 1B (Note L) - [Distillates (petroleum), hydrotreated heavy paraffinic] : Carc. 1B (Note L) It is not considered carcinogenic. it has been demonstrated to contain less than 3% extractables by the IP 346 test (EU CLP Note L) Germ cell mutagenicity - Not available Reproductive toxicity - Not available STOT-single exposure - Not available STOT-repeated exposure - Not available Aspiration hazard - Not available Ecotoxicity Fish - [Distillates (petroleum), hydrotreated light paraffinic] : LC50 5000 ?/? 96 hr Oncorhynchus mykiss (IUCLID) - [Distillates (petroleum), hydrotreated heavy paraffinic] : LL50 > 100 mg/L, 96hr, Pimephales promelas (ECHA) - [Di-tert-butyl polysulfides] : LC50 250 ~ 800 ?/? 96 hr Pimephales promelas (GLP, OECD TG 203) (IUCLID) Crustaceans - [Distillates (petroleum), hydrotreated light paraffinic] : EC50 1000 ?/? 48 hr Daphnia magna (IUCLID) - [Distillates (petroleum), hydrotreated heavy paraffinic] : EL50 > 10000 mg/L, 48hr, Daphnia magna (ECHA) - [Di-tert-butyl polysulfides] : EC50 1000 ?/? 48 hr Daphnia magna (GLP, OECD TG 202) (IUCLID) Algae - [Distillates (petroleum), hydrotreated heavy paraffinic] : EC25 1152.9 mg/L, 96hr, Pseudokirchneriella subcapitata, NOEL >= 100 mg/L, 72hr (ECHA) - [Di-tert-butyl polysulfides] : EbC50 20 ~ 39 ?/? 96 hr Selenastrum capricornutum (GLP, OECD TG 201) (IUCLID- Persistence and degradability Persistence - [Distillates (petroleum), hydrotreated heavy paraffinic] : log Pow = 1.99 ~ 18.02 (20?C) (ECHA) - [Di-tert-butyl polysulfides] : log Kow 6 (IUCLID, SIDS) Degradability - Not available Bioaccumulative potential Bioaccumulative potential - [Di-tert-butyl polysulfides] : BCF 4500 ~ 42600 (Has the potential bioaccumulation) (SIDS) Biodegration SECTION 12: ECOLOGICAL INFORMATION Revision date: Feb. 19. 2024 7 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 - [Di-tert-butyl polysulfides] : 82 (%) 28 day (OECD TG 301G, Degradation in vivo accumulation potential to be so well Low) (SIDS) Mobility in soil - Not available Other adverse effects - Not available Waste treatment methods Disposal recommendations based on material as supplied, Disposal must be in accordance with applicable laws and regulations, and material characteristics at time of disposal For the safety of persons conducting disposal, recycling or reclamation activities, refer to the information in Section 8, Exposure control and personal protection. Disposal recommendations Product The product should not be allowed to enter drains, water courses or the soil. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose of contents/ container to an approved waste disposal plant. Empty Container Empty Container Warning (where applicable): Empty containers may contain residue and can be dangerous. Do not attempt to refill or clean containers without proper instructions. Empty drums should be completely drained and safely stored until appropriately reconditioned or disposed. Empty containers should be taken for recycling, recovery, or disposal through suitably qualified or licensed contractor and in accordance with governmental regulations. DO NOT PRESSURISE, CUT, WELD, BRAZE, SOLDER, DRILL, GRIND, OR EXPOSE SUCH CONTAINERS TO HEAT, FLAME, SPARKS, STATIC ELECTRICITY, OR OTHER SOURCES OF IGNITION. THEY MAY EXPLODE AND CAUSE INJURY OR DEATH. LAND (US DOT) : Not regulated for land transport SEA (IMDG) UN number or ID number: UN 3082 UN Proper Shipping Name: Environmentally hazardous substance, liquid, n.o.s.(Alkenyl amine) Transport Hazard Class(es) Class: 9 Label(s): 9 Packing Group: III Environmental Hazards: Marine Pollutant Special precautions for user: None established AIR (IATA) UN number or ID number: UN 3082 UN Proper Shipping Name: Environmentally hazardous substance, liquid, n.o.s.