SAFETY DATA SHEET 1. Identification Cutting Oil Thread Cutting LubricantProduct identifier Other means of identification 14050Product code Cutting oilRecommended use None known.Recommended restrictions Manufacturer/Importer/Supplier/Distributor information Manufactured or sold by: Company name CRC Industries, Inc. Address 885 Louis Dr. Warminster, PA 18974 US Telephone General Information 215-674-4300 Technical Assistance 800-521-3168 Customer Service 800-272-4620 24-Hour Emergency 800-424-9300 (US) (CHEMTREC) 703-527-3887 (International) Website www.crcindustries.com 2. Hazard(s) identification Category 1Flammable aerosolsPhysical hazards Liquefied gasGases under pressure Not classified.Health hazards Not classified.Environmental hazards Not classified.OSHA defined hazards Label elements Signal word Danger Hazard statement Extremely flammable aerosol. Contains gas under pressure; may explode if heated. Precautionary statement Prevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an open flame or other ignition source. Do not apply while equipment is energized. Pressurized container: Do not pierce or burn, even after use. Extinguish all flames, pilot lights and heaters. Vapors will accumulate readily and may ignite. Use only with adequate ventilation; maintain ventilation during use and until all vapors are gone. Open doors and windows or use other means to ensure a fresh air supply during use and while product is drying. If you experience any symptoms listed on this label, increase ventilation or leave the area. Response Wash hands after handling. Storage Store in a well-ventilated place. Protect from sunlight. Do not expose to temperatures exceeding 50?C/122?F. Exposure to high temperature may cause can to burst. Disposal Dispose of contents/container in accordance with local/regional/national regulations. Hazard(s) not otherwise classified (HNOC) None known. 3. Composition/information on ingredients Mixtures 1 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US CAS number %Common name and synonymsChemical name 64742-52-5Distillates (petroleum), hydrotreated heavy naphthenic 70 - 80 68476-86-8Liquefied Petroleum Gas 20 - 30 Specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Move to fresh air. Call a physician if symptoms develop or persist.Inhalation Rinse skin with water/shower. Get medical attention if irritation develops and persists.Skin contact Rinse with water. Get medical attention if irritation develops and persists.Eye contact If swallowed, observe for signs of stomach discomfort or nausea. If symptoms persist, seek medical help. Do not induce vomiting. If there is any suspicion of aspiration into lungs, obtain immediate medical attention. Ingestion Direct contact with eyes may cause temporary irritation.Most important symptoms/effects, acute and delayed Provide general supportive measures and treat symptomatically.Indication of immediate medical attention and special treatment needed Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. General information 5. Fire-fighting measures Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishing media Contents under pressure. Pressurized container may rupture when exposed to heat or flame. During fire, gases hazardous to health may be formed. Specific hazards arising from the chemical Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. Special protective equipment and precautions for firefighters Fire-fighting equipment/instructions In case of fire: Stop leak if safe to do so. Move containers from fire area if you can do so without risk. Containers should be cooled with water to prevent vapor pressure build up. Extremely flammable aerosol. Contents under pressure. Pressurized container may rupture when exposed to heat or flame. General fire hazards 6. Accidental release measures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Many vapors are heavier than air and will spread along ground and collect in low or confined areas (sewers, basements, tanks). Wear appropriate protective equipment and clothing during clean-up. Emergency personnel need self-contained breathing equipment. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. Ventilate closed spaces before entering them. Local authorities should be advised if significant spillages cannot be contained. For personal protection, see section 8 of the SDS. Personal precautions, protective equipment and emergency procedures Eliminate all ignition sources (no smoking, flares, sparks, or flames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material. Stop the flow of material, if this is without risk. Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. For waste disposal, see section 13 of the SDS. Methods and materials for containment and cleaning up Avoid discharge into drains, water courses or onto the ground.Environmental precautions 7. Handling and storage Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missing or defective. Do not spray on a naked flame or any other incandescent material. Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers to heat, flame, sparks, or other sources of ignition. Use caution around energized equipment. The metal container will conduct electricity if it contacts a live source. This may result in injury to the user from electrical shock and/or flash fire. Use only in well-ventilated areas. Wear appropriate personal protective equipment. Observe good industrial hygiene practices. For product usage instructions, please see the product label. Precautions for safe handling 2 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US Level 3 Aerosol. Pressurized container. Protect from sunlight and do not expose to temperatures exceeding 50?C/122 ?F. Do not puncture, incinerate or crush. Do not handle or store near an open flame, heat or other sources of ignition. This material can accumulate static charge which may cause spark and become an ignition source. Store in a well-ventilated place. Store away from incompatible materials (see Section 10 of the SDS). Conditions for safe storage, including any incompatibilities 8. Exposure controls/personal protection Occupational exposure limits US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents FormType PEL 5 mg/m3 Mist.Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) 2000 mg/m3 500 ppm US. ACGIH Threshold Limit Values ValueComponents FormType TWA 5 mg/m3 Inhalable fraction.Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) US. NIOSH: Pocket Guide to Chemical Hazards ValueComponents FormType Ceiling 1800 mg/m3Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) STEL 10 mg/m3 Mist. No biological exposure limits noted for the ingredient(s).Biological limit values Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Appropriate engineering controls Individual protection measures, such as personal protective equipment Wear safety glasses with side shields (or goggles).Eye/face protection Skin protection Wear protective gloves such as: Nitrile. Neoprene.Hand protection Wear suitable protective clothing.Other If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to determine actual employee exposure levels. Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards When using do not smoke. Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. General hygiene considerations 9. Physical and chemical properties Appearance Liquid.Physical state Aerosol.Form Brown.Color Mild petroleum.Odor Odor threshold Not available. pH Not available. 3 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US Melting point/freezing point -40 ?F (-40 ?C) estimated Initial boiling point and boiling range 500 ?F (260 ?C) estimated Flash point > 300 ?F (> 148.9 ?C) Cleveland Open Cup Evaporation rate Slow. Not available.Flammability (solid, gas) Upper/lower flammability or explosive limits Flammability limit - lower (%) Not available. Flammability limit - upper (%) Not available. Vapor pressure 965.3 hPa estimated Vapor density > 5 (air = 1) Relative density 0.85 Solubility (water) Negligible. Partition coefficient (n-octanol/water) Not available. Auto-ignition temperature 600 ?F (315.6 ?C) estimated Decomposition temperature Not available. Viscosity (kinematic) Not available. Percent volatile 94.4 % estimated 10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability No dangerous reaction known under conditions of normal use.Possibility of hazardous reactions Heat, flames and sparks. Contact with incompatible materials.Conditions to avoid Strong oxidizing agents.Incompatible materials Carbon oxides. Sulfur oxides. Aldehydes.Hazardous decomposition products 11. Toxicological information Information on likely routes of exposure Inhalation Prolonged inhalation may be harmful. Skin contact Prolonged skin contact may cause temporary irritation. Eye contact Direct contact with eyes may cause temporary irritation. Ingestion Expected to be a low ingestion hazard. Symptoms related to the physical, chemical and toxicological characteristics Direct contact with eyes may cause temporary irritation. Information on toxicological effects Acute toxicity Not available. Test ResultsProduct Species Cutting Oil Thread Cutting Lubricant Dermal Acute LD50 Rabbit 2841 mg/kg estimated Inhalation LC50 Rat 30 mg/l, 4 hours estimated 4 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US Test ResultsProduct Species Oral * Estimates for product may be based on additional component data not shown. LD50 Rat 5924 mg/kg estimated Prolonged skin contact may cause temporary irritation.Skin corrosion/irritation Direct contact with eyes may cause temporary irritation.Serious eye damage/eye irritation Respiratory sensitization Not a respiratory sensitizer. This product is not expected to cause skin sensitization.Skin sensitization No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Germ cell mutagenicity Carcinogenicity This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. This product is not expected to cause reproductive or developmental effects.Reproductive toxicity Specific target organ toxicity - single exposure Not classified. Specific target organ toxicity - repeated exposure Not classified. Aspiration hazard Not expected to be an aspiration hazard. 12. Ecological information The product is not classified as environmentally hazardous. However, this does not exclude the possibility that large or frequent spills can have a harmful or damaging effect on the environment. Ecotoxicity Product Test ResultsSpecies Cutting Oil Thread Cutting Lubricant Aquatic Acute EC50Crustacea 25000 mg/l, 48 hours estimatedDaphnia LC50Fish 16094.4199 mg/l, 96 hours estimatedFish Components Test ResultsSpecies * Estimates for product may be based on additional component data not shown. Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) Aquatic Acute LC50Fish > 30000 mg/l, 96 hoursPimephales promelas No data is available on the degradability of this product. Persistence and degradability No data available.Bioaccumulative potential No data available.Mobility in soil Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 13. Disposal considerations The dispensed liquid product is not a RCRA hazardous waste (See 40 CFR Part 261.20 - 261.33). Empty container can be recycled. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Dispose in accordance with all applicable regulations. Disposal of waste from residues / unused products Not regulated.Hazardous waste code Since emptied containers may retain product residue, follow label warnings even after container is emptied. Empty containers should be taken to an approved waste handling site for recycling or disposal. Contaminated packaging 14. Transport information DOT UN1950UN number Aerosols, flammable, Limited QuantityUN proper shipping name 5 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US 2.1Class Transport hazard class(es) -Subsidiary risk 2.1Label(s) Not applicable.Packing group Read safety instructions, SDS and emergency procedures before handling.Special precautions for user N82Special provisions 306Packaging exceptions NonePackaging non bulk NonePackaging bulk IATA UN1950UN number Aerosols, flammable, Limited QuantityUN proper shipping name 2.1Class Transport hazard class(es) -Subsidiary risk Not applicable.Packing group No.Environmental hazards 10LERG Code Read safety instructions, SDS and emergency procedures before handling.Special precautions for user Allowed.Passenger and cargo aircraft Other information Allowed.Cargo aircraft only IMDG UN1950UN number AEROSOLS, LIMITED QUANTITYUN proper shipping name 2Class Transport hazard class(es) -Subsidiary risk Not applicable.Packing group No.Marine pollutant Environmental hazards F-D, S-UEmS Read safety instructions, SDS and emergency procedures before handling.Special precautions for user 15. Regulatory information This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. US federal regulations TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed. SARA 304 Emergency release notification Not regulated. US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Not listed. CERCLA Hazardous Substance List (40 CFR 302.4) Not listed. CERCLA Hazardous Substances: Reportable quantity Not listed. Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Not regulated. Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Not regulated. 6 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US Not regulated.Safe Drinking Water Act (SDWA) Not regulated.Food and Drug Administration (FDA) Superfund Amendments and Reauthorization Act of 1986 (SARA) Immediate Hazard - No Delayed Hazard - No Fire Hazard - Yes Pressure Hazard - Yes Reactivity Hazard - No Section 311/312 Hazard categories NoSARA 302 Extremely hazardous substance US state regulations US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a)) Liquefied Petroleum Gas (CAS 68476-86-8) Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100) Not listed. US. New Jersey Worker and Community Right-to-Know Act Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) US. Massachusetts RTK - Substance List Distillates (petroleum), hydrotreated heavy naphthenic (CAS 64742-52-5) US. Pennsylvania Worker and Community Right-to-Know Law Not listed. US. Rhode Island RTK None. US. California Proposition 65 California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. Volatile organic compounds (VOC) regulations EPA VOC content (40 CFR 51.100(s)) 100 % Not regulatedConsumer products (40 CFR 59, Subpt. C) State This product is regulated as a Cutting or Tapping Oil (aerosol). This product is compliant for use in all 50 states. Local restriction: This product cannot be used in the South Coast Air Quality Management District of California. Consumer products VOC content (CA) 20 % VOC content (OTC) 20 % International Inventories Country(s) or region Inventory name On inventory (yes/no)* YesAustralia Australian Inventory of Chemical Substances (AICS) YesCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) YesChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial Chemical Substances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) YesKorea Existing Chemicals List (ECL) YesNew Zealand New Zealand Inventory YesPhilippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) 7 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US Country(s) or region Inventory name On inventory (yes/no)* YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision 04-28-2015Issue date 05-21-2015Revision date Allison ChoPrepared by Version # 02 CRC # 574Further information Health: 1 Flammability: 3 Physical hazard: 0 Personal protection: B HMIS? ratings Health: 1 Flammability: 3 Instability: 0 NFPA ratings NFPA ratings 01 3 The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. This information is accurate to the best of CRC Industries' knowledge or obtained from sources believed by CRC to be accurate. Before using any product, read all warnings and directions on the label. For further clarification of any information contained on this (M)SDS consult your supervisor, a health & safety professional, or CRC Industries. Disclaimer 8 / 8 Material name: Cutting Oil Thread Cutting Lubricant 14050 Version #: 02 Revision date: 05-21-2015 Issue date: 04-28-2015 SDS US