SAFETY DATA SHEET 1. Identification Fuel Injector and Carburetor CleanerProduct identifier Other means of identification 05061 (Item #1003675)Product code Pour-in fuel additiveRecommended use None known.Recommended restrictions Manufacturer/Importer/Supplier/Distributor information Manufactured or sold by: CRC Industries, Inc.Company name 885 Louis Dr.Address Warminster, PA 18974 US Telephone 215-674-4300General Information 800-521-3168Technical Assistance 800-272-4620Customer Service 800-424-9300 (US)24-Hour Emergency 703-527-3887 (International)(CHEMTREC) www.crcindustries.comWebsite 2. Hazard(s) identification Category 4Flammable liquidsPhysical hazards Category 4Acute toxicity, inhalationHealth hazards Category 2Skin corrosion/irritation Category 2Germ cell mutagenicity Category 2Carcinogenicity Category 1Aspiration hazard Category 2Hazardous to the aquatic environment, acute hazard Environmental hazards Category 2Hazardous to the aquatic environment, long-term hazard Not classified.OSHA defined hazards Label elements Signal word Danger Hazard statement Combustible liquid. May be fatal if swallowed and enters airways. Causes skin irritation. Harmful if inhaled. Suspected of causing genetic defects. Suspected of causing cancer. Toxic to aquatic life with long lasting effects. Precautionary statement Prevention Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from flames and hot surfaces-No smoking. Use with adequate ventilation. Open doors and windows or use other means to ensure a fresh air supply during use and while product is drying. If you experience any symptoms listed on this label, increase ventilation or leave the area. Avoid breathing vapors. Wash thoroughly after handling. Wear protective gloves/protective clothing/eye protection/face protection. Avoid release to the environment. 1 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Wash with plenty of water. If inhaled: Remove person to fresh air and keep comfortable for breathing. If exposed or concerned: Get medical advice/attention. Call a poison center/doctor if you feel unwell. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash before reuse. In case of fire: Use appropriate media to extinguish. Collect spillage. Storage Store in a well-ventilated place. Keep cool. Store locked up. Disposal Dispose of contents/container in accordance with local/regional/national regulations. Hazard(s) not otherwise classified (HNOC) None known. 3. Composition/information on ingredients Mixtures CAS number %Chemical name Common name and synonyms Diesel Fuel No. 2 64742-80-9distillates (petroleum), hydrodesulfurized middle 90 - 100 64742-47-8distillates (petroleum), hydrotreated light < 1 64742-46-7distillates (petroleum), hydrotreated middle < 0.2 Specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing. Oxygen or artificial respiration if needed. Call a POISON CENTER or doctor/physician if you feel unwell. Inhalation Remove contaminated clothing. Rinse skin with water/shower. If skin irritation occurs: Get medical advice/attention. Wash contaminated clothing before reuse. Skin contact Rinse with water. Get medical attention if irritation develops and persists.Eye contact Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. Ingestion Aspiration may cause pulmonary edema and pneumonitis. Dizziness. Direct contact with eyes may cause temporary irritation. Skin irritation. May cause redness and pain. Most important symptoms/effects, acute and delayed Provide general supportive measures and treat symptomatically. Keep victim warm. Keep victim under observation. Symptoms may be delayed. Indication of immediate medical attention and special treatment needed IF exposed or concerned: Get medical advice/attention. Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Show this safety data sheet to the doctor in attendance. General information 5. Fire-fighting measures Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing media The product is combustible, and heating may generate vapors which may form explosive vapor/air mixtures. During fire, gases hazardous to health may be formed. Specific hazards arising from the chemical Self-contained breathing apparatus and full protective clothing must be worn in case of fire.Special protective equipment and precautions for firefighters Fire-fighting equipment/instructions In case of fire and/or explosion do not breathe fumes. Move containers from fire area if you can do so without risk. Combustible liquid.General fire hazards 6. Accidental release measures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Wear appropriate protective equipment and clothing during clean-up. Avoid inhalation of vapors and spray mists. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ensure adequate ventilation. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Personal precautions, protective equipment and emergency procedures 2 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. This product is miscible in water. Prevent product from entering drains. Small Spills: Absorb with earth, sand or other non-combustible material and transfer to containers for later disposal. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. Never return spills to original containers for re-use. Put material in suitable, covered, labeled containers. For waste disposal, see section 13 of the SDS. Methods and materials for containment and cleaning up Avoid release to the environment. Inform appropriate managerial or supervisory personnel of all environmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge into drains, water courses or onto the ground. Environmental precautions 7. Handling and storage Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Keep away from open flames, hot surfaces and sources of ignition. When using do not smoke. Avoid inhalation of vapors and spray mists. Avoid contact with eyes, skin, and clothing. Avoid prolonged exposure. Should be handled in closed systems, if possible. Use only outdoors or in a well-ventilated area. Wear appropriate personal protective equipment. Wash hands thoroughly after handling. Avoid release to the environment. Observe good industrial hygiene practices. For product usage instructions, see the product label. Precautions for safe handling Keep away from heat, sparks and open flame. Store in a cool, dry place out of direct sunlight. Keep container tightly closed. Store in a well-ventilated place. Keep in an area equipped with sprinklers. Store away from incompatible materials (see Section 10 of the SDS). Conditions for safe storage, including any incompatibilities 8. Exposure controls/personal protection Occupational exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents FormType PEL 400 mg/m3distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) 100 ppm PEL 400 mg/m3distillates (petroleum), hydrotreated light (CAS 64742-47-8) 100 ppm PEL 5 mg/m3 Mist.distillates (petroleum), hydrotreated middle (CAS 64742-46-7) 400 mg/m3 100 ppm US. ACGIH Threshold Limit Values ValueComponents FormType TWA 5 mg/m3 Inhalable fraction.distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) TWA 5 mg/m3 Inhalable fraction.distillates (petroleum), hydrotreated middle (CAS 64742-46-7) US. NIOSH: Pocket Guide to Chemical Hazards ValueComponents FormType TWA 400 mg/m3distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) 100 ppm TWA 100 mg/m3distillates (petroleum), hydrotreated light (CAS 64742-47-8) STEL 10 mg/m3 Mist.distillates (petroleum), hydrotreated middle (CAS 64742-46-7) TWA 5 mg/m3 Mist. 3 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US No biological exposure limits noted for the ingredient(s).Biological limit values Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Eye wash facilities and emergency shower should be available when handling this product. Appropriate engineering controls Individual protection measures, such as personal protective equipment Wear safety glasses with side shields (or goggles).Eye/face protection Skin protection Wear protective gloves such as: Nitrile. Neoprene. Polyvinyl chloride (PVC).Hand protection Wear appropriate chemical resistant clothing.Other If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to determine actual employee exposure levels. Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. General hygiene considerations 9. Physical and chemical properties Appearance Liquid.Physical state Liquid.Form Light amber.Color Petroleum.Odor Odor threshold Not available. pH Not available. Melting point/freezing point Not available. Initial boiling point and boiling range 320 ?F (160 ?C) estimated Flash point 165 ?F (73.9 ?C) Tag Closed Cup Evaporation rate Slow. Not available.Flammability (solid, gas) Upper/lower flammability or explosive limits Flammability limit - lower (%) 0.5 % estimated Flammability limit - upper (%) 7.5 % estimated Vapor pressure 0.6 hPa estimated Vapor density > 1 (air = 1) Relative density 0.84 Solubility (water) Negligible. Partition coefficient (n-octanol/water) Not available. Auto-ignition temperature 494 ?F (256.7 ?C) estimated Decomposition temperature Not available. Viscosity (kinematic) Not available. Percent volatile 99.3 % estimated 10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability 4 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US No dangerous reaction known under conditions of normal use.Possibility of hazardous reactions Avoid heat, sparks, open flames and other ignition sources. Avoid temperatures exceeding the flash point. Contact with incompatible materials. Conditions to avoid Strong oxidizing agents.Incompatible materials Carbon oxides. Hydrocarbon fumes and smoke.Hazardous decomposition products 11. Toxicological information Information on likely routes of exposure Inhalation Harmful if inhaled. Skin contact Causes skin irritation. Eye contact Direct contact with eyes may cause temporary irritation. Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a serious chemical pneumonia. Symptoms related to the physical, chemical and toxicological characteristics Aspiration may cause pulmonary edema and pneumonitis. Dizziness. Skin irritation. May cause redness and pain. Information on toxicological effects Acute toxicity May be fatal if swallowed and enters airways. Harmful if inhaled. Test ResultsComponents Species distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) Dermal Acute LD50 Rabbit > 2000 mg/kg Inhalation LC50 Rat 10 - 20 mg/l, 4 hours Vapor distillates (petroleum), hydrotreated light (CAS 64742-47-8) Dermal Acute * Estimates for product may be based on additional component data not shown. LD50 Rat > 2000 mg/kg Causes skin irritation.Skin corrosion/irritation Direct contact with eyes may cause temporary irritation.Serious eye damage/eye irritation Respiratory sensitization Not a respiratory sensitizer. This product is not expected to cause skin sensitization.Skin sensitization Suspected of causing genetic defects.Germ cell mutagenicity Carcinogenicity Suspected of causing cancer. IARC Monographs. Overall Evaluation of Carcinogenicity Not listed. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not regulated. US. National Toxicology Program (NTP) Report on Carcinogens Not listed. This product is not expected to cause reproductive or developmental effects.Reproductive toxicity Specific target organ toxicity - single exposure Not classified. Specific target organ toxicity - repeated exposure Not classified. Aspiration hazard May be fatal if swallowed and enters airways. If aspirated into lungs during swallowing or vomiting, may cause chemical pneumonia, pulmonary injury or death. 