(Alkenyl amine) Transport Hazard Class(es) Class: 9 Label(s): 9MI Packing Group: III Environmental Hazards: Marine Pollutant Special precautions for user: None established Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code : Not applicable SECTION 14: TRANSPORTATION INFORMATION SECTION 13: DISPOSAL CONSIDERATIONS SECTION 15: REGULATORY INFORMATION Revision date: Feb. 19. 2024 8 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 U.S. Federal/State regulations TSCA 12(b) - Notification of Export of Chemicals None of the components are listed. OSHA HAZARD COMMUNICATION STANDARD This material causes serious eye irritation in accordance with OSHA HazCom 2012, 29 CFR 1910.1200. EPCRA -Emergency Planning and Community Right-to-Know Act Not contain any components with a CERCLA RQ., Shell classifies this mate-rial as an "oil" under the CERCLA Petroleum Exclusion, therefore releases to the environment are not reportable under CERCLA. SARA 302 Extremely Hazardous Substances Threshold Planning Quantity Not contain any components with a section 302 EHS TPQ. SARA 304 Extremely Hazardous Substances Reportable Quantity Not contain any components with a section 304 EHS RQ. SARA 311/312 Hazards Not applicable SARA 313 Not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313. Clean Water Act This product does not contain any Hazardous Chemicals listed under the U.S. CleanWater Act, Section 311, Table 117.3. California Prop. 65 This product can expose you to chemicals including: Methyl isobutyl ketone (361.00PPB) Benzene (180.00PPT) which is [are] known to the State of California to cause cancer and birth defects or other reproductive harm. This product can expose you to chemicals including: Ethyl acrylate (524.00PPB) Naphthalene (2.00PPB) Ethyl benzene (2.00PPB) which is [are] known to the State of California to cause cancer. This product can expose you to chemicals including: Toluene (180.00PPT) which is [are] known to the State of California to cause birth defects or other reproductive harm. Canadian regulations Canada Significant New Activity Notice None of the components are listed. Canadian NPRI None of the components are listed. CEPA Toxic substances None of the components are listed. International Inventory Status DSL : All components are listed or exempted. TSCA : All components are listed or exempted. NFPA Hazard Codes Health Fire Instability 2 1 0 HMIS Health Hazards Flammability Physical Protection 2 1 0 Abbreviations and acronyms DNEL : Derive no effects level PNEC : Predicted no effect concentration ATE : Acute toxicity estimate LC50 : Lethal Concentration to 50 % of a test population LD50 : Lethal Dose to 50% of a test population (Median Lethal Dose) SECTION 16: OTHER INFORMATION Revision date: Feb. 19. 2024 9 / 9 SAE 75W-85 AAM Powerfilm? Gear Oil, P/N 40066893 TWA : Time weighted average Key literature references and sources for data - This Safety Data Sheet was compiled with data and information from the following sources: RTECS, ECOSAR, HSDB, SIDS SIAP, ChemWATCH, CESAR, Chemical DB, ECHA, US Toxic Substances Control Act (TSCA), US California Proposition 65, US Occupational Safety & Health Administration (OSHA) 29 CFR 1910.1200 (Hazard Communication Standard) Further information The (M)SDS is a Hazard Communication tool and should be used to assist in the Risk Assessment. Many factors determine whether the reported Hazards are Risks in the workplace or other settings. Risks may be determined by reference to Exposures Scenarios. Scale of use, frequency of use and current or available engineering controls must be considered. This information is based on our current knowledge and is intended to describe the product for the purposes of health, safety, and environmental requirements only. It should not therefore be construed as guaranteeing any specific property of the product.