Full Text
Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 1 of 7 SDS Version: 1.0 SAFETY DATA SHEET 1. Identification Product Name: TEXIN DEVELOPMENTAL PRODUCT DP7-1097 000000 Material Number: 603489 Chemical Family: Aromatic thermoplastic polyurethane Use: Production of molded plastic articles 2. Hazards Identification GHS Classification This product is not hazardous in the form in which it is shipped by the manufacturer. GHS Label Elements Signal word: Warning Hazard statements: If fine particles are generated during further processing, handling or by other means, product may form combustible dust concentrations in air. 3. Composition/Information on Ingredients Hazardous Components There are no hazardous components above the relevant concentration limits according to OSHA HazCom 2012. 4. First Aid Measures Most Important Symptom(s)/Effect(s) Acute: Contact with heated material can cause thermal burns., Causes a slipping hazard if spilled., Vapors released from thermal decomposition may cause eye irritation with symptoms of burning and tearing, as well as respiratory tract irritation. Bayer MaterialScience LLC Product Safety & Regulatory Affairs 100 Bayer Road Pittsburgh, PA 15205-9741 USA TRANSPORTATION EMERGENCY CALL CHEMTREC: (800) 424-9300 INTERNATIONAL: (703) 527-3887 NON-TRANSPORTATION Emergency Phone: Call Chemtrec Information Phone: (800) 662-2927 jbartel Text Box Bay State Polymer
27540 Detroit Road, Suite 102
Westlake, OH 44145
Phone: 440-892-8500
Fax: 440-892-8436 Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 2 of 7 SDS Version: 1.0 Eye Contact In case of contact, flush eyes with plenty of lukewarm water. Get medical attention if irritation develops. Skin Contact Get medical attention if thermal burn occurs. Inhalation If inhaled, remove to fresh air. Ingestion Get medical attention. Notes to Physician In the event of possible diisocyanate exposure: Eyes: Stain for evidence of corneal injury. If cornea is burned, instill antibiotic/steroid preparation as needed. Workplace vapors could produce reversible corneal epithelial edema impairing vision. Skin: Treat symptomatically as for thermal burn. Ingestion: Treat symptomatically. Inhalation: Treatment is essentially symptomatic. An individual having a pulmonary sensitization reaction to this material should be removed from further exposure to any diisocyanate. 5. Firefighting Measures Suitable Extinguishing Media: Water, Foam, Dry chemical Unsuitable Extinguishing Media: High Pressure Water Streams Fire Fighting Procedure Firefighters should be equipped with self-contained breathing apparatus to protect against potentially toxic and irritating fumes. Hazardous Decomposition Products By Fire and Thermal Decomposition: Carbon Dioxide hydrogen cyanide 4,4'-Diphenylmethane Diisocyanate (MDI) Aldehydes, Carbon monoxide, Amines, Nitriles, Nitrogen oxides (NOx), Hydrocarbons Unusual Fire/Explosion Hazards Toxic and irritating gases/fumes may be given off during burning or thermal decomposition. Avoid generating dust; fine dust dispersed in air in sufficient concentrations, and in the presence of an ignition source is a potential dust explosion hazard. 6. Accidental Release Measures Spill and Leak Procedures If molten, allow material to cool and place into an appropriate marked container for disposal. Sweep up and shovel into suitable containers for disposal. Dust deposits should not be allowed to accumulate on surfaces, as these may form an explosive mixture as they are released into the atmosphere in sufficient concentrations. Avoid dispersal of dust in the air (e.g., cleaning dust from surfaces with compressed air). 7. Handling and Storage Handling/Storage Precautions Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 3 of 7 SDS Version: 1.0 Handle in accordance with good industrial hygiene and safety practices. Wash thoroughly after handling. Avoid breathing dust. Containers should be kept tightly closed to prevent contamination. Material is hygroscopic and may absorb small amounts of atmospheric moisture. Minimize dust generation and accumulation. Routine housekeeping should be instituted to ensure that dust does not accumulate on surfaces. Solid particulate can generate electrical charging during operations such as unloading from containers and pneumatic transfer. Provide adequate precautions, such as electrical grounding and bonding, where conductive equipment is involved. Storage Period: Not Established Storage Temperature Maximum: 30 ?C (86 ?F) Substances to Avoid None known. 