SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 1 / 12 SECTION 1. IDENTIFICATION Product name : CYCLO NO7 CLEARCOAT POL CMPD 12/8OZ Product code : 6610 Manufacturer or supplier's details Company name of supplier : Niteo Products, LLC Address : Dallas TX 75225 Email Address : This email address is being protected from spambots. You need JavaScript enabled to view it. Telephone : 1-844-696-4836 Emergency telephone num- ber : 1-800-424-9300 / 1-703-741-5970 Recommended use of the chemical and restrictions on use Recommended use : POLISH Restrictions on use : Use only outdoors or in a well-ventilated area. SECTION 2. HAZARDS IDENTIFICATION GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR 1910.1200) Skin irritation : Category 2 Eye irritation : Category 2A Skin sensitisation : Category 1 Aspiration hazard : Category 1 GHS label elements Hazard pictograms : Signal word : Danger Hazard statements : May be fatal if swallowed and enters airways. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 2 / 12 Precautionary statements : Prevention: Avoid breathing dust/ fume/ gas/ mist/ vapours/ spray. Wash skin thoroughly after handling. Contaminated work clothing should not be allowed out of the workplace. Wear protective gloves/ eye protection/ face protection. Response: IF SWALLOWED: Immediately call a POISON CENTER/ doctor. IF ON SKIN: Wash with plenty of soap and water. IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Do NOT induce vomiting. If skin irritation or rash occurs: Get medical advice/ attention. If eye irritation persists: Get medical advice/ attention. Take off contaminated clothing and wash before reuse. Storage: Store locked up. Disposal: Dispose of contents/ container to an approved waste disposal plant. Other hazards None known. SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance / Mixture : Mixture Hazardous components Chemical name CAS-No. Concentration (% w/w) Kerosene 8008-20-6 >= 10 - < 20 Kaolin 1332-58-7 >= 5 - < 10 Sodium hydroxide 1310-73-2 >= 1 - < 3 Iodopropynyl Butylcarbamate 55406-53-6 >= 0.1 - < 1 Any concentration shown as a range is to protect confidentiality or is due to batch variation. SECTION 4. FIRST AID MEASURES General advice : Move out of dangerous area. Show this safety data sheet to the doctor in attendance. Symptoms of poisoning may appear several hours later. Do not leave the victim unattended. If inhaled : If breathed in, move person into fresh air. If unconscious, place in recovery position and seek medical advice. SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 3 / 12 If symptoms persist, call a physician. In case of skin contact : If on clothes, remove clothes. Remove contaminated clothing. If irritation develops, get med- ical attention. If on skin, rinse well with water. Wash contaminated clothing before re-use. If skin irritation persists, call a physician. In case of eye contact : Immediately flush eye(s) with plenty of water. Remove contact lenses. Protect unharmed eye. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist. If swallowed : Obtain medical attention. Do NOT induce vomiting. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician. Most important symptoms and effects, both acute and delayed : May be fatal if swallowed and enters airways. Causes skin irritation. May cause an allergic skin reaction. Causes serious eye irritation. SECTION 5. FIREFIGHTING MEASURES Suitable extinguishing media : Water spray Carbon dioxide (CO2) Unsuitable extinguishing media : High volume water jet Specific hazards during fire- fighting : If product is heated above its flash point it will produce vapors sufficient to support combustion. Vapors are heavier than air and may travel along the ground and be ignited by heat, pilot lights, other flames and ignition sources at locations near the point of release. Do not allow run-off from fire fighting to enter drains or water courses. Hazardous combustion prod- ucts : Carbon oxides Sodium oxides Specific extinguishing meth- ods : Product is compatible with standard fire-fighting agents. Further information : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. Special protective equipment : In the event of fire, wear self-contained breathing apparatus. SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 4 / 12 for firefighters SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Use personal protective equipment. Ensure adequate ventilation. Avoid breathing dust. Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Environmental precautions : Prevent further leakage or spillage if safe to do so. Prevent product from entering drains. Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities. Methods and materials for containment and cleaning up : Soak up with inert absorbent material (e.g. sand, silica gel, acid binder, universal binder, sawdust). Keep in suitable, closed containers for disposal. SECTION 7. HANDLING AND STORAGE Advice on protection against fire and explosion : Normal measures for preventive fire protection. Advice on safe handling : Do not breathe vapours/dust. Do not smoke. Avoid contact with skin and eyes. Persons susceptible to skin sensitisation problems or asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this mixture is being used. Dispose of rinse water in accordance with local and national regulations. Container hazardous when empty. Smoking, eating and drinking should be prohibited in the ap- plication area. For personal protection see section 8. Conditions for safe storage : Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Observe label precautions. Further information on stor- age stability : No decomposition if stored and applied as directed. SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Components with workplace control parameters Components CAS-No. Value type Control parame- Basis SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 5 / 12 (Form of exposure) ters / Permissible concentration Kerosene 8008-20-6 TWA 100 mg/m3 NIOSH REL TWA 500 ppm 2,000 mg/m3 OSHA Z-1 TWA 200 mg/m3 (total hydrocarbon vapor) ACGIH TWA 400 ppm 1,600 mg/m3 OSHA P0 Kaolin 1332-58-7 TWA (Res- pirable par- ticulate mat- ter) 2 mg/m3 ACGIH TWA (Res- pirable) 5 mg/m3 NIOSH REL TWA (total) 10 mg/m3 NIOSH REL TWA (total dust) 15 mg/m3 OSHA Z-1 TWA (respir- able fraction) 5 mg/m3 OSHA Z-1 TWA (Total dust) 10 mg/m3 OSHA P0 TWA (respir- able dust fraction) 5 mg/m3 OSHA P0 Sodium hydroxide 1310-73-2 C 2 mg/m3 ACGIH C 2 mg/m3 NIOSH REL TWA 2 mg/m3 OSHA Z-1 C 2 mg/m3 OSHA P0 Hazardous components without workplace control parameters Components CAS-No. Iodopropynyl Butylcarbamate 55406-53-6 Engineering measures : Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below exposure guidelines (if applicable) or below levels that cause known, suspected or apparent adverse effects. Personal protective equipment Hand protection Remarks : Wear resistant gloves (consult your safety equipment suppli- er). The suitability for a specific workplace should be dis- cussed with the producers of the protective gloves. Discard gloves that show tears, pinholes, or signs of wear. Eye protection : Wear chemical splash goggles when there is the potential for exposure of the eyes to liquid, vapor or mist. Skin and body protection : Choose body protection according to the amount and con- centration of the dangerous substance at the work place. Wear as appropriate: SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 6 / 12 Impervious clothing Safety shoes Hygiene measures : Handle in accordance with good industrial hygiene and safety practice. When using do not smoke. When using do not eat or drink. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : liquid Colour : light brown Odour : hydrocarbon-like Odour Threshold : No data available pH : No data available Melting point/range : No data available Boiling point/boiling range : No data available Flash point : 93.34 ?C Method: closed cup Evaporation rate : No data available Self-ignition : No data available Upper explosion limit / Upper flammability limit : No data available Lower explosion limit / Lower flammability limit : No data available Vapour pressure : No data available Relative vapour density : No data available Density : 8.3 lb/gal Solubility(ies) Water solubility : soluble Partition coefficient: n- octanol/water : No data available Decomposition temperature : No data available Viscosity Viscosity, dynamic : No data available SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 7 / 12 Viscosity, kinematic : No data available Molecular weight : No data available VOC % By Weight : 9.5 % SECTION 10. STABILITY AND REACTIVITY Reactivity : No decomposition if stored and applied as directed. Chemical stability : No decomposition if stored and applied as directed. Possibility of hazardous reac- tions : No decomposition if stored and applied as directed. Hazardous polymerisation does not occur. Conditions to avoid : No data available Incompatible materials : Strong oxidizing agents Strong acids Strong reducing agents Hazardous decomposition products : Carbon oxides Sodium oxides SECTION 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Inhalation Eye contact Skin contact Ingestion Acute toxicity Not classified based on available information. Product: Acute inhalation toxicity : Acute toxicity estimate: > 200 mg/l Exposure time: 4 h Test atmosphere: dust/mist Method: Calculation method Components: Kerosene: Acute oral toxicity : LD50 (Rat): > 5,000 mg/kg Method: OECD Test Guideline 420 Acute inhalation toxicity : LC50 (Rat): > 5.8 mg/l Exposure time: 4 h Test atmosphere: vapour Method: OECD Test Guideline 403 Assessment: No adverse effect has been observed in acute SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 8 / 12 inhalation toxicity tests. Acute dermal toxicity : LD50 (Rabbit): > 2,000 mg/kg Method: OECD Test Guideline 402 Assessment: No adverse effect has been observed in acute dermal toxicity tests. Kaolin: Acute oral toxicity : LD50 (Rat): > 5,000 mg/kg Acute dermal toxicity : LD50 (Rabbit): > 5,000 mg/kg Sodium hydroxide: Acute oral toxicity : LDLo (Rabbit): 500 mg/kg Iodopropynyl Butylcarbamate: Acute oral toxicity : LD50 (Rat, male and female): 1,470 mg/kg Method: OECD Test Guideline 401 Acute inhalation toxicity : LC50 (Rat): 0.68 mg/l Exposure time: 4 