3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 1 of 9 Safety Data Sheet Copyright,2014,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 28-0047-2 Version Number: 1.05 Issue Date: 05/29/14 Supercedes Date: 02/28/14 SECTION 1: Identification 1.1. Product identifier 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 1.2. Recommended use and restrictions on use Recommended use Abrasive Product 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification 2.1. Hazard classification Not classified as hazardous according to OSHA Hazard Communication Standard, 29 CFR 1910.1200. 2.2. Label elements Signal word Not applicable. Symbols Not applicable. Pictograms Not applicable. 2.3. Hazards not otherwise classified None. 94% of the mixture consists of ingredients of unknown acute oral toxicity. 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 2 of 9 SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Silicon Carbide Mineral 409-21-2 2 - 10 Synthetic amorphous silica, fumed, crystalline free 112945-52-5 0.01 - 0.2 Cured Resin Mixture 15 - 65 Film Backings Mixture 5 - 25 Polyurethane Foam Mixture 15 - 40 Loop Backing Mixture 10 - 30 SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Wash with soap and water. If signs/symptoms develop, get medical attention. Eye Contact: Flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. If signs/symptoms persist, get medical attention. If Swallowed: No need for first aid is anticipated. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion 5.3. Special protective actions for fire-fighters No unusual fire or explosion hazards are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 3 of 9 Observe precautions from other sections. 6.2. Environmental precautions Not applicable. 6.3. Methods and material for containment and cleaning up Not applicable. SECTION 7: Handling and storage 7.1. Precautions for safe handling For industrial or professional use only. Avoid breathing of dust created by sanding, grinding or machining. Damaged product can break apart during use and cause serious injury to face or eyes. Check product for damage such as cracks or nicks prior to use. Replace if damaged. Always wear eye and face protection when working at sanding or grinding operations or when near such operations. Combustible dust may form by action of this product on another material (substrate). Dust generated from the substrate during use of this product may be explosive if in sufficient concentration with an ignition source. Dust deposits should not be allowed to accumulate on surfaces because of the potential for secondary explosions. 7.2. Conditions for safe storage including any incompatibilities No special storage requirements. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits Ingredient C.A.S. No. Agency Limit type Additional Comments SILICA, AMORPHOUS 112945-52- 5 OSHA TWA concentration:0.8 mg/m3;TWA:20 millions of particles/cu. ft. Silicon Carbide Mineral 409-21-2 ACGIH TWA(as fiber):0.1 fiber/cc;TWA(inhalable fraction):10 mg/m3;TWA(respirable fraction):3 mg/m3 Silicon Carbide Mineral 409-21-2 OSHA TWA(as total dust):15 mg/m3;TWA(respirable fraction):5 mg/m3 ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Provide local exhaust at process emission sources to control exposure near the source and to prevent the escape of dust into the work area. Ensure that dust-handling systems (such as exhaust ducts, dust collectors, vessels, and processing equipment) are designed in a manner to prevent the escape of dust into the work area (i.e., there is no leakage from the equipment). 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 4 of 9 8.2.2. Personal protective equipment (PPE) Eye/face protection To minimize the risk of injury to face and eyes, always wear eye and face protection when working at sanding or grinding operations or when near such operations. Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Safety Glasses with side shields Skin/hand protection Wear appropriate gloves to minimize risk of injury to skin from contact with dust or physical abrasion from grinding or sanding. Respiratory protection Assess exposure concentrations of all materials involved in the work process. Consider material being abraded when determining the appropriate respiratory protection. Select and use appropriate respirators to prevent inhalation overexposure. An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Solid Odor, Color, Grade: Solid Abrasive Product Odor threshold Not Applicable pH Not Applicable Melting point Not Applicable Boiling Point Not Applicable Flash Point Not Applicable Evaporation rate Not Applicable Flammability (solid, gas) Not Classified Flammable Limits(LEL) Not Applicable Flammable Limits(UEL) Not Applicable Vapor Pressure Not Applicable Vapor Density Not Applicable Specific Gravity Not Applicable Solubility In Water Not Applicable Solubility- non-water Not Applicable Partition coefficient: n-octanol/ water Not Applicable Autoignition temperature Not Applicable Decomposition temperature Not Applicable Viscosity Not Applicable 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 5 of 9 SECTION 10: Stability and reactivity 10.1. Reactivity This material is considered to be non reactive under normal use conditions. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid None known. 10.5. Incompatible materials None known. 10.6. Hazardous decomposition products Substance Condition None known. Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: Dust from grinding, sanding or machining may cause irritation of the respiratory system. Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Mechanical Skin irritation: Signs/symptoms may include abrasion, redness, pain, and itching. Allergic Skin Reaction (non-photo induced) in sensitive people: Signs/symptoms may include redness, swelling, blistering, and itching. Eye Contact: Mechanical eye irritation: Signs/symptoms may include pain, redness, tearing and corneal abrasion. 