SAFETY DATA SHEET1. Identification Liquid Wrench Dry LubricantProduct identifierOther means of identification L512SDS number L512, L508Part No. 2905.12.0050Tariff code Dry LubricantRecommended use None known.Recommended restrictionsManufacturer/Importer/Supplier/Distributor informationManufacturerAddressCompany nameEmergency phone numberTelephoneWebsite2. Hazard(s) identification Category 1Flammable aerosolsPhysical hazards Category 2Skin corrosion/irritationHealth hazards Category 2Serious eye damage/eye irritation Category 1BGerm cell mutagenicity Category 1BCarcinogenicity Category 3 narcotic effectsSpecific target organ toxicity, single exposure Category 1Aspiration hazard Category 2Hazardous to the aquatic environment, acutehazardEnvironmental hazards Category 2Hazardous to the aquatic environment,long-term hazardNot classified.OSHA defined hazardsLabel elementsSignal word DangerHazard statement Extremely flammable aerosol. May be fatal if swallowed and enters airways. Causes skin irritation.Causes serious eye irritation. May cause drowsiness or dizziness. Toxic to aquatic life. Toxic toaquatic life with long lasting effects.Precautionary statementPrevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an openflame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Avoidbreathing mist/vapor. Wash thoroughly after handling. Use only outdoors or in a well-ventilatedarea. Avoid release to the environment. Wear eye protection/face protection. Wear protectivegloves. 1 / 11Material name: Liquid Wrench Dry LubricantL512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS USBlaster LLC8500 Sweet Valley Drive Valley View, Ohio 44125 - USA T(216)901-5800F (216)901-5801www.blastercorp.comChemtrec (800) 424-9300 Response If swallowed: Immediately call a poison center/doctor. Do NOT induce vomiting. If on skin: Washwith plenty of water. If inhaled: Remove person to fresh air and keep comfortable for breathing. Ifin eyes: Rinse cautiously with water for several minutes. Remove contact lenses, if present andeasy to do. Continue rinsing. Call a poison center/doctor if you feel unwell. If skin irritation occurs:Get medical advice/attention. If eye irritation persists: Get medical advice/attention. Take offcontaminated clothing and wash before reuse. Collect spillage.Storage Store in a well-ventilated place. Keep container tightly closed. Store locked up. Protect fromsunlight. Do not expose to temperatures exceeding 50?C/122?F.Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.Hazard(s) not otherwiseclassified (HNOC) Static accumulating flammable liquid can become electrostatically charged even in bonded andgrounded equipment. Sparks may ignite liquid and vapor. May cause flash fire or explosion.Supplemental information NOTE: This product is a consumer product and is labeled in accordance with the US ConsumerProduct Safety Commission regulations which take precedence over OSHA HazardCommunication labeling. The container label may not include the OSHA label elements listed inthis document. Always carefully review the entire SDS and the product label prior to use in theworkplace.3. Composition/information on ingredientsMixtures CAS number %Chemical name Common name and synonyms 67-63-0Isopropanol 40 - < 5074-98-6Propane 30 - < 40426260-76-6Heptanes (cyclic and linear) 20 - < 3064742-47-8Distillates (petroleum),Hydrotreated Light < 19002-84-0Polytetrafluoroethylene (PTFE) < 164742-88-7Solvent Naphtha (petroleum),Medium Aliph. < 1< 0.1Other components below reportable levels 10043-11-5Boron Nitride < 0.1*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.4. First-aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing. Call a poisoncenter or doctor/physician if you feel unwell.Inhalation Remove contaminated clothing. Wash with plenty of soap and water. If skin irritation occurs: Getmedical advice/attention. Wash contaminated clothing before reuse.Skin contact Immediately flush eyes with plenty of water for at least 15 minutes. Remove contact lenses, ifpresent and easy to do. Continue rinsing. Get medical attention if irritation develops and persists.Eye contact Call a physician or poison control center immediately. Rinse mouth. Do not induce vomiting. Ifvomiting occurs, keep head low so that stomach content doesn't get into the lungs.Ingestion Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,redness, swelling, and blurred vision. Skin irritation. May cause redness and pain.Most importantsymptoms/effects, acute anddelayed Provide general supportive measures and treat symptomatically. Keep victim under observation.Symptoms may be delayed.Indication of immediatemedical attention and specialtreatment needed Ensure that medical personnel are aware of the material(s) involved, and take precautions toprotect themselves.General information5. Fire-fighting measures Water fog. Alcohol resistant foam. Carbon dioxide (CO2). Dry chemical powder, carbon dioxide,sand or earth may be used for small fires only.Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishingmedia 2 / 11Material name: Liquid Wrench Dry LubricantL512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Contents under pressure. Pressurized container may explode when exposed to heat or flame. Thisproduct is a poor conductor of electricity and can become electrostatically charged. If sufficientcharge is accumulated, ignition of flammable mixtures can occur. To reduce potential for staticdischarge, use proper bonding and grounding procedures. This liquid may accumulate staticelectricity when filling properly grounded containers. Static electricity accumulation may besignificantly increased by the presence of small quantities of water or other contaminants. Materialwill float and may ignite on surface of water. During fire, gases hazardous to health may beformed.Specific hazards arising fromthe chemical Firefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, SCBA.Special protective equipmentand precautions for firefighters Move containers from fire area if you can do so without risk. Containers should be cooled withwater to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hoseholder or monitor nozzles, if possible. If not, withdraw and let fire burn out.Fire fightingequipment/instructions Use standard firefighting procedures and consider the hazards of other involved materials. Movecontainers from fire area if you can do so without risk. In the event of fire and/or explosion do notbreathe fumes.Specific methods Extremely flammable aerosol.General fire hazards6. Accidental release measuresKeep unnecessary personnel away. Keep people away from and upwind of spill/leak. Remove allpossible sources of ignition in the surrounding area. Wear appropriate protective equipment andclothing during clean-up. Avoid breathing mist/vapor. Do not touch damaged containers or spilledmaterial unless wearing appropriate protective clothing. Ventilate closed spaces before enteringthem. Use appropriate containment to avoid environmental contamination. Transfer by mechanicalmeans such as vacuum truck to a salvage tank or other suitable container for recovery or safedisposal. Local authorities should be advised if significant spillages cannot be contained. Forpersonal protection, see section 8 of the SDS.Personal precautions,protective equipment andemergency procedures Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so withoutrisk. Move the cylinder to a safe and open area if the leak is irreparable. Keep combustibles (wood,paper, oil, etc.) away from spilled material. The product is immiscible with water and will spread onthe water surface. Prevent product from entering drains. Absorb in vermiculite, dry sand or earthand place into containers. Following product recovery, flush area with water.Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly toremove residual contamination. For waste disposal, see section 13 of the SDS.Methods and materials forcontainment and cleaning up Avoid release to the environment. Inform appropriate managerial or supervisory personnel of allenvironmental releases. Prevent further leakage or spillage if safe to do so. Avoid discharge intodrains, water courses or onto the ground. Use appropriate containment to avoid environmentalcontamination.Environmental precautions7. Handling and storage Minimize fire risks from flammable and combustible materials (including combustible dust andstatic accumulating liquids) or dangerous reactions with incompatible materials. Handlingoperations that can promote accumulation of static charges include but are not limited to: mixing,filtering, pumping at high flow rates, splash filling, creating mists or sprays, tank and containerfilling, tank cleaning, sampling, gauging, switch loading, vacuum truck operations. Pressurizedcontainer: Do not pierce or burn, even after use. Do not use if spray button is missing or defective.Do not spray on a naked flame or any other incandescent material. Do not smoke while using oruntil sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, or expose containers toheat, flame, sparks, or other sources of ignition. All equipment used when handling the productmust be grounded. Do not re-use empty containers. Avoid contact with eyes, skin, and clothing.Avoid prolonged exposure. Use only in well-ventilated areas. Wear appropriate personal protectiveequipment. Wash hands thoroughly after handling. Avoid release to the environment. Observegood industrial hygiene practices.For additional information on equipment bonding and grounding, refer to the Canadian ElectricalCode in Canada, (CSA