FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Not available. Liquid. INFOTRAC 1-800-535-5053 SAFETY DATA SHEET GHS product identifier Other means of identification Product type Emergency telephone number Section 1. Identification : : : : Supplier's details : Factory Motor Parts 1380 Corporate Center Curve, Suite 200 Eagan, MN 55121 866-387-3343 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Relevant identified uses of the substance or mixture and uses advised against Identified uses None known. Uses advised against Reason Industrial applications: Lubricating Oil Product code : ATFMVFS-55GAL Section 2. Hazards identification AQUATIC HAZARD (ACUTE) - Category 3Classification of the substance or mixture : Signal word : Hazard statements : Harmful to aquatic life. Precautionary statements Prevention : Avoid release to the environment. Response : Not applicable. Storage : Not applicable. Disposal : Dispose of contents and container in accordance with all local, regional, national and international regulations. GHS label elements Percentage of the mixture consisting of ingredient(s) of unknown hazards to the aquatic environment: 3.7% General : Read label before use. Keep out of reach of children. If medical advice is needed, have product container or label at hand. OSHA/HCS status : While this material is not considered hazardous by the OSHA Hazard Communication Standard (29 CFR 1910.1200), this SDS contains valuable information critical to the safe handling and proper use of the product. This SDS should be retained and available for employees and other users of this product. Hazards not otherwise classified : None known. No signal word. Date of issue/Date of revision : 04/21/2020 Version : 1.01 1/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 3. Composition/information on ingredients There are no additional ingredients present which, within the current knowledge of the supplier and in the concentrations applicable, are classified as hazardous to health or the environment and hence require reporting in this section. Other means of identification : Not available. Substance/mixture : Occupational exposure limits, if available, are listed in Section 8. Mixture Any concentration shown as a range is to protect confidentiality or is due to batch variation. Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based ?75 - ?90 72623-87-1 Distillates (petroleum), hydrotreated heavy paraffinic ?4.7 64742-54-7 Distillates (petroleum), solvent-dewaxed heavy paraffinic ?4.7 64742-65-0 Distillates (petroleum), solvent-dewaxed light paraffinic ?4.7 64742-56-9 Distillates (petroleum), hydrotreated light paraffinic ?3 64742-55-8 Substituted hydrocarbyl sulfide <1 Proprietary Ingredient name CAS number% Wash out mouth with water. Remove dentures if any. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If material has been swallowed and the exposed person is conscious, give small quantities of water to drink. Stop if the exposed person feels sick as vomiting may be dangerous. Do not induce vomiting unless directed to do so by medical personnel. If vomiting occurs, the head should be kept low so that vomit does not enter the lungs. Get medical attention if adverse health effects persist or are severe. Never give anything by mouth to an unconscious person. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Immediately flush eyes with plenty of water, occasionally lifting the upper and lower eyelids. Check for and remove any contact lenses. Continue to rinse for at least 10 minutes. Get medical attention if irritation occurs. Flush contaminated skin with plenty of water. Remove contaminated clothing and shoes. Get medical attention if symptoms occur. Wash clothing before reuse. Clean shoes thoroughly before reuse. Remove victim to fresh air and keep at rest in a position comfortable for breathing. If not breathing, if breathing is irregular or if respiratory arrest occurs, provide artificial respiration or oxygen by trained personnel. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Get medical attention if adverse health effects persist or are severe. If unconscious, place in recovery position and get medical attention immediately. Maintain an open airway. Loosen tight clothing such as a collar, tie, belt or waistband. Section 4. First aid measures Eye contact Skin contact Inhalation Ingestion : : : : Description of necessary first aid measures Most important symptoms/effects, acute and delayed Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact Over-exposure signs/symptoms Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Potential acute health effects Date of issue/Date of revision : 04/21/2020 Version : 1.01 2/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 4. First aid measures Protection of first-aiders : No action shall be taken involving any personal risk or without suitable training. It may be dangerous to the person providing aid to give mouth-to-mouth resuscitation. Notes to physician : Treat symptomatically. Contact poison treatment specialist immediately if large quantities have been ingested or inhaled. Specific treatments : No specific treatment. See toxicological information (Section 11) Indication of immediate medical attention and special treatment needed, if necessary Section 5. Fire-fighting measures Promptly isolate the scene by removing all persons from the vicinity of the