8. Exposure Controls/Personal Protection Exposure Limits Thermoplastic Polyurethane (TPU) is generally non-hazardous under ambient conditions., The following exposure limits do not apply to the product in its supplied form; however, when the product is heated (i.e, during processing or thermal decomposition conditions), there is a potential for the release of 4,4'- diphenylmethane diisocyanate (MDI) vapors. 4,4'-Diphenylmethane Diisocyanate (MDI) (101-68-8) US. ACGIH Threshold Limit Values Time Weighted Average (TWA): 0.005 ppm US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Ceiling Limit Value: 0.02 ppm, 0.2 mg/m3 Any component which is listed in section 3 and is not listed in this section does not have a known ACGIH TLV, OSHA PEL or supplier recommended occupational exposure limit. Industrial Hygiene/Ventilation Measures During normal processing, use general dilution and local exhaust as necessary to control airborne vapors, mists, dusts and thermal decomposition products below appropriate airborne concentration standards/guidelines. Special ventilation and personal protective equipment (PPE) is required to control exposure to potentially harmful decomposition products whenever a TPU is heated to temperatures above its decomposition temperature. Examples would include hot knife cutting, grinding, or sawing. Respiratory Protection In the absence of sufficient general dilution or local exhaust ventilation a NIOSH approved air-supplied respirator may be needed during die cleaning, high temperature processing, purging or when thermal decomposition is suspected. Hand Protection Wear heat resistant gloves when handling molten material. Eye Protection Safety glasses with side-shields Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 4 of 7 SDS Version: 1.0 Skin Protection No special skin protection requirements during normal handling and use. Additional Protective Measures Employees should wash their hands and face before eating, drinking, or using tobacco products. Educate and train employees in the safe use and handling of this product. Purgings should be collected as small flat thin shapes or thin strands to allow for rapid cooling. 9. Physical and Chemical Properties State of Matter: solid Appearance: pellets Color: Natural Odor: Odorless Odor Threshold: No Data Available pH: No Data Available Melting Point: 220 ?C (428 ?F) Boiling Point: No Data Available Flash Point: 250 ?C (482 ?F) Evaporation Rate: No Data Available Flammability: No Data Available Lower Explosion Limit: No Data Available Upper Explosion Limit: No Data Available Vapor Pressure: No Data Available Vapor Density: No Data Available Density: 1.1 g/cm? Relative Vapor Density: No Data Available Specific Gravity: 1.1 Solubility in Water: insoluble Partition Coefficient: n- octanol/water: No Data Available Auto-ignition Temperature: > 210 ?C (> 410 ?F) Decomposition Temperature: Decomposition begins at 230 ?C. Softening point: 180 ?C (356 ?F) Dynamic Viscosity: No Data Available Kinematic Viscosity: No Data Available Bulk Density: 500 - 700 kg/m3 Self Ignition: not applicable 10. Stability and Reactivity Hazardous Reactions Hazardous polymerisation does not occur. Stability Stable Materials to Avoid None known. Conditions to Avoid Generation of dust clouds. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 5 of 7 SDS Version: 1.0 Hazardous Decomposition Products By Fire and Thermal Decomposition: Carbon Dioxide ; hydrogen cyanide ; 4,4'-Diphenylmethane Diisocyanate (MDI) ; Aldehydes, Carbon monoxide, Amines, Nitriles, Nitrogen oxides (NOx), Hydrocarbons 11. Toxicological Information Likely Routes of Exposure: Inhalation Skin Contact Eye Contact Health Effects and Symptoms Acute: Contact with heated material can cause thermal burns., Causes a slipping hazard if spilled., Vapors released from thermal decomposition may cause eye irritation with symptoms of burning and tearing, as well as respiratory tract irritation. Toxicity Data for TEXIN DEVELOPMENTAL PRODUCT DP7-1097 000000 In the event of material decomposition due to exceeding the decomposition temperature of this product, release of MDI may occur. Acute Inhalation: The following effects reflect the potential health hazards associated with overexposure to MDI. Diisocyanate vapors or mist at concentrations above the TLV or PEL can irritate (burning sensation) the mucous membranes in the respiratory tract (nose, throat, lungs) causing runny nose, sore throat, coughing, chest discomfort, shortness of breath and reduced