C22.1), or the American Petroleum Institute (API) Recommended Practice2003, "Protection Against Ignitions Arising out of Static, Lightning, and Stray Currents" or NationalFire Protection Association (NFPA) 77, "Recommended Practice on Static Electricity" or NationalFire Protection Association (NFPA) 70, "National Electrical Code".Precautions for safe handling 3 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Level 3 Aerosol.Store locked up. Pressurized container. Protect from sunlight and do not expose to temperaturesexceeding 50?C/122 ?F. Do not puncture, incinerate or crush. Do not handle or store near an openflame, heat or other sources of ignition. This material can accumulate static charge which maycause spark and become an ignition source. Avoid spark promoters. Ground/bond container andequipment. These alone may be insufficient to remove static electricity. Store in tightly closedcontainer. Keep out of the reach of children. Store away from incompatible materials (see Section10 of the SDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionOccupational exposure limitsThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.At this time, the other constituents have no known exposure limits.US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents TypePEL 400 mg/m3Distillates (petroleum),Hydrotreated Light (CAS64742-47-8) 100 ppmPEL 980 mg/m3Isopropanol (CAS 67-63-0) 400 ppmPEL 1800 mg/m3Propane (CAS 74-98-6) 1000 ppmPEL 400 mg/m3Solvent Naphtha(petroleum), Medium Aliph.(CAS 64742-88-7) 100 ppmUS. ACGIH Threshold Limit Values FormValueComponents TypeSTEL 400 ppmIsopropanol (CAS 67-63-0) TWA 200 ppmTWA 200 mg/m3 Non-aerosol.Solvent Naphtha(petroleum), Medium Aliph.(CAS 64742-88-7)US. NIOSH: Pocket Guide to Chemical Hazards ValueComponents TypeTWA 100 mg/m3Distillates (petroleum),Hydrotreated Light (CAS64742-47-8) STEL 1225 mg/m3Isopropanol (CAS 67-63-0) 500 ppmTWA 980 mg/m3400 ppmTWA 1800 mg/m3Propane (CAS 74-98-6) 1000 ppmBiological limit valuesACGIH Biological Exposure IndicesValueComponents Determinant Specimen Sampling Time40 mg/l Acetone Urine *Isopropanol (CAS 67-63-0)* - For sampling details, please see the source document.Exposure guidelinesUS ACGIH Threshold Limit Values: Skin designationSolvent Naphtha (petroleum), Medium Aliph. (CAS64742-88-7) Can be absorbed through the skin. 4 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Good general ventilation (typically 10 air changes per hour) should be used. Ventilation ratesshould be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,or other engineering controls to maintain airborne levels below recommended exposure limits. Ifexposure limits have not been established, maintain airborne levels to an acceptable level. Provideeyewash station and safety shower.Appropriate engineeringcontrolsIndividual protection measures, such as personal protective equipmentChemical respirator with organic vapor cartridge and full facepiece. Applicable for industrialsettings only.Eye/face protectionSkin protection Wear appropriate chemical resistant gloves. Applicable for industrial settings only.Hand protection Wear appropriate chemical resistant clothing. Applicable for industrial settings only.Other Chemical respirator with organic vapor cartridge and full facepiece. Chemical respirator withorganic vapor cartridge and full facepiece if threshold limits are exceeded. Applicable for industrialsettings only.Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards When using do not smoke. Always observe good personal hygiene measures, such as washingafter handling the material and before eating, drinking, and/or smoking. Routinely wash workclothing and protective equipment to remove contaminants.General hygieneconsiderations9. Physical and chemical propertiesMilky. LiquidAppearance Liquid.Physical state Aerosol.Form WhiteColor Mild AlcoholOdorOdor threshold Not available.pH Not available.Melting point/freezing point -196.98 ?F (-127.21 ?C) estimatedInitial boiling point and boilingrange 113.74 ?F (45.41 ?C) estimatedFlash point -104.0 ?F (-75.6 ?C) (Propane)Evaporation rate Not available.Not applicable.Flammability (solid, gas)Upper/lower flammability or explosive limitsFlammability limit - lower(%) 2.4 % estimatedFlammability limit - upper(%) 11 % estimatedExplosive limit - lower (%) 2.1 (Propane)Explosive limit - upper (%) 9.5 (Propane)Vapor pressure 950000 (Propane)Vapor density 1.56 (Propane)Relative density Not available.Solubility(ies)Solubility (water) InsolublePartition coefficient(n-octanol/water) Not available.Auto-ignition temperature 842 ?F (450 ?C) (Propane)Decomposition temperature Not available.Viscosity Not available.Other informationDensity 6.34 lbs/galNot explosive.Explosive properties 5 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Flame