incident if there is a fire. No action shall be taken involving any personal risk or without suitable training. Hazardous thermal decomposition products Specific hazards arising from the chemical Decomposition products may include the following materials: carbon dioxide carbon monoxide In a fire or if heated, a pressure increase will occur and the container may burst. This material is harmful to aquatic life. Fire water contaminated with this material must be contained and prevented from being discharged to any waterway, sewer or drain. Fire-fighters should wear appropriate protective equipment and self-contained breathing apparatus (SCBA) with a full face-piece operated in positive pressure mode. Special protective equipment for fire-fighters Use an extinguishing agent suitable for the surrounding fire. Extinguishing media : : : Do not use water jet. Suitable extinguishing media : Unsuitable extinguishing media : Special protective actions for fire-fighters : Section 6. Accidental release measures Environmental precautions Personal precautions, protective equipment and emergency procedures : : No action shall be taken involving any personal risk or without suitable training. Evacuate surrounding areas. Keep unnecessary and unprotected personnel from entering. Do not touch or walk through spilled material. Avoid breathing vapor or mist. Provide adequate ventilation. Wear appropriate respirator when ventilation is inadequate. Put on appropriate personal protective equipment. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. Inform the relevant authorities if the product has caused environmental pollution (sewers, waterways, soil or air). Water polluting material. May be harmful to the environment if released in large quantities. Stop leak if without risk. Move containers from spill area. Dilute with water and mop up if water-soluble. Alternatively, or if water-insoluble, absorb with an inert dry material and place in an appropriate waste disposal container. Dispose of via a licensed waste disposal contractor. Small spill : Methods and materials for containment and cleaning up For non-emergency personnel For emergency responders : If specialized clothing is required to deal with the spillage, take note of any information in Section 8 on suitable and unsuitable materials. See also the information in "For non- emergency personnel". Date of issue/Date of revision : 04/21/2020 Version : 1.01 3/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 6. Accidental release measures Stop leak if without risk. Move containers from spill area. Approach release from upwind. Prevent entry into sewers, water courses, basements or confined areas. Wash spillages into an effluent treatment plant or proceed as follows. Contain and collect spillage with non-combustible, absorbent material e.g. sand, earth, vermiculite or diatomaceous earth and place in container for disposal according to local regulations (see Section 13). Dispose of via a licensed waste disposal contractor. Contaminated absorbent material may pose the same hazard as the spilled product. Note: see Section 1 for emergency contact information and Section 13 for waste disposal. Large spill : Section 7. Handling and storage Advice on general occupational hygiene Conditions for safe storage, including any incompatibilities Eating, drinking and smoking should be prohibited in areas where this material is handled, stored and processed. Workers should wash hands and face before eating, drinking and smoking. Remove contaminated clothing and protective equipment before entering eating areas. See also Section 8 for additional information on hygiene measures. Store in accordance with local regulations. Store in original container protected from direct sunlight in a dry, cool and well-ventilated area, away from incompatible materials (see Section 10) and food and drink. Keep container tightly closed and sealed until ready for use. Containers that have been opened must be carefully resealed and kept upright to prevent leakage. Do not store in unlabeled containers. Use appropriate containment to avoid environmental contamination. See Section 10 for incompatible materials before handling or use. : : Protective measures Put on appropriate personal protective equipment (see Section 8). Do not ingest. Avoid contact with eyes, skin and clothing. Avoid breathing vapor or mist. Avoid release to the environment. Keep in the original container or an approved alternative made from a compatible material, kept tightly closed when not in use. Empty containers retain product residue and can be hazardous. Do not reuse container. : Precautions for safe handling Section 8. Exposure controls/personal protection Control parameters Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based NIOSH REL (United States, 10/2016). TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), hydrotreated heavy paraffinic ACGIH TLV (United States, 3/2019). TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2016). TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed heavy paraffinic ACGIH TLV (United States, 3/2019). TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2016). TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), solvent-dewaxed light paraffinic ACGIH TLV (United States, 3/2019). TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2016). Ingredient name Exposure limits Occupational