SAFETY DATA SHEET 1. Identification Copper-Coat? Gasket CompoundProduct identifier Other means of identification 401612Product code Gasket compoundRecommended use None known.Recommended restrictions Manufacturer/Importer/Supplier/Distributor information Manufactured or sold by: Company name CRC Industries, Inc. Address 885 Louis Dr. Warminster, PA 18974 US Telephone General Information 215-674-4300 Technical Assistance 800-521-3168 Customer Service 800-272-4620 24-Hour Emergency 800-424-9300 (US) (CHEMTREC) 703-527-3887 (International) Website www.crcindustries.com 2. Hazard(s) identification Category 1Flammable aerosolsPhysical hazards Compressed gasGases under pressure Category 2Skin corrosion/irritationHealth hazards Category 2Serious eye damage/eye irritation Category 2Carcinogenicity Category 2Reproductive toxicity (the unborn child) Category 3 respiratory tract irritationSpecific target organ toxicity, single exposure Category 3 narcotic effectsSpecific target organ toxicity, single exposure Category 2Specific target organ toxicity, repeated exposure Category 1Aspiration hazard Category 2Hazardous to the aquatic environment, acute hazard Environmental hazards Not classified.OSHA defined hazards Label elements Signal word Danger Hazard statement Extremely flammable aerosol. Contains gas under pressure; may explode if heated. May be fatal if swallowed and enters airways. Causes skin irritation. Causes serious eye irritation. May cause respiratory irritation. May cause drowsiness or dizziness. Suspected of causing cancer. Suspected of damaging the unborn child. May cause damage to organs through prolonged or repeated exposure. Toxic to aquatic life. 1 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US Precautionary statement Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Do not apply while equipment is energized. Pressurized container: Do not pierce or burn, even after use. Extinguish all flames, pilot lights and heaters. Vapors will accumulate readily and may ignite. Use only with adequate ventilation; maintain ventilation during use and until all vapors are gone. Open doors and windows or use other means to ensure a fresh air supply during use and while product is drying. If you experience any symptoms listed on this label, increase ventilation or leave the area. Do not breathe mist or vapor. Wash thoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection. Avoid release to the environment. Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Wash with plenty of water. If skin irritation occurs: Get medical attention. Take off contaminated clothing and wash before reuse. If inhaled: Remove person to fresh air and keep comfortable for breathing. Call a poison center/doctor if you feel unwell. If in eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical attention. If exposed or concerned: Get medical attention. Storage Store in a well-ventilated place. Store locked up. Protect from sunlight. Do not expose to temperatures exceeding 50?C/122?F. Exposure to high temperature may cause can to burst. Disposal Dispose of contents/container in accordance with local/regional/national regulations. Hazard(s) not otherwise classified (HNOC) None known. 3. Composition/information on ingredients Mixtures CAS number %Common name and synonymsChemical name 67-64-1Acetone 30 - 40 106-97-8n-Butane 20 - 30 78-93-3Methyl ethyl ketone 10 - 20 74-98-6Propane 5 - 10 108-88-3Toluene 5 - 10 7440-50-8Copper 1 - 3 108-10-1Methyl isobutyl ketone < 1 Specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing. Keep victim warm. Call a POISON CENTER or doctor/physician if you feel unwell. Inhalation Remove contaminated clothing. Wash with plenty of soap and water. Take off contaminated clothing and wash before reuse. If skin irritation occurs: Get medical advice/attention. Skin contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Get medical attention if irritation develops and persists. Eye contact Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Ingestion May cause drowsiness and dizziness. Headache. Nausea, vomiting. Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause respiratory irritation. Skin irritation. May cause redness and pain. Prolonged exposure may cause chronic effects. Most important symptoms/effects, acute and delayed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. Indication of immediate medical attention and special treatment needed IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance. General information 5. Fire-fighting measures Alcohol resistant foam. Water fog. Dry chemical powder. Dry chemicals. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing media 2 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US Contents under pressure. Pressurized container may rupture when exposed to heat or flame. During fire, gases hazardous to health may be formed. Specific hazards arising from the chemical Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. Special protective equipment and precautions for firefighters Fire-fighting equipment/instructions In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. Extremely flammable aerosol. Contents under pressure. Pressurized container may rupture when exposed to heat or flame. General fire hazards 6. Accidental release measures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Many vapors are heavier than air and will spread along ground and collect in low or confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Emergency personnel need self-contained breathing equipment. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Personal precautions, protective equipment and emergency procedures Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop the flow of material, if this is without risk. Prevent product from entering drains. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder sawdust). Methods and materials for containment and cleaning up Avoid release to the environment. Prevent further leakage or spillage if safe to do so. Avoid discharge into drains, water courses or onto the ground. Inform appropriate managerial or supervisory personnel of all environmental releases. Environmental precautions 7. Handling and storage Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The metal container will conduct electricity if it contacts a live source. This may result in injury to the user from electrical shock and/or flash fire. Do not breathe mist or vapor. Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Pregnant or breastfeeding women must not handle this product. Should be handled in closed systems, if possible. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Observe good industrial hygiene practices. Avoid release to the environment. For product usage instructions, please see the product label. Precautions for safe handling Level 2 Aerosol. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50?C/122 ?F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store in a well-ventilated place. Store away from incompatible materials (see Section 10 of the SDS). Conditions for safe storage, including any incompatibilities 8. Exposure controls/personal protection Occupational exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents FormType PEL 2400 mg/m3Acetone (CAS 67-64-1) 1000 ppm PEL 1 mg/m3 Dust and mist.Copper (CAS 7440-50-8) 0.1 mg/m3 Fume. PEL 590 mg/m3Methyl ethyl ketone (CAS 78-93-3) 200 ppm PEL 410 mg/m3Methyl isobutyl ketone (CAS 108-10-1) 100 ppm PEL 1800 mg/m3Propane (CAS 74-98-6) 3 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents FormType 1000 ppm US. OSHA Table Z-2 (29 CFR 1910.1000) ValueComponents Type Ceiling 300 ppmToluene (CAS 108-88-3) TWA 200 ppm US. ACGIH Threshold Limit Values ValueComponents Type STEL 750 ppmAcetone (CAS 67-64-1) TWA 500 ppm STEL 300 ppmMethyl ethyl ketone (CAS 78-93-3) TWA 200 ppm STEL 75 ppmMethyl isobutyl ketone (CAS 108-10-1) TWA 20 ppm STEL 1000 ppmn-Butane (CAS 106-97-8) TWA 20 ppmToluene (CAS 108-88-3) US. NIOSH: Pocket Guide to Chemical Hazards ValueComponents FormType TWA 590 mg/m3Acetone (CAS 67-64-1) 250 ppm TWA 1 mg/m3 Dust and mist.Copper (CAS 7440-50-8) STEL 885 mg/m3Methyl ethyl ketone (CAS 78-93-3) 300 ppm TWA 590 mg/m3 200 ppm STEL 300 mg/m3Methyl isobutyl ketone (CAS 108-10-1) 75 ppm TWA 205 mg/m3 50 ppm TWA 1900 mg/m3n-Butane (CAS 106-97-8) 800 ppm TWA 1800 mg/m3Propane (CAS 74-98-6) 1000 ppm STEL 560 mg/m3Toluene (CAS 108-88-3) 150 ppm TWA 375 mg/m3 100 ppm Biological limit values ACGIH Biological Exposure Indices ValueComponents Determinant Specimen Sampling Time 50 mg/l Acetone Urine *Acetone (CAS 67-64-1) 2 mg/l MEK Urine *Methyl ethyl ketone (CAS 78-93-3) 1 mg/l Methyl isobutyl ketone Urine *Methyl isobutyl ketone (CAS 108-10-1) 0.3 mg/g o-Cresol, with hydrolysis Creatinine in urine *Toluene (CAS 108-88-3) 0.03 mg/l Toluene Urine * 0.02 mg/l Toluene Blood * * - For sampling details, please see the source document. 