h Test atmosphere: dust/mist Acute dermal toxicity : LD50 (Rabbit): > 2,000 mg/kg Assessment: No adverse effect has been observed in acute dermal toxicity tests. Skin corrosion/irritation Causes skin irritation. Product: Remarks: May cause skin irritation and/or dermatitis. Components: Kerosene: Result: Irritating to skin. Kaolin: Assessment: No skin irritation Result: No skin irritation Sodium hydroxide: Result: Corrosive after 3 minutes or less of exposure Iodopropynyl Butylcarbamate: Species: Rabbit Result: Possibly irritating to skin SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 9 / 12 Serious eye damage/eye irritation Causes serious eye irritation. Product: Remarks: Vapours may cause irritation to the eyes, respiratory system and the skin. Components: Kerosene: Result: Possibly irritating to eyes Kaolin: Result: No eye irritation Assessment: No eye irritation Sodium hydroxide: Result: Corrosive Iodopropynyl Butylcarbamate: Species: Rabbit Result: Corrosive Respiratory or skin sensitisation Skin sensitisation May cause an allergic skin reaction. Respiratory sensitisation Not classified based on available information. Product: Remarks: May cause allergic skin reaction. Components: Sodium hydroxide: Exposure routes: Skin contact Species: Humans Result: negative Iodopropynyl Butylcarbamate: Test Type: Maximisation Test Species: Guinea pig Result: May cause sensitisation by skin contact. Germ cell mutagenicity Not classified based on available information. Carcinogenicity Not classified based on available information. SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 10 / 12 IARC No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. OSHA No component of this product present at levels greater than or equal to 0.1% is on OSHA?s list of regulated carcinogens. NTP No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP. Reproductive toxicity Not classified based on available information. STOT - single exposure Not classified based on available information. Components: Kerosene: Assessment: May cause drowsiness or dizziness. STOT - repeated exposure Not classified based on available information. Components: Iodopropynyl Butylcarbamate: Exposure routes: Inhalation Target Organs: larynx Assessment: Causes damage to organs through prolonged or repeated exposure. Aspiration toxicity May be fatal if swallowed and enters airways. Components: Kerosene: May be fatal if swallowed and enters airways. Further information Product: Remarks: No data available SECTION 12. ECOLOGICAL INFORMATION Toxicity Additional ecological information : An environmental hazard cannot be excluded in the event of unprofessional handling or disposal. Harmful to aquatic life with long lasting effects. SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 11 / 12 SECTION 13. DISPOSAL CONSIDERATIONS Disposal methods Waste from residues : Dispose of in accordance with all applicable local, state and federal regulations. Contaminated packaging : Empty remaining contents. Dispose of as unused product. Do not re-use empty containers. SECTION 14. TRANSPORT INFORMATION Dangerous goods descriptions (if indicated below) may not reflect quantity, end-use, or region-specific exceptions that can be applied. Consult shipping documents for descriptions that are specific to the shipment. International Regulations IATA-DGR Not regulated as a dangerous good IMDG-Code Not regulated as a dangerous good Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Not applicable for product as supplied. National Regulations 49 CFR Not regulated as a dangerous good 49 CFR Not regulated as a dangerous good SECTION 15. REGULATORY INFORMATION EPCRA - Emergency Planning and Community Right-to-Know Act CERCLA Reportable Quantity Components CAS-No. Component RQ (lbs) Calculated product RQ (lbs) Sodium hydroxide 1310-73-2 1000 * *: Calculated RQ exceeds reasonably attainable upper limit. SARA 304 Extremely Hazardous Substances Reportable Quantity This material does not contain any components with a section 304 EHS RQ. SARA 302 Extremely Hazardous Substances Threshold Planning Quantity This material does not contain any components with a section 302 EHS TPQ. SARA 311/312 Hazards : Skin corrosion or irritation Serious eye damage or eye irritation Respiratory or skin sensitisation SAFETY DATA SHEET CYCLO? NO7 CLEARCOAT POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001202 Date of last issue: 08/06/2021 Date of first issue: 08/28/2017 12 / 12 Aspiration hazard SARA 313 : This material does not contain any chemical components with known CAS numbers that exceed the threshold (De Minimis) reporting levels established by SARA Title III, Section 313. California Prop. 65 This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm. SECTION 16. OTHER INFORMATION Further information NFPA: Revision Date : 03/29/2023 The information provided in this Safety Data Sheet is correct to the best of our knowledge, infor- mation and belief at the date of its publication. The information given is designed only as a guid- ance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. US / EN Flammability H e a lt h In s ta b ility 2 1 0 Special hazard