exposure limits Date of issue/Date of revision : 04/21/2020 Version : 1.01 4/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 8. Exposure controls/personal protection Hand protection Based on the hazard and potential for exposure, select a respirator that meets the appropriate standard or certification. Respirators must be used according to a respiratory protection program to ensure proper fitting, training, and other important aspects of use. Chemical-resistant, impervious gloves complying with an approved standard should be worn at all times when handling chemical products if a risk assessment indicates this is necessary. Considering the parameters specified by the glove manufacturer, check during use that the gloves are still retaining their protective properties. It should be noted that the time to breakthrough for any glove material may be different for different glove manufacturers. In the case of mixtures, consisting of several substances, the protection time of the gloves cannot be accurately estimated. Safety eyewear complying with an approved standard should be used when a risk assessment indicates this is necessary to avoid exposure to liquid splashes, mists, gases or dusts. If contact is possible, the following protection should be worn, unless the assessment indicates a higher degree of protection: safety glasses with side- shields. Eye/face protection Respiratory protection : : : Body protection Personal protective equipment for the body should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. : Environmental exposure controls : Emissions from ventilation or work process equipment should be checked to ensure they comply with the requirements of environmental protection legislation. In some cases, fume scrubbers, filters or engineering modifications to the process equipment will be necessary to reduce emissions to acceptable levels. Appropriate engineering controls : Good general ventilation should be sufficient to control worker exposure to airborne contaminants. Wash hands, forearms and face thoroughly after handling chemical products, before eating, smoking and using the lavatory and at the end of the working period. Appropriate techniques should be used to remove potentially contaminated clothing. Wash contaminated clothing before reusing. Ensure that eyewash stations and safety showers are close to the workstation location. Hygiene measures : Individual protection measures Skin protection Other skin protection : Appropriate footwear and any additional skin protection measures should be selected based on the task being performed and the risks involved and should be approved by a specialist before handling this product. TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Distillates (petroleum), hydrotreated light paraffinic ACGIH TLV (United States, 3/2019). TWA: 5 mg/m? 8 hours. Form: Inhalable fraction OSHA PEL (United States, 5/2018). TWA: 5 mg/m? 8 hours. NIOSH REL (United States, 10/2016). TWA: 5 mg/m? 10 hours. Form: Mist STEL: 10 mg/m? 15 minutes. Form: Mist Substituted hydrocarbyl sulfide None. Section 9. Physical and chemical properties Physical state Melting point Liquid. Not available. Not available.Odor pH Clear. Red.Color Not available. Not available.Odor threshold : : : : : : Appearance Date of issue/Date of revision : 04/21/2020 Version : 1.01 5/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 9. Physical and chemical properties Vapor pressure Relative density Vapor density Solubility 0.8471 Not available. Not available. Insoluble in the following materials: cold water and hot water. Evaporation rate Not available. Auto-ignition temperature Flash point Not available. Open cup: 224?C (435.2?F) [Cleveland.] Not available. Viscosity Kinematic (40?C (104?F)): 0.2935 cm2/s (29.35 cSt) Partition coefficient: n- octanol/water : : : : : : : : : Boiling point : Not available. Flammability (solid, gas) : Not available. Lower and upper explosive (flammable) limits : Not available. Decomposition temperature : Not available. Solubility in water : Not available. Flow time (ISO 2431) : Not available. Pour point : -45?C (-49?F) Section 10. Stability and reactivity Hazardous decomposition products Conditions to avoid No specific data. Under normal conditions of storage and use, hazardous decomposition products should not be produced. The product is stable.Chemical stability No specific data. : : : Incompatible materials : Possibility of hazardous reactions : Under normal conditions of storage and use, hazardous reactions will not occur. Reactivity : No specific test data related to reactivity available for this product or its ingredients. Section 11. Toxicological information Acute toxicity Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), hydrotreated heavy paraffinic LC50 Inhalation Dusts and mists Rat 5.7 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed heavy paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), solvent-dewaxed light LD50 Dermal Rabbit >5000 mg/kg - Product/ingredient name Result Species Dose Exposure Information on toxicological effects Date of issue/Date of revision : 04/21/2020 Version : 1.01 6/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 11. Toxicological information paraffinic LD50 Dermal Rat >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Distillates (petroleum), hydrotreated light paraffinic LC50 Inhalation Dusts