SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 1 / 13 SECTION 1. IDENTIFICATION Product name : CYCLO NO7 WHITE POL CMPD 12/10 OZ TUB Product code : 7610 Manufacturer or supplier's details Company name of supplier : Niteo Products, LLC Address : Dallas TX 75225 Email Address : This email address is being protected from spambots. You need JavaScript enabled to view it. Telephone : 1-844-696-4836 Emergency telephone num- ber : 1-800-424-9300 / 1-703-741-5970 Recommended use of the chemical and restrictions on use Recommended use : POLISH Restrictions on use : Use only outdoors or in a well-ventilated area. SECTION 2. HAZARDS IDENTIFICATION GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR 1910.1200) Skin irritation : Category 2 Skin sensitisation : Category 1 Germ cell mutagenicity : Category 1B Carcinogenicity : Category 1A Specific target organ toxicity - repeated exposure (Inhala- tion) : Category 1 (Kidney) GHS label elements Hazard pictograms : Signal word : Danger Hazard statements : Causes skin irritation. May cause an allergic skin reaction. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 2 / 13 May cause genetic defects. May cause cancer. Causes damage to organs (Kidney) through prolonged or re- peated exposure if inhaled. Precautionary statements : Prevention: Obtain special instructions before use. Do not handle until all safety precautions have been read and understood. Do not breathe dust/ fume/ gas/ mist/ vapours/ spray. Wash skin thoroughly after handling. Do not eat, drink or smoke when using this product. Contaminated work clothing should not be allowed out of the workplace. Wear protective gloves/ protective clothing/ eye protection/ face protection. Response: IF ON SKIN: Wash with plenty of soap and water. IF exposed or concerned: Get medical advice/ attention. If skin irritation or rash occurs: Get medical advice/ attention. Take off contaminated clothing and wash before reuse. Storage: Store locked up. Disposal: Dispose of contents/ container to an approved waste disposal plant. Other hazards None known. SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance / Mixture : Mixture Hazardous components Chemical name CAS-No. Concentration (% w/w) Aluminum oxide 1344-28-1 >= 10 - < 20 Kerosene 8008-20-6 >= 10 - < 20 Silica, crystalline 1317-95-9 >= 5 - < 10 Iodopropynyl Butylcarbamate 55406-53-6 >= 0.1 - < 1 Any concentration shown as a range is to protect confidentiality or is due to batch variation. SECTION 4. FIRST AID MEASURES General advice : Move out of dangerous area. Show this safety data sheet to the doctor in attendance. Do not leave the victim unattended. If inhaled : If unconscious, place in recovery position and seek medical advice. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 3 / 13 If symptoms persist, call a physician. In case of skin contact : If on clothes, remove clothes. Remove contaminated clothing. If irritation develops, get med- ical attention. If on skin, rinse well with water. Wash contaminated clothing before re-use. If skin irritation persists, call a physician. In case of eye contact : Flush eyes with water as a precaution. Remove contact lenses. Protect unharmed eye. Keep eye wide open while rinsing. If swallowed : Obtain medical attention. Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician. Most important symptoms and effects, both acute and delayed : May be fatal if swallowed and enters airways. Causes skin irritation. May cause an allergic skin reaction. May cause genetic defects. May cause cancer. Causes damage to organs through prolonged or repeated exposure if inhaled. SECTION 5. FIREFIGHTING MEASURES Suitable extinguishing media : Water spray Unsuitable extinguishing media : High volume water jet Specific hazards during fire- fighting : If product is heated above its flash point it will produce vapors sufficient to support combustion. Vapors are heavier than air and may travel along the ground and be ignited by heat, pilot lights, other flames and ignition sources at locations near the point of release. Do not allow run-off from fire fighting to enter drains or water courses. Hazardous combustion prod- ucts : Carbon oxides Specific extinguishing meth- ods : Product is compatible with standard fire-fighting agents. Further information : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Fire residues and contaminated fire extinguishing water must be disposed of in accordance with local regulations. Special protective equipment for firefighters : In the event of fire, wear self-contained breathing apparatus. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 4 / 13 SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Use personal protective equipment. Avoid dust formation. Avoid breathing dust. Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Environmental precautions : Prevent further leakage or spillage if safe to do so. Prevent product from entering drains. Do not flush into surface water or sanitary sewer system. If the product contaminates rivers and lakes or drains inform respective authorities. Methods and materials for containment and cleaning up : Keep in suitable, closed containers for disposal. SECTION 7. HANDLING AND STORAGE Advice on protection against fire and explosion : Take measures to prevent the build up of electrostatic charge. Avoid dust formation. Provide appropriate exhaust ventilation at places where dust is formed. Advice on safe handling : Avoid creating dust. Do not breathe vapours/dust. Do not smoke. Avoid contact with skin and eyes. Persons susceptible to skin sensitisation problems or asthma, allergies, chronic or recurrent respiratory disease should not be employed in any process in which this mixture is being used. Dispose of rinse water in accordance with local and national regulations. Container hazardous when empty. Smoking, eating and drinking should be prohibited in the ap- plication area. For personal protection see section 8. Conditions for safe storage : Keep container tightly closed in a dry and well-ventilated place. Containers which are opened must be carefully resealed and kept upright to prevent leakage. Observe label precautions. Further information on stor- age stability : No decomposition if stored and applied as directed. SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Components with workplace control parameters Components CAS-No. Value type (Form of Control parame- ters / Permissible Basis SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 5 / 13 exposure) concentration Aluminum oxide 1344-28-1 TWA (total dust) 15 mg/m3 OSHA Z-1 TWA (respir- able fraction) 5 mg/m3 OSHA Z-1 TWA (Total dust) 10 mg/m3 OSHA P0 TWA (respir- able dust fraction) 5 mg/m3 OSHA P0 TWA (Res- pirable par- ticulate mat- ter) 1 mg/m3 (Aluminium) ACGIH Kerosene 8008-20-6 TWA 100 mg/m3 NIOSH REL TWA 500 ppm 2,000 mg/m3 OSHA Z-1 TWA 200 mg/m3 (total hydrocarbon vapor) ACGIH TWA 400 ppm 1,600 mg/m3 OSHA P0 Silica, crystalline 1317-95-9 TWA (Res- pirable dust) 0.05 mg/m3 (Quartz) OSHA Z-1 TWA (respir- able dust fraction) 0.1 mg/m3 OSHA P0 TWA (Res- pirable par- ticulate mat- ter) 0.025 mg/m3 (Silica) ACGIH TWA (Res- pirable dust) 0.05 mg/m3 (Silica) NIOSH REL PEL (respir- able) 0.05 mg/m3 OSHA CARC Hazardous components without workplace control parameters Components CAS-No. Iodopropynyl Butylcarbamate 55406-53-6 Engineering measures : Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below exposure guidelines (if applicable) or below levels that cause known, suspected or apparent adverse effects. Provide appropriate exhaust ventilation at places where dust is formed. Personal protective equipment Respiratory protection : In the case of dust or aerosol formation use respirator with an approved filter. Dust safety masks are recommended when the dust concen- tration is more than 10 mg/m3. Hand protection SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 6 / 13 Remarks : Wear resistant gloves (consult your safety equipment suppli- er). The suitability for a specific workplace should be dis- cussed with the producers of the protective gloves. Discard gloves that show tears, pinholes, or signs of wear. Eye protection : Safety glasses Skin and body protection : Choose body protection according to the amount and con- centration of the dangerous substance at the work place. Wear as appropriate: Safety shoes Hygiene measures : Handle in accordance with good industrial hygiene and safety practice. Avoid breathing dust. When using do not smoke. When using do not eat or drink. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : cream paste Colour : light orange Odour : slight Odour Threshold : No data available pH : 7 - 8 Melting point/freezing point : No data available Boiling point/boiling range : No data available Flash point : 93.33 ?C Method: closed cup Evaporation rate : No data available Flammability (solid, gas) : No data available Self-ignition : No data available Upper explosion limit / Upper flammability limit : No data available Lower explosion limit / Lower flammability limit : No data available Vapour pressure : No data available Relative vapour density : No data available Density : 8.6 lb/gal SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 7 / 13 Solubility(ies) Water solubility : insoluble Partition coefficient: n- octanol/water : No data available Viscosity Viscosity, dynamic : No data available Viscosity, kinematic : No data available Molecular weight : No data available VOC % By Weight : < 10 % SECTION 10. STABILITY AND REACTIVITY Reactivity : No decomposition if stored and applied as directed. Chemical stability : No decomposition if stored and applied as directed. Possibility of hazardous reac- tions : No decomposition if stored and applied as directed. Hazardous polymerisation does not occur. Conditions to avoid : No data available Incompatible materials : Strong oxidizing agents Hazardous decomposition products : Carbon oxides SECTION 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Inhalation Eye contact Skin contact Ingestion Acute toxicity Not classified based on available information. Product: Acute inhalation toxicity : Acute toxicity estimate: 136 mg/l Exposure time: 4 h Test atmosphere: dust/mist Method: Calculation method Remarks: Prolonged or repeated breathing of dust may result in progressive and permanent lung disease (fibrosis) which may cause death from respiratory and/or heart failure. Symp- toms include coughing and difficult breathing which becomes worse with physical activity. Another form of fibrosis, acute silicosis, can occur with expo- SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 8 / 13 sures to very high concentrations of respirable silica over shorter periods of time, sometimes as short as a few months. Symptoms of acute silicosis include progressive shortness of breath, fever, cough and weight loss. Acute silicosis is fatal. Components: Aluminum oxide: Acute oral toxicity : LD50 (Rat): > 5 g/kg Kerosene: Acute oral toxicity : LD50 (Rat): > 5,000 mg/kg Method: OECD Test Guideline 420 Acute inhalation toxicity : LC50 (Rat): > 5.8 mg/l Exposure time: 4 h Test atmosphere: vapour Method: OECD Test Guideline 403 Assessment: No adverse effect has been observed in acute inhalation toxicity tests. Acute dermal toxicity : LD50 (Rabbit): > 2,000 mg/kg Method: OECD Test Guideline 402 Assessment: No adverse effect has been observed in acute dermal toxicity tests. Iodopropynyl Butylcarbamate: Acute oral toxicity : LD50 (Rat, male and female): 1,470 mg/kg Method: OECD Test Guideline 401 Acute inhalation toxicity : LC50 (Rat): 0.68 mg/l Exposure time: 4 h Test atmosphere: dust/mist Acute dermal toxicity : LD50 (Rabbit): > 2,000 mg/kg Assessment: No adverse effect has been observed in acute dermal toxicity tests. Skin corrosion/irritation Causes skin irritation. Product: Remarks: May cause skin irritation and/or dermatitis. Components: Aluminum oxide: Result: Possibly irritating to skin Kerosene: Result: Irritating to skin. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 9 / 13 Silica, crystalline: Result: Possibly irritating to skin Iodopropynyl Butylcarbamate: Species: Rabbit Result: Possibly irritating to skin Serious eye damage/eye irritation Not classified based on available information. Product: Remarks: Product dust may be irritating to eyes, skin and respiratory system. Components: Aluminum oxide: Result: Possibly irritating to eyes Kerosene: Result: Possibly irritating to eyes Silica, crystalline: Result: Possibly irritating to eyes Iodopropynyl Butylcarbamate: Species: Rabbit Result: Corrosive Respiratory or skin sensitisation Skin sensitisation May cause an allergic skin reaction. Respiratory sensitisation Not classified based on available information. Product: Remarks: May cause allergic skin reaction. Components: Aluminum oxide: Assessment: Did not cause sensitisation on laboratory animals. Iodopropynyl Butylcarbamate: Test Type: Maximisation Test Species: Guinea pig Result: May cause sensitisation by skin contact. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 10 / 13 Germ cell mutagenicity May cause genetic defects. Components: Kerosene: Germ cell mutagenicity - Assessment : Presumed to induce heritable mutations in the germ cells of humans. Carcinogenicity May cause cancer. Components: Silica, crystalline: Carcinogenicity - Assess- ment : Human carcinogen. IARC Group 1: Carcinogenic to humans Silica, crystalline 1317-95-9 OSHA No component of this product present at levels greater than or equal to 0.1% is on OSHA?s list of regulated carcinogens. NTP Known to be human carcinogen Silica, crystalline 1317-95-9 Reproductive toxicity Not classified based on available information. STOT - single exposure Not classified based on available information. Components: Kerosene: Assessment: May cause drowsiness or dizziness. STOT - repeated exposure Causes damage to organs (Kidney) through prolonged or repeated exposure if inhaled. Components: Silica, crystalline: Exposure routes: inhalation (dust/mist/fume) Target Organs: Kidney Assessment: Causes damage to organs through prolonged or repeated exposure. Iodopropynyl Butylcarbamate: Exposure routes: Inhalation Target Organs: larynx Assessment: Causes damage to organs through prolonged or repeated exposure. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 11 / 13 Aspiration toxicity May be fatal if swallowed and enters airways. Components: Kerosene: May be fatal if swallowed and enters airways. Further information Product: Remarks: No data available SECTION 12. ECOLOGICAL INFORMATION Toxicity Additional ecological information : An environmental hazard cannot be excluded in the event of unprofessional handling or disposal. Toxic to aquatic life. Harmful to aquatic life with long lasting effects. SECTION 13. DISPOSAL CONSIDERATIONS Disposal methods Waste from residues : Dispose of in accordance with all applicable local, state and federal regulations. Contaminated packaging : Empty remaining contents. Dispose of as unused product. Do not re-use empty containers. SECTION 14. TRANSPORT INFORMATION Dangerous goods descriptions (if indicated below) may not reflect quantity, end-use, or region-specific exceptions that can be applied. Consult shipping documents for descriptions that are specific to the shipment. International Regulations IATA-DGR Not regulated as a dangerous good IMDG-Code Not regulated as a dangerous good Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Not applicable for product as supplied. National Regulations 49 CFR Not regulated as a dangerous good SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 12 / 13 49 CFR Not regulated as a dangerous good SECTION 15. REGULATORY INFORMATION EPCRA - Emergency Planning and Community Right-to-Know Act CERCLA Reportable Quantity Components CAS-No. Component RQ (lbs) Calculated product RQ (lbs) Sodium hydroxide 1310-73-2 1000 * *: Calculated RQ exceeds reasonably attainable upper limit. SARA 304 Extremely Hazardous Substances Reportable Quantity This material does not contain any components with a section 304 EHS RQ. SARA 302 Extremely Hazardous Substances Threshold Planning Quantity This material does not contain any components with a section 302 EHS TPQ. SARA 311/312 Hazards : Skin corrosion or irritation Respiratory or skin sensitisation Germ cell mutagenicity Carcinogenicity Specific target organ toxicity (single or repeated exposure) SARA 313 : The following components are subject to reporting levels es- tablished by SARA Title III, Section 313: Aluminum oxide 1344-28-1 >= 10 - < 20 % California Prop. 65 WARNING: This product can expose you to chemicals including Silica, crystalline, which is/are known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov. SAFETY DATA SHEET CYCLO? NO7 WHITE POLISHING COMPOUND Version 2.1 Revision Date: 03/29/2023 SDS Number: 600000001203 Date of last issue: 05/29/2019 Date of first issue: 08/28/2017 13 / 13 SECTION 16. OTHER INFORMATION Further information NFPA: Revision Date : 03/29/2023 The information provided in this Safety Data Sheet is correct to the best of our knowledge, infor- mation and belief at the date of its publication. The information given is designed only as a guid- ance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. US / EN Flammability H e a lt h In s ta b ility 2 1 0 Special hazard