SAFETY DATA SHEET1. Identification Liquid Wrench Lubricating OilProduct identifierOther means of identification L212SDS number L212, L206Part No. 3403.19.1000Tariff code LubricantRecommended use None known.Recommended restrictionsManufacturer/Importer/Supplier/Distributor informationManufacturerAddressCompany nameEmergency phone numberTelephoneWebsite2. Hazard(s) identification Category 1Flammable aerosolsPhysical hazards Category 4Acute toxicity, inhalationHealth hazards Category 2ASerious eye damage/eye irritation Category 1BGerm cell mutagenicity Category 3 narcotic effectsSpecific target organ toxicity, single exposure Category 2Specific target organ toxicity, repeatedexposure Category 1Aspiration hazard Category 3Hazardous to the aquatic environment, acutehazardEnvironmental hazards Category 3Hazardous to the aquatic environment,long-term hazardNot classified.OSHA defined hazardsLabel elementsSignal word DangerHazard statement Extremely flammable aerosol. May be fatal if swallowed and enters airways. Causes serious eyeirritation. May cause drowsiness or dizziness. May cause genetic defects. May cause damage toorgans through prolonged or repeated exposure. Harmful to aquatic life. Harmful to aquatic lifewith long lasting effects. 1 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS USBlaster LLC8500 Sweet Valley Drive Valley View, Ohio 44125 - USA T(216)901-5800F (216)901-5801www.blastercorp.comChemtrec (800) 424-9300 Precautionary statementPrevention Obtain special instructions before use. Do not handle until all safety precautions have been readand understood. Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do notspray on an open flame or other ignition source. Pressurized container: Do not pierce or burn,even after use. Do not breathe mist or vapor. Wash thoroughly after handling. Use only outdoorsor in a well-ventilated area. Avoid release to the environment. Wear protective gloves/protectiveclothing/eye protection/face protection.Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If inhaled:Remove person to fresh air and keep comfortable for breathing. If in eyes: Rinse cautiously withwater for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. Ifexposed or concerned: Get medical advice/attention. Call a poison center/doctor if you feelunwell. If eye irritation persists: Get medical advice/attention.Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect fromsunlight. Do not expose to temperatures exceeding 50?C/122?F.Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.Hazard(s) not otherwiseclassified (HNOC) Combustible.Supplemental information NOTE: This product is a consumer product and is labeled in accordance with the US ConsumerProduct Safety Commission regulations which take precedence over OSHA HazardCommunication labeling. The container label may not include the OSHA label elements listed inthis document. Always carefully review the entire SDS and the product label prior to use in theworkplace.3. Composition/information on ingredientsMixtures CAS number %Chemical name Common name and synonyms 64742-47-8ISOPARAFFINIC PETROLEUMDISTILLATE 70 - < 80112-34-5Butoxydiglycol 5 - < 1064742-52-5Distillates (petroleum),Hydrotreated Heavy Naphthenic 5 - < 10124-38-9Carbon Dioxide 1 - < 39002-84-0Polytetrafluoroethylene (PTFE) < 0.23 - < 5Other components below reportable levels 10043-11-5Boron Nitride < 0.1*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.4. First-aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poisoncenter or doctor/physician if you feel unwell.Inhalation Wash off with soap and water. Get medical attention if irritation develops and persists.Skin contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, ifpresent and easy to do. Continue rinsing. If eye irritation persists: Get medical advice/attention.Eye contact Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. Ifvomiting occurs, keep head low so that stomach content doesn't get into the lungs.Ingestion Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,redness, swelling, and blurred vision. Prolonged exposure may cause chronic effects.Most importantsymptoms/effects, acute anddelayed Provide general supportive measures and treat symptomatically. Keep victim under observation.Symptoms may be delayed.Indication of immediatemedical attention and specialtreatment needed IF exposed or concerned: Get medical advice/attention. If you feel unwell, seek medical advice(show the label where possible). Ensure that medical personnel are aware of the material(s)involved, and take precautions to protect themselves. Show this safety data sheet to the doctor inattendance.General information5. Fire-fighting measures Alcohol resistant foam. Powder. Dry chemicals. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishingmedia 2 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US Contents under pressure. Pressurized container may explode when exposed to heat or flame.During fire, gases hazardous to health may be formed.Specific hazards arising fromthe chemical Firefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, SCBA.Special protective equipmentand precautions for firefighters Move containers from fire area if you can do so without risk. Cool containers exposed to heat withwater spray and remove container, if no risk is involved. Containers should be cooled with water toprevent vapor pressure build up. For massive fire in cargo area, use unmanned hose holder ormonitor nozzles, if possible. If not, withdraw and let fire burn out.Fire fightingequipment/instructions Use standard firefighting procedures and consider the hazards of other involved materials. Movecontainers from fire area if you can do so without risk. In the event of fire and/or explosion do notbreathe fumes.Specific methods Extremely flammable aerosol. Combustible.General fire hazards6. Accidental release measuresKeep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wearappropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Donot touch damaged containers or spilled material unless wearing appropriate protective clothing.Ventilate closed spaces before entering them. Local authorities should be advised if significantspillages cannot be contained. For personal protection, see section 8 of the SDS.Personal precautions,protective equipment andemergency procedures Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so withoutrisk. Move the cylinder to a safe and open area if the leak is irreparable. Use water spray to reducevapors or divert vapor cloud drift. Eliminate all ignition sources (no smoking, flares, sparks, orflames in immediate area). Keep combustibles (wood, paper, oil, etc.) away from spilled material.The product is immiscible with water and will spread on the water surface. This material isclassified as a water pollutant under the Clean Water Act and should be prevented fromcontaminating soil or from entering sewage and drainage systems which lead to waterways.Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery,flush area with water.Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly toremove residual contamination. Put material in suitable, covered, labeled containers. For wastedisposal, see section 13 of the SDS.Methods and materials forcontainment and cleaning up Avoid release to the environment. Inform appropriate managerial or supervisory personnel of allenvironmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge intodrains, water courses or onto the ground.Environmental precautions7. Handling and storage Obtain special instructions before use. Do not handle until all safety precautions have been readand understood. Pressurized container: Do not pierce or burn, even after use. Do not use if spraybutton is missing or defective. Do not spray on a naked flame or any other incandescent material.Do not smoke while using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill,grind, or expose containers to heat, flame, sparks, or other sources of ignition. All equipment usedwhen handling the product must be grounded. Do not re-use empty containers. Avoid contact witheyes. Avoid prolonged or repeated contact with skin. Avoid prolonged exposure. Should behandled in closed systems, if possible. Use only outdoors or in a well-ventilated area. Wearappropriate personal protective equipment. Wash hands thoroughly after handling. Avoid releaseto the environment. Observe good industrial hygiene practices.Precautions for safe handling Level 3 Aerosol.Store locked up. Pressurized container. Protect from sunlight and do not expose to temperaturesexceeding 50?C/122 ?F. Do not puncture, incinerate or crush. Do not handle or store near an openflame, heat or other sources of ignition. This material can accumulate static charge which maycause spark and become an ignition source. Store in tightly closed