and mists Rat >5.53 mg/l 4 hours LD50 Dermal Rabbit >2000 mg/kg - LD50 Oral Rat >5000 mg/kg - Carcinogenicity Not available. Mutagenicity Not available. Teratogenicity Not available. Reproductive toxicity Not available. Irritation/Corrosion Not available. Sensitization Not available. Information on the likely routes of exposure Inhalation : No known significant effects or critical hazards. No known significant effects or critical hazards.:Ingestion Skin contact : No known significant effects or critical hazards. No known significant effects or critical hazards.:Eye contact Symptoms related to the physical, chemical and toxicological characteristics Skin contact Ingestion Inhalation No specific data. No specific data. No specific data. : : : Eye contact : No specific data. Delayed and immediate effects and also chronic effects from short and long term exposure Specific target organ toxicity (single exposure) Specific target organ toxicity (repeated exposure) Not available. Not available. Aspiration hazard Name Result Distillates (petroleum), solvent-dewaxed light paraffinic ASPIRATION HAZARD - Category 1 Distillates (petroleum), hydrotreated light paraffinic ASPIRATION HAZARD - Category 1 : Not available. Potential acute health effects Potential immediate effects : Not available. Short term exposure Potential delayed effects : Not available. Long term exposure Date of issue/Date of revision : 04/21/2020 Version : 1.01 7/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 11. Toxicological information Not available. No known significant effects or critical hazards.General : No known significant effects or critical hazards.Carcinogenicity : No known significant effects or critical hazards.Mutagenicity : No known significant effects or critical hazards.Teratogenicity : Developmental effects : No known significant effects or critical hazards. Fertility effects : No known significant effects or critical hazards. Potential chronic health effects Potential immediate effects : Not available. Potential delayed effects : Not available. Numerical measures of toxicity Acute toxicity estimates Product/ingredient name Bel-Ray ATF MV Full Syn Multi-Vehicle N/A 2566.6 N/A N/A N/A Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated heavy paraffinic N/A 2500 N/A N/A 5.7 Distillates (petroleum), solvent-dewaxed heavy paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), solvent-dewaxed light paraffinic N/A 2500 N/A N/A N/A Distillates (petroleum), hydrotreated light paraffinic N/A 2500 N/A N/A N/A Oral (mg/ kg) Dermal (mg/kg) Inhalation (gases) (ppm) Inhalation (vapors) (mg/l) Inhalation (dusts and mists) (mg/ l) Section 12. Ecological information Toxicity Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Crustaceans 48 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), hydrotreated heavy paraffinic Acute EC50 >100 mg/l Daphnia 48 hours Acute IC50 >100 mg/l Algae 72 hours Acute LC50 >100 mg/l Fish 96 hours Distillates (petroleum), solvent-dewaxed heavy paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Chronic NOEL >1 mg/l Daphnia 21 days Distillates (petroleum), hydrotreated light paraffinic Acute EC50 >100 mg/l Algae 72 hours Acute EC50 >100 mg/l Daphnia 48 hours Acute LC50 >100 mg/l Fish 96 hours Substituted hydrocarbyl sulfide EC50 >100 mg/l Algae 4 days EC50 0.58 mg/l Daphnia 2 days LC50 0.75 mg/l Fish 4 days Product/ingredient name SpeciesResult Exposure Date of issue/Date of revision : 04/21/2020 Version : 1.01 8/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 12. Ecological information LogPow BCF Potential Bioaccumulative potential Other adverse effects : No known significant effects or critical hazards. Product/ingredient name Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based >6 - high Distillates (petroleum), hydrotreated heavy paraffinic >6 - high Distillates (petroleum), solvent-dewaxed heavy paraffinic 2 to 6 - high Distillates (petroleum), hydrotreated light paraffinic >6 - high Product/ingredient name Aquatic half-life Photolysis Biodegradability Lubricating oils (petroleum), C20-50, hydrotreated neutral oil-based - - Inherent Distillates (petroleum), hydrotreated heavy paraffinic - - Not readily Distillates (petroleum), hydrotreated light paraffinic - - Inherent Substituted hydrocarbyl sulfide - - Not readily NOEC 100 mg/l Algae 4 days NOEC 0.32 mg/l Daphnia 2 days NOEC 0.56 mg/l Fish 4 days Persistence and degradability Substituted hydrocarbyl sulfide OECD 301F Ready Biodegradability - Manometric Respirometry Test 5.9 % - Not readily - 28 days - - Product/ingredient name Test DoseResult Inoculum Soil/water partition coefficient (KOC) : Not available. Mobility in soil Section 13. Disposal considerations The generation of waste should be avoided or minimized wherever possible. Disposal of this product, solutions and any by-products should at all times comply with the requirements of environmental protection and waste disposal legislation and any regional local authority requirements. Dispose of surplus and non-recyclable products via a licensed waste disposal contractor. Waste should not be disposed of untreated to the sewer unless fully compliant with the requirements of all authorities with jurisdiction. Waste packaging should be recycled. Incineration or landfill should only be considered when recycling is not feasible. This material and its container must be disposed of