3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 1 of 12 Safety Data Sheet Copyright,2018,3M Company. All rights reserved. Copying and/or downloading of this information for the purpose of properly utilizing 3M products is allowed provided that: (1) the information is copied in full with no changes unless prior written agreement is obtained from 3M, and (2) neither the copy nor the original is resold or otherwise distributed with the intention of earning a profit thereon. Document Group: 31-7612-0 Version Number: 2.01 Issue Date: 05/24/18 Supercedes Date: 04/29/14 SECTION 1: Identification 1.1. Product identifier 3M? Super Silicone Sealant (Black), 08662, 08664 Product Identification Numbers 60-4550-7161-7, 60-4550-7163-3 1.2. Recommended use and restrictions on use Recommended use Automotive, General purpose bonding and sealing, as well as formed-in-place gasket applications. 1.3. Supplier?s details MANUFACTURER: 3M DIVISION: Automotive Aftermarket ADDRESS: 3M Center, St. Paul, MN 55144-1000, USA Telephone: 1-888-3M HELPS (1-888-364-3577) 1.4. Emergency telephone number 1-800-364-3577 or (651) 737-6501 (24 hours) SECTION 2: Hazard identification The label elements below were prepared in accordance with OSHA Hazard Communication Standard, 29 CFR 1910.1200. This information may be different from the actual product label information for labels regulated by other agencies. 2.1. Hazard classification Serious Eye Damage/Irritation: Category 2A. Skin Corrosion/Irritation: Category 2. Reproductive Toxicity: Category 2. Carcinogenicity: Category 2. 2.2. Label elements Signal word Warning Symbols 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 2 of 12 Exclamation mark | Health Hazard | Pictograms Hazard Statements Causes serious eye irritation. Causes skin irritation. Suspected of damaging fertility or the unborn child. Suspected of causing cancer. Precautionary Statements General: Keep out of reach of children. Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Wear protective gloves and eye/face protection. Wash thoroughly after handling. Response: IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention. IF ON SKIN: Wash with plenty of soap and water. If skin irritation occurs: Get medical advice/attention. Take off contaminated clothing and wash it before reuse. IF exposed or concerned: Get medical advice/attention. Storage: Store locked up. Disposal: Dispose of contents/container in accordance with applicable local/regional/national/international regulations. 1% of the mixture consists of ingredients of unknown acute oral toxicity. 11% of the mixture consists of ingredients of unknown acute dermal toxicity. 73% of the mixture consists of ingredients of unknown acute inhalation toxicity. SECTION 3: Composition/information on ingredients Ingredient C.A.S. No. % by Wt Siloxanes and Silicones, Di-me, Hydroxy-terminated 70131-67-8 60 - 100 Trade Secret * Poly(Dimethylsiloxane) 63148-62-9 5 - 10 Trade Secret * Silica 7631-86-9 5 - 10 Trade Secret * Solvent Refined Hydrotreated Middle Distillate 64742-46-7 5 - 10 Trade Secret * Ethyltriacetoxysilane 17689-77-9 1 - 5 Trade Secret * Methyltriacetoxysilane 4253-34-3 1 - 5 Trade Secret * Decamethylcyclopentasiloxane 541-02-6 <= 1 Trade Secret * 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 3 of 12 Octamethylcyclotetrasiloxane 556-67-2 <= 1 Trade Secret * Polydimethylcyclosiloxane 69430-24-6 <= 1 Trade Secret * Carbon Black 1333-86-4 <= 0.3 Trade Secret * *The specific chemical identity and/or exact percentage (concentration) of this composition has been withheld as a trade secret. SECTION 4: First aid measures 4.1. Description of first aid measures Inhalation: Remove person to fresh air. If you feel unwell, get medical attention. Skin Contact: Immediately wash with soap and water. Remove contaminated clothing and wash before reuse. If signs/symptoms develop, get medical attention. Eye Contact: Immediately flush with large amounts of water. Remove contact lenses if easy to do. Continue rinsing. Get medical attention. If Swallowed: Rinse mouth. If you feel unwell, get medical attention. 4.2. Most important symptoms and effects, both acute and delayed See Section 11.1. Information on toxicological effects. 