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 6 of 9 Dust created by grinding, sanding, or machining may cause eye irritation. Signs/symptoms may include redness, swelling, pain, tearing, and blurred or hazy vision. Ingestion: No health effects are expected. Additional Information: This document covers only the 3M product. For complete assessment, when determining the degree of hazard, the material being abraded must also be considered. Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Ingestion No data available; calculated ATE > 5,000 mg/kg Silicon Carbide Mineral Dermal Rat LD50 > 2,000 mg/kg Silicon Carbide Mineral Ingestion Rat LD50 > 2,000 mg/kg Synthetic amorphous silica, fumed, crystalline free Dermal Rabbit LD50 > 5,000 mg/kg Synthetic amorphous silica, fumed, crystalline free Inhalation- Dust/Mist (4 hours) Rat LC50 > 0.691 mg/l Synthetic amorphous silica, fumed, crystalline free Ingestion Rat LD50 > 5,110 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value Synthetic amorphous silica, fumed, crystalline free Rabbit No significant irritation Serious Eye Damage/Irritation Name Species Value Synthetic amorphous silica, fumed, crystalline free Rabbit No significant irritation Skin Sensitization Name Species Value Synthetic amorphous silica, fumed, crystalline free Human and animal Not sensitizing Respiratory Sensitization Name Species Value Germ Cell Mutagenicity Name Route Value Synthetic amorphous silica, fumed, crystalline free In Vitro Not mutagenic Carcinogenicity Name Route Species Value Synthetic amorphous silica, fumed, crystalline free Not Specified Mouse Some positive data exist, but the data are not sufficient for classification Reproductive Toxicity Reproductive and/or Developmental Effects Name Route Value Species Test Result Exposure Duration Synthetic amorphous silica, fumed, crystalline free Ingestion Not toxic to female reproduction Rat NOAEL 509 mg/kg/day 1 generation 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 7 of 9 Synthetic amorphous silica, fumed, crystalline free Ingestion Not toxic to male reproduction Rat NOAEL 497 mg/kg/day 1 generation Synthetic amorphous silica, fumed, crystalline free Ingestion Not toxic to development Rat NOAEL 1,350 mg/kg/day during organogenesi s Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Silicon Carbide Mineral Inhalation pneumoconiosis Some positive data exist, but the data are not sufficient for classification HHA Synthetic amorphous silica, fumed, crystalline free Inhalation respiratory system | silicosis All data are negative Human NOAEL Not available occupational exposure Aspiration Hazard Name Value Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Prior to disposal, consult all applicable authorities and regulations to insure proper classification. The substrate that was abraded must be considered as a factor in the disposal method for this product. Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. If no other disposal options are available, waste product may be placed in a landfill properly designed for industrial waste. EPA Hazardous Waste Number (RCRA): Not regulated SECTION 14: Transport Information Not regulated per U.S. DOT, IATA or IMO. 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 8 of 9 These transportation classifications are provided as a customer service. As the shipper YOU remain responsible for complying with all applicable laws and regulations, including proper transportation classification and packaging. 3M transportation classifications are based on product formulation, packaging, 3M policies and 3M understanding of applicable current regulations. 3M does not guarantee the accuracy of this classification information. This information applies only to transportation classification and not the packaging, labeling, or marking requirements. The original 3M package is certified for U.S. ground shipment only. If you are shipping by air or ocean, the package may not meet applicable regulatory requirements. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information. 311/312 Hazard Categories: Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Immediate Hazard - No Delayed Hazard - No 15.2. State Regulations Contact 3M for more information. 15.3. Chemical Inventories This product is an article as defined by TSCA regulations, and is exempt from TSCA Inventory listing requirements. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 0 Flammability: 1 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. HMIS Hazard Classification Health: 0 Flammability: 1 Physical Hazard: 0 Personal Protection: X - See PPE section. Hazardous Material Identification System (HMIS? III) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS? III ratings are to be used with a fully implemented HMIS? III program. HMIS? is a registered mark of the American Coatings Association (ACA). Document Group: 28-0047-2 Version Number: 1.05 Issue Date: 05/29/14 Supercedes Date: 02/28/14 3M? Abrasive Products, Trizact? 443SA ZW A14 Hookit? 05/29/14 __________________________________________________________________________________________ Page 9 of 9 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued. 3M MAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE. User is responsible for determining whether the 3M product is fit for a particular purpose and suitable for user's method of use or application. Given the variety of factors that can affect the use and application of a 3M product, some of which are uniquely within the user's knowledge and control, it is essential that the user evaluate the 3M product to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3M provides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information, 3M makes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from 3M 3M USA SDSs are available at www.3M.com