5 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US Chronic effects Prolonged inhalation may be harmful. 12. Ecological information Toxic to aquatic life with long lasting effects.Ecotoxicity Components Test ResultsSpecies distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) Aquatic EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex) LC50Fish 8.8 mg/l, 96 hoursRainbow trout,donaldson trout (Oncorhynchus mykiss) 8.8 mg/l, 96 hours distillates (petroleum), hydrotreated light (CAS 64742-47-8) Aquatic Acute EC50Crustacea 1.1 mg/l, 48 hoursWater flea (Daphnia magna) LC50Fish 3 mg/l, 96 hoursFathead minnow (Pimephales promelas) distillates (petroleum), hydrotreated middle (CAS 64742-46-7) Aquatic EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex) LC50Fish 8.8 mg/l, 96 hoursRainbow trout,donaldson trout (Oncorhynchus mykiss) * Estimates for product may be based on additional component data not shown. 8.8 mg/l, 96 hours Persistence and degradability Bioaccumulative potential No data available.Mobility in soil Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 13. Disposal considerations This product is not a RCRA hazardous waste (See 40 CFR Part 261.20 ? 261.33). Empty containers may be recycled. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance with all applicable regulations. Disposal of waste from residues / unused products Not regulated.Hazardous waste code Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Contaminated packaging 14. Transport information DOT Not regulated as dangerous goods. IATA Not regulated as dangerous goods. IMDG Not regulated as dangerous goods. 15. Regulatory information This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. US federal regulations TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. SARA 304 Emergency release notification Not regulated. 6 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not regulated. US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Not listed. CERCLA Hazardous Substance List (40 CFR 302.4) Not listed. CERCLA Hazardous Substances: Reportable quantity Not listed. Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Not regulated. Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Not regulated. Not regulated.Safe Drinking Water Act (SDWA) Not regulated.Food and Drug Administration (FDA) Superfund Amendments and Reauthorization Act of 1986 (SARA) Immediate Hazard - Yes Delayed Hazard - Yes Fire Hazard - Yes Pressure Hazard - No Reactivity Hazard - No Section 311/312 Hazard categories NoSARA 302 Extremely hazardous substance US state regulations US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a)) distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) distillates (petroleum), hydrotreated middle (CAS 64742-46-7) US. New Jersey Worker and Community Right-to-Know Act distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) US. Massachusetts RTK - Substance List distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) US. Pennsylvania Worker and Community Right-to-Know Law distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) distillates (petroleum), hydrotreated light (CAS 64742-47-8) distillates (petroleum), hydrotreated middle (CAS 64742-46-7) US. Rhode Island RTK distillates (petroleum), hydrodesulfurized middle (CAS 64742-80-9) US. California Proposition 65 WARNING: This product contains a chemical known to the State of California to cause cancer and birth defects or other reproductive harm. US - California Proposition 65 - CRT: Listed date/Carcinogenic substance benzene (CAS 71-43-2) Listed: February 27, 1987 naphthalene (CAS 91-20-3) Listed: April 19, 2002 US - California Proposition 65 - CRT: Listed date/Developmental toxin benzene (CAS 71-43-2) Listed: December 26, 1997 US - California Proposition 65 - CRT: Listed date/Male reproductive toxin benzene (CAS 71-43-2) Listed: December 26, 1997 Volatile organic compounds (VOC) regulations EPA VOC content (40 CFR 51.100(s)) 99 % Not regulatedConsumer products (40 CFR 59, Subpt. C) 7 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US State Not regulatedConsumer products VOC content (CA) 99 % VOC content (OTC) 99 % International Inventories Country(s) or region Inventory name On inventory (yes/no)* YesAustralia Australian Inventory of Chemical Substances (AICS) NoCanada Domestic Substances List (DSL) YesCanada Non-Domestic Substances List (NDSL) YesChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial Chemical Substances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) YesKorea Existing Chemicals List (ECL) YesNew Zealand New Zealand Inventory YesPhilippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision 05-11-2015Issue date 06-29-2017Revision date Allison YoonPrepared by Version # 02 CRC # 635F/1002670Further information Health: 2* Flammability: 2 Physical hazard: 0 Personal protection: B HMIS? ratings Health: 2 Flammability: 2 Instability: 0 NFPA ratings NFPA ratings 02 2 The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. This information is accurate to the best of CRC's knowledge or obtained from sources believed by CRC to be accurate. Before using any product, read all warnings and directions on the label. For further clarification of any information contained on this (M)SDS consult your supervisor, a health & safety professional, or CRC Industries, Inc.. Disclaimer This document has undergone significant changes and should be reviewed in its entirety.Revision Information 8 / 8 Material name: Fuel Injector and Carburetor Cleaner 05061 (Item #1003675) Version #: 02 Revision date: 06-29-2017 Issue date: 05-11-2015 SDS US