4.3. Indication of any immediate medical attention and special treatment required Not applicable SECTION 5: Fire-fighting measures 5.1. Suitable extinguishing media In case of fire: Use a fire fighting agent suitable for ordinary combustible material such as water or foam to extinguish. 5.2. Special hazards arising from the substance or mixture None inherent in this product. Hazardous Decomposition or By-Products Substance Condition Carbon monoxide During Combustion Carbon dioxide During Combustion 5.3. Special protective actions for fire-fighters No special protective actions for fire-fighters are anticipated. SECTION 6: Accidental release measures 6.1. Personal precautions, protective equipment and emergency procedures Evacuate area. Ventilate the area with fresh air. Refer to other sections of this SDS for information regarding physical and health hazards, respiratory protection, ventilation, and personal protective equipment. 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 4 of 12 6.2. Environmental precautions Avoid release to the environment. For larger spills, cover drains and build dikes to prevent entry into sewer systems or bodies of water. 6.3. Methods and material for containment and cleaning up Contain spill. Working from around the edges of the spill inward, cover with bentonite, vermiculite, or commercially available inorganic absorbent material. Mix in sufficient absorbent until it appears dry. Remember, adding an absorbent material does not remove a physical, health, or environmental hazard. Collect as much of the spilled material as possible. Place in a closed container approved for transportation by appropriate authorities. Seal the container. Dispose of collected material as soon as possible in accordance with applicable local/regional/national/international regulations. SECTION 7: Handling and storage 7.1. Precautions for safe handling Keep out of reach of children. Do not handle until all safety precautions have been read and understood. Avoid breathing dust/fume/gas/mist/vapors/spray. Do not get in eyes, on skin, or on clothing. Do not eat, drink or smoke when using this product. Wash thoroughly after handling. Avoid release to the environment. Avoid contact with oxidizing agents (eg. chlorine, chromic acid etc.) Use personal protective equipment (gloves, respirators, etc.) as required. 7.2. Conditions for safe storage including any incompatibilities Store away from oxidizing agents. SECTION 8: Exposure controls/personal protection 8.1. Control parameters Occupational exposure limits If a component is disclosed in section 3 but does not appear in the table below, an occupational exposure limit is not available for the component. Ingredient C.A.S. No. Agency Limit type Additional Comments Carbon Black 1333-86-4 ACGIH TWA(inhalable fraction):3 mg/m3 A3: Confirmed animal carcin. Carbon Black 1333-86-4 OSHA TWA:3.5 mg/m3 Decamethylcyclopentasiloxane 541-02-6 AIHA TWA:10 ppm Octamethylcyclotetrasiloxane 556-67-2 AIHA TWA:10 ppm Paraffin oil 64742-46-7 OSHA TWA(as mist):5 mg/m3 SILICA, AMORPHOUS 7631-86-9 OSHA TWA concentration:0.8 mg/m3;TWA:20 millions of particles/cu. ft. ACGIH : American Conference of Governmental Industrial Hygienists AIHA : American Industrial Hygiene Association CMRG : Chemical Manufacturer's Recommended Guidelines OSHA : United States Department of Labor - Occupational Safety and Health Administration TWA: Time-Weighted-Average STEL: Short Term Exposure Limit CEIL: Ceiling 8.2. Exposure controls 8.2.1. Engineering controls Use general dilution ventilation and/or local exhaust ventilation to control airborne exposures to below relevant Exposure Limits and/or control dust/fume/gas/mist/vapors/spray. If ventilation is not adequate, use respiratory protection equipment. Provide ventilated enclosure for heat curing. Curing enclosures must be exhausted to outdoors or to a suitable emission control device. 