in a safe way. Care should be taken when handling emptied containers that have not been cleaned or rinsed out. Empty containers or liners may retain some product residues. Avoid dispersal of spilled material and runoff and contact with soil, waterways, drains and sewers. :Disposal methods RCRA classification : Not Regulated Date of issue/Date of revision : 04/21/2020 Version : 1.01 9/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 14. Transport information Not regulated.Not regulated. Not regulated. DOT Classification IMDG IATA UN number TDG Classification Not regulated. Special precautions for user Transport in bulk according to Annex II of MARPOL and the IBC Code Transport within user?s premises: always transport in closed containers that are upright and secure. Ensure that persons transporting the product know what to do in the event of an accident or spillage. : Not available. : Section 15. Regulatory information U.S. Federal regulations The following components are listed: MINERAL OIL, PETROLEUM DISTILLATES, SOLVENT-DEWAXED LIGHT PARAFFINIC; MINERAL OIL, PETROLEUM DISTILLATES, HYDROTREATED LIGHT PARAFFINIC; OIL MIST, MINERAL; OIL MIST, MINERAL; OIL MIST, MINERAL TSCA 4(a) proposed test rules: dibutyl phosphonate Clean Water Act (CWA) 307: toluene; ethylbenzene Clean Water Act (CWA) 311: toluene; xylene; ethylbenzene Massachusetts : : Clean Air Act Section 112 (b) Hazardous Air Pollutants (HAPs) : Listed Clean Air Act Section 602 Class I Substances : Not listed Clean Air Act Section 602 Class II Substances : Not listed DEA List I Chemicals (Precursor Chemicals) : Not listed DEA List II Chemicals (Essential Chemicals) : Not listed New York : None of the components are listed. State regulations TSCA 8(a) CDR Exempt/Partial exemption: Not determined TSCA 8(c) calls for record of SAR: trimethyl phosphate SARA 302/304 SARA 304 RQ : Not applicable. No products were found. Composition/information on ingredients SARA 311/312 Classification : Not applicable. Distillates (petroleum), solvent- dewaxed light paraffinic ?4.7 ASPIRATION HAZARD - Category 1 Distillates (petroleum), hydrotreated light paraffinic ?3 ASPIRATION HAZARD - Category 1 Name % Classification Composition/information on ingredients Date of issue/Date of revision : 04/21/2020 Version : 1.01 10/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 15. Regulatory information Viet Nam California Prop. 65 New Jersey : The following components are listed: MINERAL OIL (UNTREATED and MILDLY TREATED) Pennsylvania : None of the components are listed. International lists National inventory Australia : All components are listed or exempted. Canada : All components are listed or exempted. China : All components are listed or exempted. Europe : All components are listed or exempted. Japan : Japan inventory (ENCS): All components are listed or exempted. Japan inventory (ISHL): Not determined. Republic of Korea : All components are listed or exempted. New Zealand : All components are listed or exempted. Philippines : All components are listed or exempted. Taiwan : All components are listed or exempted. Turkey : Not determined. United States : All components are listed or exempted. Thailand : Not determined. WARNING: This product can expose you to chemicals including Trimethyl phosphate, which is known to the State of California to cause cancer, and Toluene, which is known to the State of California to cause birth defects or other reproductive harm. For more information go to www.P65Warnings.ca.gov. Trimethyl phosphate 0.0057908 Yes. - Ethylbenzene 0.00125 Yes. - Toluene 0.0001364 - Yes. Ingredient name No significant risk level Maximum acceptable dosage level : Not determined. Concentration (% ) Information provided is based on industrial use and may not be relevant to consumer applications. Section 16. Other information History Date of issue/Date of revision Version : : Indicates information that has changed from previously issued version. Key to abbreviations : 04/21/2020 1.01 Procedure used to derive the classification Classification Justification Aquatic Acute 3, H402 Calculation method ATE = Acute Toxicity Estimate BCF = Bioconcentration Factor GHS = Globally Harmonized System of Classification and Labelling of Chemicals IATA = International Air Transport Association IBC = Intermediate Bulk Container IMDG = International Maritime Dangerous Goods LogPow = logarithm of the octanol/water partition coefficient MARPOL = International Convention for the Prevention of Pollution From Ships, 1973 as modified by the Protocol of 1978. ("Marpol" = marine pollution) N/A = Not available SGG = Segregation Group UN = United Nations Date of issue/Date of revision : 04/21/2020 Version : 1.01 11/12 FVP FULL SYNTHETIC MULTI-VEHICLE ATF 55 GAL Section 16. Other information To the best of our knowledge, the information contained herein is accurate. However, neither the above-named supplier, nor any of its subsidiaries, assumes any liability whatsoever for the accuracy or completeness of the information contained herein. Final determination of suitability of any material is the sole responsibility of the user. All materials may present unknown hazards and should be used with caution. Although certain hazards are described herein, we cannot guarantee that these are the only hazards that exist. Notice to reader Date of issue/Date of revision : 04/21/2020 Version : 1.01 12/12