lung function (breathing obstruction). Persons with a preexisting, nonspecific bronchial hyperreactivity can respond to concentrations below the TLV or PEL with similar symptoms as well as asthma attack or asthma-like symptoms. Exposure well above the TLV or PEL may lead to bronchitis, bronchial spasm and pulmonary edema (fluid in lungs). Chemical or hypersensitivity pneumonitis, with flu-like symptoms (e.g., fever, chills), has also been reported. These symptoms can be delayed up to several hours after exposure. These effects are usually reversible. Chronic Inhalation: As a result of previous repeated overexposures or a single large dose, certain individuals may develop sensitization to diisocyanates (asthma or asthma-like symptoms) that may cause them to react to a later exposure to diisocyanates at levels well below the TLV or PEL. These symptoms, which can include chest tightness, wheezing, cough, shortness of breath or asthmatic attack, could be immediate or delayed up to several hours after exposure. Extreme asthmatic reactions can be life threatening. Similar to many non- specific asthmatic responses, there are reports that once sensitized an individual can experience these symptoms upon exposure to dust, cold air or other irritants. This increased lung sensitivity can persist for weeks and in severe cases for several years. Sensitization can be permanent. Chronic overexposure to diisocyanates has also been reported to cause lung damage (including fibrosis, decrease in lung function) that may be permanent. Carcinogenicity: No carcinogenic substances as defined by IARC, NTP and/or OSHA 12. Ecological Information No data available for this product. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 6 of 7 SDS Version: 1.0 The components in this product are either non-hazardous or do not have any ecotoxicity data associated with them. 13. Disposal Considerations Waste Disposal Method Waste disposal should be in accordance with existing federal, state and local environmental control laws. 14. Transportation Information Land transport (DOT) Non-Regulated Sea transport (IMDG) Non-Regulated Air transport (ICAO/IATA) Non-Regulated 15. Regulatory Information United States Federal Regulations US. Toxic Substances Control Act: Listed on the TSCA Inventory. US. EPA CERCLA Hazardous Substances (40 CFR 302) Components: None SARA Section 311/312 Hazard Categories: Non-hazardous under Section 311/312 US. EPA Emergency Planning and Community Right-To-Know Act (EPCRA) SARA Title III Section 302 Extremely Hazardous Substance (40 CFR 355, Appendix A) Components: None US. EPA Emergency Planning and Community Right-To-Know Act (EPCRA) SARA Title III Section 313 Toxic Chemicals (40 CFR 372.65) - Supplier Notification Required Components: None US. EPA Resource Conservation and Recovery Act (RCRA) Composite List of Hazardous Wastes and Appendix VIII Hazardous Constituents (40 CFR 261): Under RCRA, it is the responsibility of the person who generates a solid waste, as defined in 40 CFR 261.2, to determine if that waste is a hazardous waste. State Right-To-Know Information The following chemicals are specifically listed by individual states; other product specific health and safety data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropriate agency in your state. Massachusetts, New Jersey or Pennsylvania Right to Know Substance Lists: Weight percent Components CAS-No. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 7 of 7 SDS Version: 1.0 >=1% Polyurethane polyester elastomer 26375-23-5 California Prop. 65: To the best of our knowledge, this product does not contain any of the listed chemicals, which the state of California has found to cause cancer, birth defects or other reproductive harm. Based on information provided by our suppliers, this product is considered ?DRC Conflict Free? as defined by the SEC Conflict Minerals Final Rule (Release No. 34-67716; File No. S7-40-10; Date: 2012-08-22). 16. Other Information The method of hazard communication for Bayer MaterialScience LLC is comprised of Product Labels and Safety Data Sheets. Contact: Product Safety Department Telephone: (412) 777-2835 SDS Number: 112000009385 Version Date: 03/13/2015 SDS Version: 1.0 This information is furnished without warranty, express or implied. This information is believed to be accurate to the best knowledge of Bayer MaterialScience LLC. The information in this SDS relates only to the specific material designated herein. Bayer MaterialScience LLC assumes no legal responsibility for use of or reliance upon the information in this SDS. jbartel Text Box Bay State Polymer