8.2.2. Personal protective equipment (PPE) 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 5 of 12 Eye/face protection Select and use eye/face protection to prevent contact based on the results of an exposure assessment. The following eye/face protection(s) are recommended: Indirect Vented Goggles Skin/hand protection Select and use gloves and/or protective clothing approved to relevant local standards to prevent skin contact based on the results of an exposure assessment. Selection should be based on use factors such as exposure levels, concentration of the substance or mixture, frequency and duration, physical challenges such as temperature extremes, and other use conditions. Consult with your glove and/or protective clothing manufacturer for selection of appropriate compatible gloves/protective clothing. Gloves made from the following material(s) are recommended: Neoprene Polymer laminate Respiratory protection An exposure assessment may be needed to decide if a respirator is required. If a respirator is needed, use respirators as part of a full respiratory protection program. Based on the results of the exposure assessment, select from the following respirator type(s) to reduce inhalation exposure: Half facepiece or full facepiece air-purifying respirator suitable for organic vapors and particulates For questions about suitability for a specific application, consult with your respirator manufacturer. SECTION 9: Physical and chemical properties 9.1. Information on basic physical and chemical properties General Physical Form: Liquid Odor, Color, Grade: Black silicone elastomer paste with acetic acid odor. Odor threshold No Data Available pH No Data Available Melting point No Data Available Boiling Point No Data Available Flash Point >=212 ?C [Test Method:Closed Cup] Flash Point Flash point > 93 ?C (200 ?F) [Test Method:Closed Cup] Evaporation rate No Data Available Flammability (solid, gas) Not Applicable Flammable Limits(LEL) No Data Available Flammable Limits(LEL) No Data Available Flammable Limits(UEL) No Data Available Vapor Pressure No Data Available Vapor Density No Data Available Density 1.0 g/ml Specific Gravity 1.0 [Ref Std:WATER=1] Solubility In Water No Data Available Solubility- non-water No Data Available Solubility- non-water No Data Available Partition coefficient: n-octanol/ water No Data Available Autoignition temperature No Data Available Decomposition temperature No Data Available Viscosity No Data Available Hazardous Air Pollutants 0 % weight [Test Method:Calculated] Volatile Organic Compounds <=3 % weight [Test Method:calculated per CARB title 2] Volatile Organic Compounds <=0.30 g/l [Test Method:calculated SCAQMD rule 443.1] 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 6 of 12 VOC Less H2O & Exempt Solvents <=30 g/l [Test Method:calculated SCAQMD rule 443.1] SECTION 10: Stability and reactivity 10.1. Reactivity This material may be reactive with certain agents under certain conditions - see the remaining headings in this section. 10.2. Chemical stability Stable. 10.3. Possibility of hazardous reactions Hazardous polymerization will not occur. 10.4. Conditions to avoid None known. 10.5. Incompatible materials Strong oxidizing agents 10.6. Hazardous decomposition products Substance Condition Formaldehyde Heat Refer to section 5.2 for hazardous decomposition products during combustion. SECTION 11: Toxicological information The information below may not be consistent with the material classification in Section 2 if specific ingredient classifications are mandated by a competent authority. In addition, toxicological data on ingredients may not be reflected in the material classification and/or the signs and symptoms of exposure, because an ingredient may be present below the threshold for labeling, an ingredient may not be available for exposure, or the data may not be relevant to the material as a whole. 11.1. Information on Toxicological effects Signs and Symptoms of Exposure Based on test data and/or information on the components, this material may produce the following health effects: Inhalation: May be harmful if inhaled. Respiratory Tract Irritation: Signs/symptoms may include cough, sneezing, nasal discharge, headache, hoarseness, and nose and throat pain. Skin Contact: Skin Irritation: Signs/symptoms may include localized redness, swelling, itching, dryness, cracking, blistering, and pain. Eye Contact: Severe Eye Irritation: Signs/symptoms may include significant redness, swelling, pain, tearing, cloudy appearance of the cornea, and impaired vision. Ingestion: Gastrointestinal Irritation: Signs/symptoms may include abdominal pain, stomach upset, nausea, vomiting and diarrhea. 