SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 1 / 10 SECTION 1. IDENTIFICATION Product name : CYCLO NO7 CHROME & METAL POL 12/8OZ Product code : 10120 Manufacturer or supplier's details Company name of supplier : Niteo Products, LLC Address : Dallas TX 75225 Email Address : This email address is being protected from spambots. You need JavaScript enabled to view it. Telephone : 1-844-696-4836 Emergency telephone num- ber : 1-800-424-9300 / 1-703-741-5970 Recommended use of the chemical and restrictions on use Recommended use : POLISH Restrictions on use : Use only outdoors or in a well-ventilated area. SECTION 2. HAZARDS IDENTIFICATION GHS classification in accordance with the OSHA Hazard Communication Standard (29 CFR 1910.1200) Skin irritation : Category 2 Eye irritation : Category 2A GHS label elements Hazard pictograms : Signal word : Warning Hazard statements : Causes skin irritation. Causes serious eye irritation. Precautionary statements : Prevention: Wash skin thoroughly after handling. Wear protective gloves/ eye protection/ face protection. Response: IF ON SKIN: Wash with plenty of soap and water. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 2 / 10 IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. If skin irritation occurs: Get medical advice/ attention. If eye irritation persists: Get medical advice/ attention. Take off contaminated clothing and wash before reuse. Other hazards None known. SECTION 3. COMPOSITION/INFORMATION ON INGREDIENTS Substance / Mixture : Mixture Hazardous components Chemical name CAS-No. Concentration (% w/w) Aluminum oxide 1344-28-1 >= 10 - < 20 Sodium hydroxide 1310-73-2 >= 1 - < 3 Ammonium hydroxide 1336-21-6 >= 1 - < 3 Any concentration shown as a range is to protect confidentiality or is due to batch variation. SECTION 4. FIRST AID MEASURES General advice : Move out of dangerous area. Show this safety data sheet to the doctor in attendance. Do not leave the victim unattended. If inhaled : If breathed in, move person into fresh air. If unconscious, place in recovery position and seek medical advice. If symptoms persist, call a physician. In case of skin contact : If on clothes, remove clothes. Remove contaminated clothing. If irritation develops, get med- ical attention. If on skin, rinse well with water. Wash contaminated clothing before re-use. If skin irritation persists, call a physician. In case of eye contact : Immediately flush eye(s) with plenty of water. Remove contact lenses. Protect unharmed eye. Keep eye wide open while rinsing. If eye irritation persists, consult a specialist. If swallowed : Do not give milk or alcoholic beverages. Never give anything by mouth to an unconscious person. If symptoms persist, call a physician. Most important symptoms and effects, both acute and delayed : Causes skin irritation. Causes serious eye irritation. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 3 / 10 SECTION 5. FIREFIGHTING MEASURES Suitable extinguishing media : Water spray Carbon dioxide (CO2) Unsuitable extinguishing media : High volume water jet Hazardous combustion prod- ucts : Carbon oxides Sodium oxides Specific extinguishing meth- ods : Product is compatible with standard fire-fighting agents. Further information : Use extinguishing measures that are appropriate to local cir- cumstances and the surrounding environment. Special protective equipment for firefighters : In the event of fire, wear self-contained breathing apparatus. SECTION 6. ACCIDENTAL RELEASE MEASURES Personal precautions, protec- tive equipment and emer- gency procedures : Use personal protective equipment. Avoid breathing dust. Persons not wearing protective equipment should be excluded from area of spill until clean-up has been completed. Environmental precautions : Prevent further leakage or spillage if safe to do so. Methods and materials for containment and cleaning up : Keep in suitable, closed containers for disposal. SECTION 7. HANDLING AND STORAGE Advice on protection against fire and explosion : Normal measures for preventive fire protection. Advice on safe handling : Do not breathe vapours/dust. Do not smoke. Avoid contact with skin and eyes. Dispose of rinse water in accordance with local and national regulations. Container hazardous when empty. Smoking, eating and drinking should be prohibited in the ap- plication area. For personal protection see section 8. Conditions for safe storage : Keep container tightly closed in a dry and well-ventilated place. Further information on stor- age stability : No decomposition if stored and applied as directed. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 4 / 10 SECTION 8. EXPOSURE CONTROLS/PERSONAL PROTECTION Components with workplace control parameters Components CAS-No. Value type (Form of exposure) Control parame- ters / Permissible concentration Basis Aluminum oxide 1344-28-1 TWA (total dust) 15 mg/m3 OSHA Z-1 TWA (respir- able fraction) 5 mg/m3 OSHA Z-1 TWA (Total dust) 10 mg/m3 OSHA P0 TWA (respir- able dust fraction) 5 mg/m3 OSHA P0 TWA (Res- pirable par- ticulate mat- ter) 1 mg/m3 (Aluminium) ACGIH Sodium hydroxide 1310-73-2 C 2 mg/m3 ACGIH C 2 mg/m3 NIOSH REL TWA 2 mg/m3 OSHA Z-1 C 2 mg/m3 OSHA P0 Ammonium hydroxide 1336-21-6 TWA 25 ppm (Ammonia) ACGIH STEL 35 ppm (Ammonia) ACGIH TWA 25 ppm 18 mg/m3 (Ammonia) NIOSH REL ST 35 ppm 27 mg/m3 (Ammonia) NIOSH REL Engineering measures : Provide sufficient mechanical (general and/or local exhaust) ventilation to maintain exposure below exposure guidelines (if applicable) or below levels that cause known, suspected or apparent adverse effects. Personal protective equipment Hand protection Remarks : Wear resistant gloves (consult your safety equipment suppli- er). The suitability for a specific workplace should be dis- cussed with the producers of the protective gloves. Discard gloves that show tears, pinholes, or signs of wear. Eye protection : Wear chemical splash goggles when there is the potential for exposure of the eyes to liquid, vapor or mist. Skin and body protection : Choose body protection according to the amount and con- centration of the dangerous substance at the work place. Wear as appropriate: Impervious clothing SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 5 / 10 Safety shoes Hygiene measures : Handle in accordance with good industrial hygiene and safety practice. When using do not smoke. When using do not eat or drink. SECTION 9. PHYSICAL AND CHEMICAL PROPERTIES Appearance : liquid Colour : No data available Odour : ammoniacal Odour Threshold : No data available pH : No data available Melting point/range : No data available Boiling point/boiling range : No data available Flash point : Not applicable Evaporation rate : No data available Flammability (solid, gas) : No data available Self-ignition : No data available Upper explosion limit / Upper flammability limit : No data available Lower explosion limit / Lower flammability limit : No data available Vapour pressure : No data available Relative vapour density : No data available Density : No data available Solubility(ies) Water solubility : soluble Partition coefficient: n- octanol/water : No data available Decomposition temperature : No data available Viscosity Viscosity, kinematic : No data available Molecular weight : No data available SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 6 / 10 VOC % By Weight : 0 % SECTION 10. STABILITY AND REACTIVITY Reactivity : No decomposition if stored and applied as directed. Chemical stability : No decomposition if stored and applied as directed. Possibility of hazardous reac- tions : No decomposition if stored and applied as directed. Hazardous polymerisation does not occur. Conditions to avoid : No data available Hazardous decomposition products : SECTION 11. TOXICOLOGICAL INFORMATION Information on likely routes of exposure Inhalation Eye contact Skin contact Ingestion Acute toxicity Not classified based on available information. Product: Acute oral toxicity : Acute toxicity estimate: > 5,000 mg/kg Method: Calculation method Acute dermal toxicity : Acute toxicity estimate: > 5,000 mg/kg Method: Calculation method Components: Aluminum oxide: Acute oral toxicity : LD50 (Rat): > 5 g/kg Sodium hydroxide: Acute oral toxicity : LDLo (Rabbit): 500 mg/kg Ammonium hydroxide: Acute oral toxicity : LD50 (Rat): 350 mg/kg Skin corrosion/irritation Causes skin irritation. Product: Remarks: May cause skin irritation and/or dermatitis. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 7 / 10 Components: Aluminum oxide: Result: Possibly irritating to skin Sodium hydroxide: Result: Corrosive after 3 minutes or less of exposure Ammonium hydroxide: Result: Corrosive Serious eye damage/eye irritation Causes serious eye irritation. Product: Remarks: Vapours may cause irritation to the eyes, respiratory system and the skin. Components: Aluminum oxide: Result: Possibly irritating to eyes Sodium hydroxide: Result: Corrosive Ammonium hydroxide: Result: Irreversible effects on the eye Respiratory or skin sensitisation Skin sensitisation Not classified based on available information. Respiratory sensitisation Not classified based on available information. Components: Aluminum oxide: Assessment: Did not cause sensitisation on laboratory animals. Sodium hydroxide: Exposure routes: Skin contact Species: Humans Result: negative Germ cell mutagenicity Not classified based on available information. Carcinogenicity Not classified based on available information. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 8 / 10 IARC No component of this product present at levels greater than or equal to 0.1% is identified as probable, possible or confirmed human carcinogen by IARC. OSHA No component of this product present at levels greater than or equal to 0.1% is on OSHA?s list of regulated carcinogens. NTP No component of this product present at levels greater than or equal to 0.1% is identified as a known or anticipated carcinogen by NTP. Reproductive toxicity Not classified based on available information. STOT - single exposure Not classified based on available information. Components: Ammonium hydroxide: Assessment: The substance or mixture is classified as specific target organ toxicant, single ex- posure, category 3 with respiratory tract irritation. STOT - repeated exposure Not classified based on available information. Aspiration toxicity Not classified based on available information. Further information Product: Remarks: No data available SECTION 12. ECOLOGICAL INFORMATION Toxicity Additional ecological information : No data available SECTION 13. DISPOSAL CONSIDERATIONS Disposal methods Waste from residues : Dispose of in accordance with all applicable local, state and federal regulations. Contaminated packaging : Empty remaining contents. Dispose of as unused product. Do not re-use empty containers. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 9 / 10 SECTION 14. TRANSPORT INFORMATION Dangerous goods descriptions (if indicated below) may not reflect quantity, end-use, or region-specific exceptions that can be applied. Consult shipping documents for descriptions that are specific to the shipment. International Regulations IATA-DGR Not regulated as a dangerous good IMDG-Code Not regulated as a dangerous good Transport in bulk according to Annex II of MARPOL 73/78 and the IBC Code Not applicable for product as supplied. National Regulations 49 CFR Not regulated as a dangerous good 49 CFR Not regulated as a dangerous good SECTION 15. REGULATORY INFORMATION EPCRA - Emergency Planning and Community Right-to-Know Act CERCLA Reportable Quantity Components CAS-No. Component RQ (lbs) Calculated product RQ (lbs) Sodium hydroxide 1310-73-2 1000 * Ammonium hydroxide 1336-21-6 1000 * *: Calculated RQ exceeds reasonably attainable upper limit. SARA 304 Extremely Hazardous Substances Reportable Quantity This material does not contain any components with a section 304 EHS RQ. SARA 302 Extremely Hazardous Substances Threshold Planning Quantity This material does not contain any components with a section 302 EHS TPQ. SARA 311/312 Hazards : Skin corrosion or irritation Serious eye damage or eye irritation SARA 313 : The following components are subject to reporting levels es- tablished by SARA Title III, Section 313: Aluminum oxide 1344-28-1 >= 10 - < 20 % California Prop. 65 This product does not contain any chemicals known to State of California to cause cancer, birth defects, or any other reproductive harm. SAFETY DATA SHEET CYCLO? NO7 CHROME & METAL POLISH Version 2.2 Revision Date: 03/29/2023 SDS Number: 600000001206 Date of last issue: 01/05/2023 Date of first issue: 09/05/2017 10 / 10 SECTION 16. OTHER INFORMATION Further information NFPA: Revision Date : 03/29/2023 The information provided in this Safety Data Sheet is correct to the best of our knowledge, infor- mation and belief at the date of its publication. The information given is designed only as a guid- ance for safe handling, use, processing, storage, transportation, disposal and release and is not to be considered a warranty or quality specification. The information relates only to the specific material designated and may not be valid for such material used in combination with any other materials or in any process, unless specified in the text. US / EN Flammability H e a lt h In s ta b ility 2 1 0 Special hazard