4 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US Exposure guidelines US - California OELs: Skin designation Toluene (CAS 108-88-3) Can be absorbed through the skin. US - Minnesota Haz Subs: Skin designation applies Toluene (CAS 108-88-3) Skin designation applies. Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency shower must be available when handling this product. Appropriate engineering controls Individual protection measures, such as personal protective equipment Wear safety glasses with side shields (or goggles).Eye/face protection Skin protection Wear protective gloves such as: Neoprene. Nitrile.Hand protection Wear appropriate chemical resistant clothing.Other If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to determine actual employee exposure levels. Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. General hygiene considerations 9. Physical and chemical properties Appearance Liquid.Physical state Aerosol.Form Copper.Color Solvent.Odor Odor threshold Not available. pH Not available. Melting point/freezing point -138.8 ?F (-94.9 ?C) estimated Initial boiling point and boiling range 132.9 ?F (56.1 ?C) estimated Flash point -20.2 ?F (-29 ?C) Pensky-Martens Closed Cup Evaporation rate Fast. Not available.Flammability (solid, gas) Upper/lower flammability or explosive limits Flammability limit - lower (%) 1 % Flammability limit - upper (%) 12.8 % Vapor pressure 13.5 kPa (101.325 mm Hg) Vapor density 1.55 (air = 1) Relative density 0.74 Solubility (water) Not available. Partition coefficient (n-octanol/water) Not available. Auto-ignition temperature 759.2 ?F (404 ?C) estimated Decomposition temperature Not available. Viscosity (kinematic) < 7 mm?/s (104 ?F (40 ?C)) Percent volatile 85.3 % estimated 5 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US 10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability No dangerous reaction known under conditions of normal use.Possibility of hazardous reactions Heat, flames and sparks. Contact with incompatible materials.Conditions to avoid Acids. Strong oxidizing agents. Nitrates. Ammonia. Amines. Isocyanates. Fluorine. Caustics. Chlorine. Incompatible materials Carbon oxides.Hazardous decomposition products 11. Toxicological information Information on likely routes of exposure Inhalation May cause damage to organs through prolonged or repeated exposure by inhalation. May cause drowsiness and dizziness. Headache. Nausea, vomiting. May cause irritation to the respiratory system. Skin contact Causes skin irritation. Eye contact Causes serious eye irritation. Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia. Symptoms related to the physical, chemical and toxicological characteristics Headache. May cause drowsiness and dizziness. Nausea, vomiting. Aspiration may cause pulmonary edema and pneumonitis. Severe eye irritation. Symptoms may include stinging, tearing, redness, swelling, and blurred vision. May cause respiratory irritation. Skin irritation. May cause redness and pain. Information on toxicological effects Acute toxicity May be fatal if swallowed and enters airways. Narcotic effects. May cause respiratory irritation. Test ResultsProduct Species Copper-Coat? Gasket Compound Dermal Acute LD50 Rabbit 14461 mg/kg estimated Inhalation LC50 Rat 3194 mg/l, 4 Hours estimated Oral * Estimates for product may be based on additional component data not shown. LD50 Rat 4314.1 mg/kg Acute Toxicity Estimate Causes skin irritation.Skin corrosion/irritation Causes serious eye irritation.Serious eye damage/eye irritation Respiratory sensitization Not a respiratory sensitizer. This product is not expected to cause skin sensitization.Skin sensitization No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Germ cell mutagenicity Carcinogenicity Suspected of causing cancer. IARC Monographs. Overall Evaluation of Carcinogenicity Methyl isobutyl ketone (CAS 108-10-1) 2B Possibly carcinogenic to humans. Toluene (CAS 108-88-3) 3 Not classifiable as to carcinogenicity to humans. US. National Toxicology Program (NTP) Report on Carcinogens Not available. Suspected of damaging the unborn child.Reproductive toxicity Specific target organ toxicity - single exposure May cause respiratory irritation. May cause drowsiness and dizziness. 