27540 Detroit Road, Suite 102
Westlake, OH 44145
Phone: 440-892-8500
Fax: 440-892-8436 1. Identification 2. Hazards Identification 3. Composition/Information on Ingredients 4. First Aid Measures 5. Firefighting Measures 6. Accidental Release Measures 7. Handling and Storage 8. Exposure Controls/Personal Protection 9. Physical and Chemical Properties 10. Stability and Reactivity 11. Toxicological Information 12. Ecological Information 13. Disposal Considerations 14. Transportation Information 15. Regulatory Information 16. Other Information
27540 Detroit Road, Suite 102
Westlake, OH 44145
Phone: 440-892-8500
Fax: 440-892-8436 Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 2 of 7 SDS Version: 1.0 Eye Contact In case of contact, flush eyes with plenty of lukewarm water. Get medical attention if irritation develops. Skin Contact Get medical attention if thermal burn occurs. Inhalation If inhaled, remove to fresh air. Ingestion Get medical attention. Notes to Physician In the event of possible diisocyanate exposure: Eyes: Stain for evidence of corneal injury. If cornea is burned, instill antibiotic/steroid preparation as needed. Workplace vapors could produce reversible corneal epithelial edema impairing vision. Skin: Treat symptomatically as for thermal burn. Ingestion: Treat symptomatically. Inhalation: Treatment is essentially symptomatic. An individual having a pulmonary sensitization reaction to this material should be removed from further exposure to any diisocyanate. 5. Firefighting Measures Suitable Extinguishing Media: Water, Foam, Dry chemical Unsuitable Extinguishing Media: High Pressure Water Streams Fire Fighting Procedure Firefighters should be equipped with self-contained breathing apparatus to protect against potentially toxic and irritating fumes. Hazardous Decomposition Products By Fire and Thermal Decomposition: Carbon Dioxide hydrogen cyanide 4,4'-Diphenylmethane Diisocyanate (MDI) Aldehydes, Carbon monoxide, Amines, Nitriles, Nitrogen oxides (NOx), Hydrocarbons Unusual Fire/Explosion Hazards Toxic and irritating gases/fumes may be given off during burning or thermal decomposition. Avoid generating dust; fine dust dispersed in air in sufficient concentrations, and in the presence of an ignition source is a potential dust explosion hazard. 6. Accidental Release Measures Spill and Leak Procedures If molten, allow material to cool and place into an appropriate marked container for disposal. Sweep up and shovel into suitable containers for disposal. Dust deposits should not be allowed to accumulate on surfaces, as these may form an explosive mixture as they are released into the atmosphere in sufficient concentrations. Avoid dispersal of dust in the air (e.g., cleaning dust from surfaces with compressed air). 7. Handling and Storage Handling/Storage Precautions Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 3 of 7 SDS Version: 1.0 Handle in accordance with good industrial hygiene and safety practices. Wash thoroughly after handling. Avoid breathing dust. Containers should be kept tightly closed to prevent contamination. Material is hygroscopic and may absorb small amounts of atmospheric moisture. Minimize dust generation and accumulation. Routine housekeeping should be instituted to ensure that dust does not accumulate on surfaces. Solid particulate can generate electrical charging during operations such as unloading from containers and pneumatic transfer. Provide adequate precautions, such as electrical grounding and bonding, where conductive equipment is involved. Storage Period: Not Established Storage Temperature Maximum: 30 ?C (86 ?F) Substances to Avoid None known. 8. Exposure Controls/Personal Protection Exposure Limits Thermoplastic Polyurethane (TPU) is generally non-hazardous under ambient conditions., The following exposure limits do not apply to the product in its supplied form; however, when the product is heated (i.e, during processing or thermal decomposition conditions), there is a potential for the release of 4,4'- diphenylmethane diisocyanate (MDI) vapors. 