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 7 of 12 Additional Health Effects: Reproductive/Developmental Toxicity: Contains a chemical or chemicals which can cause birth defects or other reproductive harm. Carcinogenicity: Contains a chemical or chemicals which can cause cancer. Ingredient CAS No. Class Description Regulation Carbon Black 1333-86-4 Grp. 2B: Possible human carc. International Agency for Research on Cancer Toxicological Data If a component is disclosed in section 3 but does not appear in a table below, either no data are available for that endpoint or the data are not sufficient for classification. Acute Toxicity Name Route Species Value Overall product Dermal No data available; calculated ATE >5,000 mg/kg Overall product Inhalation- Dust/Mist(4 hr) No data available; calculated ATE5 - 12.5 mg/l Overall product Ingestion No data available; calculated ATE >5,000 mg/kg Siloxanes and Silicones, Di-me, Hydroxy-terminated Dermal Rabbit LD50 > 16,000 mg/kg Siloxanes and Silicones, Di-me, Hydroxy-terminated Ingestion Rat LD50 > 64,000 mg/kg Poly(Dimethylsiloxane) Dermal Rabbit LD50 > 19,400 mg/kg Silica Dermal Rabbit LD50 > 5,000 mg/kg Solvent Refined Hydrotreated Middle Distillate Dermal Rabbit LD50 > 2,000 mg/kg Poly(Dimethylsiloxane) Ingestion Rat LD50 > 17,000 mg/kg Silica Inhalation- Dust/Mist (4 hours) Rat LC50 > 0.691 mg/l Silica Ingestion Rat LD50 > 5,110 mg/kg Solvent Refined Hydrotreated Middle Distillate Inhalation- Dust/Mist (4 hours) Rat LC50 4.6 mg/l Solvent Refined Hydrotreated Middle Distillate Ingestion Rat LD50 > 5,000 mg/kg Ethyltriacetoxysilane Ingestion Rat LD50 1,462 mg/kg Methyltriacetoxysilane Ingestion Rat LD50 1,602 mg/kg Decamethylcyclopentasiloxane Dermal Rabbit LD50 > 15,000 mg/kg Decamethylcyclopentasiloxane Inhalation- Dust/Mist (4 hours) Rat LC50 8.7 mg/l Decamethylcyclopentasiloxane Ingestion Rat LD50 > 24,134 mg/kg Octamethylcyclotetrasiloxane Dermal Rat LD50 > 2,400 mg/kg Octamethylcyclotetrasiloxane Inhalation- Dust/Mist (4 hours) Rat LC50 36 mg/l Octamethylcyclotetrasiloxane Ingestion Rat LD50 > 5,000 mg/kg Carbon Black Dermal Rabbit LD50 > 3,000 mg/kg Carbon Black Ingestion Rat LD50 > 8,000 mg/kg ATE = acute toxicity estimate Skin Corrosion/Irritation Name Species Value Poly(Dimethylsiloxane) Rabbit No significant irritation Silica Rabbit No significant irritation Solvent Refined Hydrotreated Middle Distillate Rabbit Minimal irritation Ethyltriacetoxysilane Rabbit Corrosive Methyltriacetoxysilane Rabbit Corrosive 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 8 of 12 Decamethylcyclopentasiloxane Rabbit No significant irritation Octamethylcyclotetrasiloxane Rabbit Minimal irritation Carbon Black Rabbit No significant irritation Serious Eye Damage/Irritation Name Species Value Poly(Dimethylsiloxane) Rabbit No significant irritation Silica Rabbit No significant irritation Solvent Refined Hydrotreated Middle Distillate Not available Mild irritant Ethyltriacetoxysilane similar health hazards Corrosive Methyltriacetoxysilane Rabbit Corrosive Decamethylcyclopentasiloxane Rabbit No significant irritation Octamethylcyclotetrasiloxane Rabbit No significant irritation Carbon Black Rabbit No significant irritation Skin Sensitization Name Species Value Silica Human and animal Not classified Decamethylcyclopentasiloxane Mouse Not classified Octamethylcyclotetrasiloxane Human and animal Not classified Respiratory Sensitization For the component/components, either no data are currently available or the data are not sufficient for classification. Germ Cell Mutagenicity Name Route Value Siloxanes and Silicones, Di-me, Hydroxy-terminated In Vitro Not mutagenic Silica In Vitro Not mutagenic Solvent Refined Hydrotreated Middle Distillate In Vitro Some positive data exist, but the data are not sufficient for classification Decamethylcyclopentasiloxane In Vitro Not mutagenic Decamethylcyclopentasiloxane In vivo Not mutagenic Octamethylcyclotetrasiloxane In Vitro Some positive data exist, but the data are not sufficient for classification Carbon Black In Vitro Not mutagenic Carbon Black In vivo Some positive data exist, but the data are not sufficient for classification Carcinogenicity Name Route Species Value Silica Not Specified Mouse Some positive data exist, but the data are not sufficient for classification Solvent Refined Hydrotreated Middle Distillate Dermal Mouse Some positive data exist, but the data are not sufficient for classification Decamethylcyclopentasiloxane Inhalation Rat Some positive data exist, but the data are not sufficient for classification Carbon Black Dermal Mouse Not carcinogenic