6 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US Specific target organ toxicity - repeated exposure May cause damage to organs through prolonged or repeated exposure. Aspiration hazard May be fatal if swallowed and enters airways. If aspirated into lungs during swallowing or vomiting, may cause chemical pneumonia, pulmonary injury or death. Chronic effects May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation may be harmful. Prolonged exposure may cause chronic effects. 12. Ecological information Toxic to aquatic life.Ecotoxicity Product Test ResultsSpecies Copper-Coat? Gasket Compound Aquatic Acute EC50Crustacea 3.475 mg/l, 48 hours estimatedDaphnia LC50Fish 21.5054 mg/l, 96 hours estimatedFish Components Test ResultsSpecies Acetone (CAS 67-64-1) Aquatic EC50Crustacea 10294 - 17704 mg/l, 48 hoursWater flea (Daphnia magna) LC50Fish 4740 - 6330 mg/l, 96 hoursRainbow trout,donaldson trout (Oncorhynchus mykiss) Copper (CAS 7440-50-8) Aquatic Acute EC50Crustacea 0.03 mg/l, 48 hoursWater flea (Daphnia magna) LC50Fish 0.052 mg/l, 96 hoursRainbow trout,donaldson trout (Oncorhynchus mykiss) Methyl ethyl ketone (CAS 78-93-3) Aquatic EC50Crustacea 4025 - 6440 mg/l, 48 hoursWater flea (Daphnia magna) Acute LC50Fish 2993 mg/l, 96 hoursFathead minnow (Pimephales promelas) Methyl isobutyl ketone (CAS 108-10-1) Aquatic LC50Fish 492 - 593 mg/l, 96 hoursFathead minnow (Pimephales promelas) Toluene (CAS 108-88-3) Aquatic EC50Crustacea 5.46 - 9.83 mg/l, 48 hoursWater flea (Daphnia magna) * Estimates for product may be based on additional component data not shown. LC50Fish 8.11 mg/l, 96 hoursCoho salmon,silver salmon (Oncorhynchus kisutch) No data is available on the degradability of this product. Persistence and degradability Bioaccumulative potential Partition coefficient n-octanol / water (log Kow) Acetone -0.24 Methyl ethyl ketone 0.29 Methyl isobutyl ketone 1.31 n-Butane 2.89 Propane 2.36 Toluene 2.73 No data available.Mobility in soil Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 7 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US 13. Disposal considerations If discarded, this product is considered a RCRA ignitable waste, D001. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Contents under pressure. Do not puncture, incinerate or crush. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance with all applicable regulations. Disposal of waste from residues / unused products D001: Waste Flammable material with a flash point <140 FHazardous waste code Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Contaminated packaging 14. Transport information DOT UN1950UN number Aerosols, flammable, Limited QuantityUN proper shipping name 2.1Class Transport hazard class(es) -Subsidiary risk 2.1Label(s) Not applicable.Packing group Read safety instructions, SDS and emergency procedures before handling.Special precautions for user N82Special provisions 306Packaging exceptions 304Packaging non bulk NonePackaging bulk IATA UN1950UN number Aerosols, flammable, Limited QuantityUN proper shipping name 2.1Class Transport hazard class(es) -Subsidiary risk Not applicable.Packing group No.Environmental hazards 10LERG Code Read safety instructions, SDS and emergency procedures before handling.Special precautions for user Allowed.Passenger and cargo aircraft Other information Allowed.Cargo aircraft only IMDG UN1950UN number AEROSOLS, LIMITED QUANTITYUN proper shipping name 2Class Transport hazard class(es) -Subsidiary risk Not applicable.Packing group No.Marine pollutant Environmental hazards F-D, S-UEmS Read safety instructions, SDS and emergency procedures before handling.Special precautions for user 15. Regulatory information This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. US federal regulations TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed. SARA 304 Emergency release notification Not regulated. 8 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Copper (CAS 7440-50-8) Methyl isobutyl ketone (CAS 108-10-1) Toluene (CAS 108-88-3) CERCLA Hazardous Substance List (40 CFR 302.4) Acetone (CAS 67-64-1) Listed. Copper (CAS 7440-50-8) Listed. Methyl ethyl ketone (CAS 78-93-3) Listed. Toluene (CAS 108-88-3) Listed. CERCLA Hazardous Substances: Reportable quantity Acetone (CAS 67-64-1) 5000 LBS Copper (CAS 7440-50-8) 5000 LBS Methyl ethyl ketone (CAS 78-93-3) 5000 LBS Toluene (CAS 108-88-3) 1000 LBS Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Toluene (CAS 108-88-3) Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) n-Butane (CAS 106-97-8) Propane (CAS 