container. Store in awell-ventilated place. Store away from incompatible materials (see Section 10 of the SDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionOccupational exposure limitsThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.At this time, the other constituents have no known exposure limits.US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) FormValueComponents TypePEL 9000 mg/m3Carbon Dioxide (CAS124-38-9) 5000 ppm 3 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) FormValueComponents TypePEL 5 mg/m3 Mist.Distillates (petroleum),Hydrotreated HeavyNaphthenic (CAS64742-52-5) 2000 mg/m3500 ppmPEL 400 mg/m3ISOPARAFFINICPETROLEUM DISTILLATE(CAS 64742-47-8) 100 ppmUS. ACGIH Threshold Limit Values FormValueComponents TypeTWA 10 ppm Inhalable fraction andvapor.Butoxydiglycol (CAS112-34-5) STEL 30000 ppmCarbon Dioxide (CAS124-38-9) TWA 5000 ppmTWA 5 mg/m3 Inhalable fraction.Distillates (petroleum),Hydrotreated HeavyNaphthenic (CAS64742-52-5)US. NIOSH: Pocket Guide to Chemical Hazards FormValueComponents TypeSTEL 54000 mg/m3Carbon Dioxide (CAS124-38-9) 30000 ppmTWA 9000 mg/m35000 ppmCeiling 1800 mg/m3Distillates (petroleum),Hydrotreated HeavyNaphthenic (CAS64742-52-5) STEL 10 mg/m3 Mist.No biological exposure limits noted for the ingredient(s).Biological limit values Good general ventilation (typically 10 air changes per hour) should be used. Ventilation ratesshould be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,or other engineering controls to maintain airborne levels below recommended exposure limits. Ifexposure limits have not been established, maintain airborne levels to an acceptable level. Provideeyewash station.Appropriate engineeringcontrolsIndividual protection measures, such as personal protective equipmentChemical respirator with organic vapor cartridge and full facepiece.Eye/face protectionSkin protection Wear appropriate chemical resistant gloves. Nitrile gloves are recommended.Hand protection Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.Other Chemical respirator with organic vapor cartridge and full facepiece. Chemical respirator withorganic vapor cartridge and full facepiece if threshold limits are exceeded.Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards Observe any medical surveillance requirements. When using do not smoke. Always observe goodpersonal hygiene measures, such as washing after handling the material and before eating,drinking, and/or smoking. Routinely wash work clothing and protective equipment to removecontaminants.General hygieneconsiderations9. Physical and chemical propertiesOpaque LiquidAppearance 4 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US Liquid.Physical state Aerosol.Form YellowColor Sweet VanillaOdorOdor threshold Not available.pH Not available.Melting point/freezing point -54.65 ?F (-48.14 ?C) estimatedInitial boiling point and boilingrange 473.84 ?F (245.47 ?C) estimatedFlash point > 200.0 ?F (> 93.3 ?C) Tag Closed CupEvaporation rate Not available.Not applicable.Flammability (solid, gas)Upper/lower flammability or explosive limitsFlammability limit - lower(%) 0.7 % estimatedFlammability limit - upper(%) 5 % estimatedExplosive limit - lower (%) Not available.Explosive limit - upper (%) Not available.Vapor pressure 10.65811 hPa estimatedVapor density Not available.Relative density Not available.Solubility(ies)Solubility (water) InsolublePartition coefficient(n-octanol/water) Not available.Auto-ignition temperature 522.43 ?F (272.46 ?C) estimatedDecomposition temperature Not available.Viscosity Not available.Other informationDensity 7.41216 lbs/galNot explosive.Explosive propertiesFlammability (flash back) NoHeat of combustion (NFPA30B) 36.74 kJ/g estimatedKinematic viscosity 18 cStKinematic viscositytemperature 104 ?F (40 ?C)Not oxidizing.Oxidizing propertiesSpecific gravity 0.88822VOC 0 % w/w10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability Hazardous polymerization does not occur.Possibility of hazardousreactions Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Avoidtemperatures exceeding the flash point. Contact with incompatible materials.Conditions to avoid Strong oxidizing agents.Incompatible materials No hazardous decomposition products are known.Hazardous decompositionproducts 5 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US 11. Toxicological informationInformation on likely routes of exposureInhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. Prolonged inhalation may beharmful.Skin contact No adverse effects due to skin contact are expected.Eye contact Causes serious eye irritation.Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a seriouschemical pneumonia.Symptoms related to thephysical, chemical andtoxicological characteristics Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,redness, swelling, and blurred vision.Information on toxicological effectsAcute toxicity May be fatal if swallowed and enters airways. Test ResultsComponents SpeciesButoxydiglycol (CAS 112-34-5)DermalAcuteLD50 Rabbit 2700 mg/kgOralLD50 Rat 3306 mg/kgDistillates (petroleum), Hydrotreated Heavy Naphthenic (CAS 64742-52-5)DermalAcuteLD50 Rabbit > 2000 mg/kg, 24 HoursInhalationLC50 Rat > 3.9 mg/l, 4 HoursOralLD50 Rat > 2000 mg/kgProlonged skin contact may cause temporary irritation.Skin corrosion/irritation Causes serious eye irritation.Serious eye damage/eyeirritationRespiratory or skin sensitizationRespiratory sensitization Not a respiratory sensitizer.This product is not expected to cause skin sensitization.Skin sensitization May cause genetic defects.Germ cell mutagenicityCarcinogenicity Not classifiable as to carcinogenicity to humans.IARC Monographs. Overall Evaluation of CarcinogenicityPolytetrafluoroethylene (PTFE) (CAS 9002-84-0) 3 Not classifiable as to carcinogenicity to humans.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.US. National Toxicology Program (NTP) Report on CarcinogensDistillates (petroleum), Hydrotreated Heavy Naphthenic(CAS 64742-52-5) Known To Be Human Carcinogen.Not available.Reproductive toxicitySpecific target organ toxicity -single exposure May cause drowsiness and dizziness.Specific target organ toxicity -repeated exposure May cause damage to organs through prolonged or repeated exposure.Aspiration hazard May be fatal if swallowed and enters airways.Chronic effects May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation maybe harmful. 6 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US 12. Ecological information Harmful to aquatic life with long lasting effects.EcotoxicityComponents Test ResultsSpeciesButoxydiglycol (CAS 112-34-5)Aquatic LC50Fish 1300 mg/l, 96 hoursBluegill (Lepomis macrochirus)ISOPARAFFINIC PETROLEUM DISTILLATE (CAS 64742-47-8)Aquatic EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex)LC50Fish 2.9 mg/l, 96 hoursRainbow trout,donaldson trout(Oncorhynchus mykiss)No data is available on the degradability of any ingredients in the mixture.Persistence and degradabilityBioaccumulative potentialPartition coefficient n-octanol / water (log Kow)Butoxydiglycol 0.56No data available.Mobility in soilOther adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creationpotential, endocrine disruption, global warming potential) are expected from this component.13. Disposal considerationsCollect and reclaim or dispose in sealed containers at licensed waste disposal site. Contentsunder pressure. Do not puncture, incinerate or crush. Do not allow this material to drain intosewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or usedcontainer. Dispose of contents/container in accordance with local/regional/national/internationalregulations.Disposal instructions Dispose in accordance with all applicable regulations.Local disposal regulations The waste code should be assigned in discussion between the user, the producer and the wastedisposal company.Hazardous waste code Dispose of in accordance with local regulations. Empty containers or liners may retain someproduct residues. This material and its container must be disposed of in a safe manner (see:Disposal instructions).Waste from residues / unusedproducts Since emptied containers may retain product residue, follow label warnings even after container isemptied. Empty containers should be taken to an approved waste handling site for recycling ordisposal. Do not re-use empty containers.Contaminated packaging14. Transport informationDOT UN1950UN number Aerosols, flammable, (each not exceeding 1 L capacity), Limited QuantityUN proper shipping name 2.1ClassTransport hazard class(es) -Subsidiary risk 2.1Label(s) Not available.Packing group Read safety instructions, SDS and emergency procedures before handling.Special precautions for user N82Special provisions 306Packaging exceptions NonePackaging non bulk NonePackaging bulkIATA UN1950UN number Aerosol, flammable, Limited