4,4'-Diphenylmethane Diisocyanate (MDI) (101-68-8) US. ACGIH Threshold Limit Values Time Weighted Average (TWA): 0.005 ppm US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) Ceiling Limit Value: 0.02 ppm, 0.2 mg/m3 Any component which is listed in section 3 and is not listed in this section does not have a known ACGIH TLV, OSHA PEL or supplier recommended occupational exposure limit. Industrial Hygiene/Ventilation Measures During normal processing, use general dilution and local exhaust as necessary to control airborne vapors, mists, dusts and thermal decomposition products below appropriate airborne concentration standards/guidelines. Special ventilation and personal protective equipment (PPE) is required to control exposure to potentially harmful decomposition products whenever a TPU is heated to temperatures above its decomposition temperature. Examples would include hot knife cutting, grinding, or sawing. Respiratory Protection In the absence of sufficient general dilution or local exhaust ventilation a NIOSH approved air-supplied respirator may be needed during die cleaning, high temperature processing, purging or when thermal decomposition is suspected. Hand Protection Wear heat resistant gloves when handling molten material. Eye Protection Safety glasses with side-shields Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 4 of 7 SDS Version: 1.0 Skin Protection No special skin protection requirements during normal handling and use. Additional Protective Measures Employees should wash their hands and face before eating, drinking, or using tobacco products. Educate and train employees in the safe use and handling of this product. Purgings should be collected as small flat thin shapes or thin strands to allow for rapid cooling. 9. Physical and Chemical Properties State of Matter: solid Appearance: pellets Color: Natural Odor: Odorless Odor Threshold: No Data Available pH: No Data Available Melting Point: 220 ?C (428 ?F) Boiling Point: No Data Available Flash Point: 250 ?C (482 ?F) Evaporation Rate: No Data Available Flammability: No Data Available Lower Explosion Limit: No Data Available Upper Explosion Limit: No Data Available Vapor Pressure: No Data Available Vapor Density: No Data Available Density: 1.1 g/cm? Relative Vapor Density: No Data Available Specific Gravity: 1.1 Solubility in Water: insoluble Partition Coefficient: n- octanol/water: No Data Available Auto-ignition Temperature: > 210 ?C (> 410 ?F) Decomposition Temperature: Decomposition begins at 230 ?C. Softening point: 180 ?C (356 ?F) Dynamic Viscosity: No Data Available Kinematic Viscosity: No Data Available Bulk Density: 500 - 700 kg/m3 Self Ignition: not applicable 10. Stability and Reactivity Hazardous Reactions Hazardous polymerisation does not occur. Stability Stable Materials to Avoid None known. Conditions to Avoid Generation of dust clouds. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 5 of 7 SDS Version: 1.0 Hazardous Decomposition Products By Fire and Thermal Decomposition: Carbon Dioxide ; hydrogen cyanide ; 4,4'-Diphenylmethane Diisocyanate (MDI) ; Aldehydes, Carbon monoxide, Amines, Nitriles, Nitrogen oxides (NOx), Hydrocarbons 11. Toxicological Information Likely Routes of Exposure: Inhalation Skin Contact Eye Contact Health Effects and Symptoms Acute: Contact with heated material can cause thermal burns., Causes a slipping hazard if spilled., Vapors released from thermal decomposition may cause eye irritation with symptoms of burning and tearing, as well as respiratory tract irritation. Toxicity Data for TEXIN DEVELOPMENTAL PRODUCT DP7-1097 000000 In the event of material decomposition due to exceeding the decomposition temperature of this product, release of MDI may occur. Acute Inhalation: The following effects reflect the potential health hazards associated with overexposure to MDI. Diisocyanate vapors or mist at concentrations above the TLV or PEL can irritate (burning sensation) the mucous membranes in the respiratory tract (nose, throat, lungs) causing runny nose, sore throat, coughing, chest discomfort, shortness of breath and reduced lung function (breathing obstruction). Persons with a preexisting, nonspecific bronchial hyperreactivity can respond to concentrations below the TLV or PEL with similar symptoms as well as asthma attack or asthma-like symptoms. Exposure well above the TLV or PEL may lead to bronchitis, bronchial spasm and pulmonary edema (fluid in lungs). Chemical or hypersensitivity pneumonitis, with flu-like symptoms (e.g., fever, chills), has also been reported. These symptoms can be delayed up to several hours after exposure. These effects are usually reversible. Chronic Inhalation: As a result of previous repeated overexposures or a single large dose, certain individuals may develop sensitization to diisocyanates (asthma or asthma-like symptoms) that may cause them to react to