74-98-6) Not regulated.Safe Drinking Water Act (SDWA) Drug Enforcement Administration (DEA). List 2, Essential Chemicals (21 CFR 1310.02(b) and 1310.04(f)(2) and Chemical Code Number Acetone (CAS 67-64-1) 6532 Methyl ethyl ketone (CAS 78-93-3) 6714 Methyl isobutyl ketone (CAS 108-10-1) 6715 Toluene (CAS 108-88-3) 6594 Drug Enforcement Administration (DEA). List 1 & 2 Exempt Chemical Mixtures (21 CFR 1310.12(c)) Acetone (CAS 67-64-1) 35 %WV Methyl ethyl ketone (CAS 78-93-3) 35 %WV Methyl isobutyl ketone (CAS 108-10-1) 35 %WV Toluene (CAS 108-88-3) 35 %WV DEA Exempt Chemical Mixtures Code Number Acetone (CAS 67-64-1) 6532 Methyl ethyl ketone (CAS 78-93-3) 6714 Methyl isobutyl ketone (CAS 108-10-1) 6715 Toluene (CAS 108-88-3) 594 Not regulated.Food and Drug Administration (FDA) Superfund Amendments and Reauthorization Act of 1986 (SARA) Immediate Hazard - Yes Delayed Hazard - Yes Fire Hazard - Yes Pressure Hazard - Yes Reactivity Hazard - No Section 311/312 Hazard categories NoSARA 302 Extremely hazardous substance US state regulations US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a)) Acetone (CAS 67-64-1) Copper (CAS 7440-50-8) Methyl ethyl ketone (CAS 78-93-3) n-Butane (CAS 106-97-8) Methyl isobutyl ketone (CAS 108-10-1) Toluene (CAS 108-88-3) US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100) Not listed. 9 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US US. New Jersey Worker and Community Right-to-Know Act Acetone (CAS 67-64-1) Methyl ethyl ketone (CAS 78-93-3) Copper (CAS 7440-50-8) n-Butane (CAS 106-97-8) Propane (CAS 74-98-6) Toluene (CAS 108-88-3) US. Massachusetts RTK - Substance List Acetone (CAS 67-64-1) Copper (CAS 7440-50-8) Methyl ethyl ketone (CAS 78-93-3) n-Butane (CAS 106-97-8) Propane (CAS 74-98-6) Toluene (CAS 108-88-3) US. Pennsylvania Worker and Community Right-to-Know Law Acetone (CAS 67-64-1) Methyl ethyl ketone (CAS 78-93-3) Toluene (CAS 108-88-3) Copper (CAS 7440-50-8) Methyl isobutyl ketone (CAS 108-10-1) n-Butane (CAS 106-97-8) Propane (CAS 74-98-6) US. Rhode Island RTK Acetone (CAS 67-64-1) Copper (CAS 7440-50-8) Methyl ethyl ketone (CAS 78-93-3) n-Butane (CAS 106-97-8) Propane (CAS 74-98-6) Toluene (CAS 108-88-3) US. California Proposition 65 WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. US - California Proposition 65 - CRT: Listed date/Carcinogenic substance Methyl isobutyl ketone (CAS 108-10-1) Listed: November 4, 2011 US - California Proposition 65 - CRT: Listed date/Developmental toxin Methyl isobutyl ketone (CAS 108-10-1) Listed: March 28, 2014 Toluene (CAS 108-88-3) Listed: January 1, 1991 US - California Proposition 65 - CRT: Listed date/Female reproductive toxin Toluene (CAS 108-88-3) Listed: August 7, 2009 Volatile organic compounds (VOC) regulations EPA VOC content (40 CFR 51.100(s)) 54.2 % Not regulatedConsumer products (40 CFR 59, Subpt. C) State This product is regulated as an Automotive Engine Compartment Spray Adhesive. This product is compliant for use in all 50 states. Consumer products VOC content (CA) 54.2 % VOC content (OTC) 54.2 % International Inventories Country(s) or region Inventory name On inventory (yes/no)* YesAustralia Australian Inventory of Chemical Substances (AICS) YesCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) YesChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial Chemical Substances (EINECS) 10 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US Country(s) or region Inventory name On inventory (yes/no)* NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) YesKorea Existing Chemicals List (ECL) YesNew Zealand New Zealand Inventory YesPhilippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision 07-16-2015Issue date Allison ChoPrepared by Version # 01 Not available.Further information Health: 2* Flammability: 4 Physical hazard: 0 Personal protection: B HMIS? ratings Health: 2 Flammability: 4 Instability: 0 NFPA ratings NFPA ratings 02 4 The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. This information is accurate to the best of CRC Industries' knowledge or obtained from sources believed by CRC to be accurate. Before using any product, read all warnings and directions on the label. For further clarification of any information contained on this (M)SDS consult your supervisor, a health & safety professional, or CRC Industries. Disclaimer 11 / 11 Material name: Copper-Coat? Gasket Compound 401612 Version #: 01 Issue date: 07-16-2015 SDS US