QuantityUN proper shipping name 2.1ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group YesEnvironmental hazards 7 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US 9LERG Code Read safety instructions, SDS and emergency procedures before handling.Special precautions for user Allowed with restrictions.Passenger and cargoaircraftOther information Allowed with restrictions.Cargo aircraft onlyIMDG UN1950UN number Aerosols, MARINE POLLUTANT (Petroleum Distillates), Limited QuantityUN proper shipping name 2.1ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group YesMarine pollutantEnvironmental hazards F-D, S-UEmS Read safety instructions, SDS and emergency procedures before handling.Special precautions for userPetroleum Distillates Not established.Transport in bulk according toAnnex II of MARPOL 73/78 andthe IBC CodeDOT; IMDGIATAMarine pollutant IMDG Regulated Marine Pollutant. DOT Regulated Marine Pollutant.General information15. Regulatory informationThis product is a "Hazardous Chemical" as defined by the OSHA Hazard CommunicationStandard, 29 CFR 1910.1200.US federal regulations 8 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)Not regulated.TSCA Chemical Action Plans, Chemicals of ConcernPolytetrafluoroethylene (PTFE) (CAS 9002-84-0) Long-Chain Perfluorinated Chemicals (PFCs) Action PlanCERCLA Hazardous Substance List (40 CFR 302.4)Butoxydiglycol (CAS 112-34-5) Listed.SARA 304 Emergency release notificationNot regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.SARA 302 Extremely hazardous substanceSuperfund Amendments and Reauthorization Act of 1986 (SARA)Not listed. YesSARA 311/312 Hazardouschemical Flammable (gases, aerosols, liquids, or solids)Acute toxicity (any route of exposure)Serious eye damage or eye irritationGerm cell mutagenicitySpecific target organ toxicity (single or repeated exposure)Aspiration hazardClassified hazardcategoriesSARA 313 (TRI reporting)Chemical name % by wt.CAS numberButoxydiglycol 5 - < 10112-34-5Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) ListButoxydiglycol (CAS 112-34-5)Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)Not regulated. Not regulated.Safe Drinking Water Act(SDWA)US state regulationsCalifornia Proposition 65California Safe Drinking Water and Toxic Enforcement Act of 2016 (Proposition 65): This materialis not known to contain any chemicals currently listed as carcinogens or reproductive toxins. Formore information go to www.P65Warnings.ca.gov.US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,subd. (a))Butoxydiglycol (CAS 112-34-5)Distillates (petroleum), Hydrotreated Heavy Naphthenic (CAS 64742-52-5)International InventoriesCountry(s) or region Inventory name On inventory (yes/no)*NoAustralia Australian Inventory of Chemical Substances (AICS) NoCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) NoChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial ChemicalSubstances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) NoKorea Existing Chemicals List (ECL) NoNew Zealand New Zealand Inventory NoPhilippines Philippine Inventory of Chemicals and Chemical Substances(PICCS) NoTaiwan Taiwan Chemical Substance Inventory (TCSI) 9 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US Country(s) or region Inventory name On inventory (yes/no)*NoUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governingcountry(s).16. Other information, including date of preparation or last revision04-29-2015Issue dateRevision dateVersion #HMIS? ratings 02-28-202309Health: 3* Flammability: 2 Physical hazard: 0Health: 2 Flammability: 2 Instability: 0NFPA ratingsNFPA ratings 02 2The information provided in this Safety Data Sheet is correct to the best of our knowledge,information and belief at the date of its publication. The information given is designed only as aguidance for safe handling, use, processing, storage, transportation, disposal and release and isnot to be considered a warranty or quality specification. The information relates only to the specificmaterial designated and may not be valid for such material used in combination with any othermaterials or in any process, unless specified in the text.Disclaimer This document has undergone significant changes and should be reviewed in its entirety.Revision information 10 / 10Material name: Liquid Wrench Lubricating OilL212, L206 Version #: 09 Revision date: 02-28-2023 Issue date: 04-29-2015 SDS US