a later exposure to diisocyanates at levels well below the TLV or PEL. These symptoms, which can include chest tightness, wheezing, cough, shortness of breath or asthmatic attack, could be immediate or delayed up to several hours after exposure. Extreme asthmatic reactions can be life threatening. Similar to many non- specific asthmatic responses, there are reports that once sensitized an individual can experience these symptoms upon exposure to dust, cold air or other irritants. This increased lung sensitivity can persist for weeks and in severe cases for several years. Sensitization can be permanent. Chronic overexposure to diisocyanates has also been reported to cause lung damage (including fibrosis, decrease in lung function) that may be permanent. Carcinogenicity: No carcinogenic substances as defined by IARC, NTP and/or OSHA 12. Ecological Information No data available for this product. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 6 of 7 SDS Version: 1.0 The components in this product are either non-hazardous or do not have any ecotoxicity data associated with them. 13. Disposal Considerations Waste Disposal Method Waste disposal should be in accordance with existing federal, state and local environmental control laws. 14. Transportation Information Land transport (DOT) Non-Regulated Sea transport (IMDG) Non-Regulated Air transport (ICAO/IATA) Non-Regulated 15. Regulatory Information United States Federal Regulations US. Toxic Substances Control Act: Listed on the TSCA Inventory. US. EPA CERCLA Hazardous Substances (40 CFR 302) Components: None SARA Section 311/312 Hazard Categories: Non-hazardous under Section 311/312 US. EPA Emergency Planning and Community Right-To-Know Act (EPCRA) SARA Title III Section 302 Extremely Hazardous Substance (40 CFR 355, Appendix A) Components: None US. EPA Emergency Planning and Community Right-To-Know Act (EPCRA) SARA Title III Section 313 Toxic Chemicals (40 CFR 372.65) - Supplier Notification Required Components: None US. EPA Resource Conservation and Recovery Act (RCRA) Composite List of Hazardous Wastes and Appendix VIII Hazardous Constituents (40 CFR 261): Under RCRA, it is the responsibility of the person who generates a solid waste, as defined in 40 CFR 261.2, to determine if that waste is a hazardous waste. State Right-To-Know Information The following chemicals are specifically listed by individual states; other product specific health and safety data in other sections of the MSDS may also be applicable for state requirements. For details on your regulatory requirements you should contact the appropriate agency in your state. Massachusetts, New Jersey or Pennsylvania Right to Know Substance Lists: Weight percent Components CAS-No. Material Name: TEXIN DEVELOPMENTAL PRODUCT DP7- 1097 000000 Material Number: 603489 Page: 7 of 7 SDS Version: 1.0 >=1% Polyurethane polyester elastomer 26375-23-5 California Prop. 65: To the best of our knowledge, this product does not contain any of the listed chemicals, which the state of California has found to cause cancer, birth defects or other reproductive harm. Based on information provided by our suppliers, this product is considered ?DRC Conflict Free? as defined by the SEC Conflict Minerals Final Rule (Release No. 34-67716; File No. S7-40-10; Date: 2012-08-22). 16. Other Information The method of hazard communication for Bayer MaterialScience LLC is comprised of Product Labels and Safety Data Sheets. Contact: Product Safety Department Telephone: (412) 777-2835 SDS Number: 112000009385 Version Date: 03/13/2015 SDS Version: 1.0 This information is furnished without warranty, express or implied. This information is believed to be accurate to the best knowledge of Bayer MaterialScience LLC. The information in this SDS relates only to the specific material designated herein. Bayer MaterialScience LLC assumes no legal responsibility for use of or reliance upon the information in this SDS. jbartel Text Box Bay State Polymer
27540 Detroit Road, Suite 102
Westlake, OH 44145
Phone: 440-892-8500
Fax: 440-892-8436 1. Identification 2. Hazards Identification 3. Composition/Information on Ingredients 4. First Aid Measures 5. Firefighting Measures 6. Accidental Release Measures 7. Handling and Storage 8. Exposure Controls/Personal Protection 9. Physical and Chemical Properties 10. Stability and Reactivity 11. Toxicological Information 12. Ecological Information 13. Disposal Considerations 14. Transportation Information 15. Regulatory Information 16. Other Information