Carbon Black Ingestion Mouse Not carcinogenic Carbon Black Inhalation Rat Carcinogenic Reproductive Toxicity Reproductive and/or Developmental Effects 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 9 of 12 Name Route Value Species Test Result Exposure Duration Silica Ingestion Not classified for female reproduction Rat NOAEL 509 mg/kg/day 1 generation Silica Ingestion Not classified for male reproduction Rat NOAEL 497 mg/kg/day 1 generation Silica Ingestion Not classified for development Rat NOAEL 1,350 mg/kg/day during organogenesi s Decamethylcyclopentasiloxane Inhalation Not classified for female reproduction Rat NOAEL 2.43 mg/l 2 generation Decamethylcyclopentasiloxane Inhalation Not classified for male reproduction Rat NOAEL 2.43 mg/l 2 generation Decamethylcyclopentasiloxane Inhalation Not classified for development Rat NOAEL 2.43 mg/l 2 generation Octamethylcyclotetrasiloxane Inhalation Not classified for male reproduction Rat NOAEL 8.5 mg/l 2 generation Octamethylcyclotetrasiloxane Ingestion Toxic to female reproduction Rabbit NOAEL 50 mg/kg/day during organogenesi s Octamethylcyclotetrasiloxane Inhalation Toxic to female reproduction Rat NOAEL 3.6 mg/l 2 generation Target Organ(s) Specific Target Organ Toxicity - single exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Solvent Refined Hydrotreated Middle Distillate Inhalation central nervous system depression | respiratory irritation Some positive data exist, but the data are not sufficient for classification Not available NOAEL NA Solvent Refined Hydrotreated Middle Distillate Ingestion central nervous system depression May cause drowsiness or dizziness Not available NOAEL NA Ethyltriacetoxysilane Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification similar health hazards NOAEL Not available Methyltriacetoxysilane Inhalation respiratory irritation Some positive data exist, but the data are not sufficient for classification similar health hazards NOAEL Not available Specific Target Organ Toxicity - repeated exposure Name Route Target Organ(s) Value Species Test Result Exposure Duration Silica Inhalation respiratory system | silicosis Not classified Human NOAEL Not available occupational exposure Decamethylcyclopentasilo xane Dermal hematopoietic system | eyes Not classified Rat NOAEL 1,600 mg/kg/day 28 days Decamethylcyclopentasilo xane Inhalation hematopoietic system | respiratory system | liver | eyes | kidney and/or bladder Not classified Rat NOAEL 2.42 mg/l 2 years Decamethylcyclopentasilo xane Ingestion liver | immune system | respiratory system | heart | hematopoietic system | kidney and/or bladder Not classified Rat NOAEL 1,000 mg/kg/day 90 days Octamethylcyclotetrasiloxa ne Dermal hematopoietic system Not classified Rabbit NOAEL 960 mg/kg/day 3 weeks Octamethylcyclotetrasiloxa ne Inhalation liver Not classified Rat NOAEL 8.5 mg/l 13 weeks Octamethylcyclotetrasiloxa ne Inhalation endocrine system | immune system | Not classified Rat NOAEL 8.5 mg/l 2 generation 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 10 of 12 kidney and/or bladder Octamethylcyclotetrasiloxa ne Inhalation hematopoietic system Not classified Rat NOAEL 8.5 mg/l 13 weeks Octamethylcyclotetrasiloxa ne Ingestion liver Not classified Rat NOAEL 1,600 mg/kg/day 2 weeks Carbon Black Inhalation pneumoconiosis Not classified Human NOAEL Not available occupational exposure Aspiration Hazard Name Value Solvent Refined Hydrotreated Middle Distillate Aspiration hazard Please contact the address or phone number listed on the first page of the SDS for additional toxicological information on this material and/or its components. SECTION 12: Ecological information Ecotoxicological information Please contact the address or phone number listed on the first page of the SDS for additional ecotoxicological information on this material and/or its components. Chemical fate information Please contact the address or phone number listed on the first page of the SDS for additional chemical fate information on this material and/or its components. SECTION 13: Disposal considerations 13.1. Disposal methods Dispose of contents/ container in accordance with the local/regional/national/international regulations. Dispose of waste product in a permitted industrial waste facility. As a disposal alternative, incinerate in a permitted waste incineration facility. Proper destruction may require the use of additional fuel during incineration processes. Empty drums/barrels/containers used for transporting and handling hazardous chemicals (chemical substances/mixtures/preparations classified as Hazardous as per applicable regulations) shall be considered, stored, treated & disposed of as hazardous wastes unless otherwise defined by applicable waste regulations. Consult with the respective regulating authorities to determine the available treatment and disposal facilities. SECTION 14: Transport Information For Transport Information, please visit http://3M.com/Transportinfo or call 1-800-364-3577 or 651-737-6501. SECTION 15: Regulatory information 15.1. US Federal Regulations Contact 3M for more information. EPCRA 311/312 Hazard Classifications: Physical Hazards Not applicable 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 11 of 12 Health Hazards Carcinogenicity Reproductive toxicity Serious eye damage or eye irritation Skin Corrosion or Irritation This material contains a chemical which requires export notification under TSCA Section 12[b]: Ingredient (Category if applicable) C.A.S. No Regulation Status Octamethylcyclotetrasiloxane 556-67-2 Toxic Substances Control Act (TSCA) 4 Test Rule Chemicals Applicable 15.2. State Regulations Contact 3M for more information. California Proposition 65 Ingredient C.A.S. No. Listing Carbon Black 1333-86-4 Carcinogen 15.3. Chemical Inventories The components of this product are in compliance with the chemical notification requirements of TSCA. All required components of this product are listed on the active portion of the TSCA Inventory. Contact 3M for more information. 15.4. International Regulations Contact 3M for more information. This SDS has been prepared to meet the U.S. OSHA Hazard Communication Standard, 29 CFR 1910.1200. SECTION 16: Other information NFPA Hazard Classification Health: 2 Flammability: 1 Instability: 0 Special Hazards: None National Fire Protection Association (NFPA) hazard ratings are designed for use by emergency response personnel to address the hazards that are presented by short-term, acute exposure to a material under conditions of fire, spill, or similar emergencies. Hazard ratings are primarily based on the inherent physical and toxic properties of the material but also include the toxic properties of combustion or decomposition products that are known to be generated in significant quantities. HMIS Hazard Classification Health: 2 Flammability: 1 Physical Hazard: 0 Personal Protection: X - See PPE section. Hazardous Material Identification System (HMIS? IV) hazard ratings are designed to inform employees of chemical hazards in the workplace. These ratings are based on the inherent properties of the material under expected conditions of normal use and are not intended for use in emergency situations. HMIS? IV ratings are to be used with a fully implemented HMIS? IV program. HMIS? is a registered mark of the American Coatings Association (ACA). Document Group: 31-7612-0 Version Number: 2.01 Issue Date: 05/24/18 Supercedes Date: 04/29/14 3M? Super Silicone Sealant (Black), 08662, 08664 05/24/18 __________________________________________________________________________________________ Page 12 of 12 DISCLAIMER: The information in this Safety Data Sheet (SDS) is believed to be correct as of the date issued.3MMAKES NO WARRANTIES, EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE OR COURSE OF PERFORMANCE OR USAGE OF TRADE.User is responsible for determining whether the3Mproduct is fit for a particular purpose and suitable for user's method of use or application.Given the variety of factors that can affect the use and application of a3Mproduct, some of which are uniquely within the user's knowledge and control,it is essential that the user evaluate the3Mproduct to determine whether it is fit for a particular purpose and suitable for user's method of use or application. 3Mprovides information in electronic form as a service to its customers. Due to the remote possibility that electronic transfer may have resulted in errors, omissions or alterations in this information,3Mmakes no representations as to its completeness or accuracy. In addition, information obtained from a database may not be as current as the information in the SDS available directly from3M 3M USA SDSs are available at www.3M.com