extension > 21 inFlammability (flash back) NoFlammability class Flammable IB estimatedHeat of combustion 34.6 kJ/gHeat of combustion (NFPA30B) 33.55 kJ/g estimatedKinematic viscosity < 20Not oxidizing.Oxidizing propertiesPercent volatile 97.8 %Specific gravity 0.76VOC 97.8 % w/w10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability No dangerous reaction known under conditions of normal use.Possibility of hazardousreactions Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Avoidtemperatures exceeding the flash point. Contact with incompatible materials.Conditions to avoid Acids. Strong oxidizing agents. Chlorine. Isocyanates.Incompatible materials No hazardous decomposition products are known.Hazardous decompositionproducts11. Toxicological informationInformation on likely routes of exposureInhalation May cause drowsiness and dizziness. Headache. Nausea, vomiting. Prolonged inhalation may beharmful.Skin contact Causes skin irritation.Eye contact Causes serious eye irritation.Ingestion Droplets of the product aspirated into the lungs through ingestion or vomiting may cause a seriouschemical pneumonia.Symptoms related to thephysical, chemical andtoxicological characteristics Aspiration may cause pulmonary edema and pneumonitis. May cause drowsiness and dizziness.Headache. Nausea, vomiting. Severe eye irritation. Symptoms may include stinging, tearing,redness, swelling, and blurred vision. Skin irritation. May cause redness and pain.Information on toxicological effectsAcute toxicity May be fatal if swallowed and enters airways. Test ResultsComponents SpeciesDistillates (petroleum), Hydrotreated Light (CAS 64742-47-8)DermalAcuteLD50 Rabbit > 2000 mg/kg, 24 HoursInhalationLC50 Rat > 0.1 mg/l, 8 HoursVaporOralLD50 Rat > 5000 mg/kgIsopropanol (CAS 67-63-0)OralAcuteLD50 Rat 4.7 g/kg 6 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Test ResultsComponents SpeciesSolvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)InhalationAcuteLC50 Rat 61 mg/l, 4 HoursCauses skin irritation.Skin corrosion/irritation Causes serious eye irritation.Serious eye damage/eyeirritationRespiratory or skin sensitizationRespiratory sensitization Not a respiratory sensitizer.This product is not expected to cause skin sensitization.Skin sensitization No data available to indicate product or any components present at greater than 0.1% aremutagenic or genotoxic.Germ cell mutagenicityCarcinogenicity Not classifiable as to carcinogenicity to humans.IARC Monographs. Overall Evaluation of CarcinogenicityPolytetrafluoroethylene (PTFE) (CAS 9002-84-0) 3 Not classifiable as to carcinogenicity to humans.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.US. National Toxicology Program (NTP) Report on CarcinogensNot listed. This product is not expected to cause reproductive or developmental effects.Reproductive toxicitySpecific target organ toxicity -single exposure May cause drowsiness and dizziness.Specific target organ toxicity -repeated exposure Not classified.Aspiration hazard May be fatal if swallowed and enters airways.Chronic effects Prolonged inhalation may be harmful.12. Ecological information Toxic to aquatic life with long lasting effects.EcotoxicityComponents Test ResultsSpeciesDistillates (petroleum), Hydrotreated Light (CAS 64742-47-8)Aquatic EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex)LC50Fish 2.9 mg/l, 96 hoursRainbow trout,donaldson trout(Oncorhynchus mykiss)Isopropanol (CAS 67-63-0)Aquatic LC50Fish > 1400 mg/l, 96 hoursBluegill (Lepomis macrochirus)Solvent Naphtha (petroleum), Medium Aliph. (CAS 64742-88-7)Aquatic EC50Crustacea 2.7 - 5.1 mg/l, 48 hoursWater flea (Daphnia pulex)LC50Fish 8.8 mg/l, 96 hoursRainbow trout,donaldson trout(Oncorhynchus mykiss) 8.8 mg/l, 96 hoursNo data is available on the degradability of any ingredients in the mixture.Persistence and degradabilityBioaccumulative potentialPartition coefficient n-octanol / water (log Kow)Isopropanol 0.05Propane 2.36No data available.Mobility in soilOther adverse effects The product contains volatile organic compounds which have a photochemical ozone creationpotential. 7 / 11Material name: Liquid Wrench Dry Lubricant 512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US 13. Disposal considerationsCollect and reclaim or dispose in sealed containers at licensed waste disposal site. Contentsunder pressure. Do not puncture, incinerate or crush. Incinerate the material under controlledconditions in an approved incinerator. Do not allow this material to drain into sewers/watersupplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Ifdiscarded, this product is considered a RCRA ignitable waste, D001. Dispose ofcontents/container in accordance with local/regional/national/international regulations.Disposal instructions Dispose in accordance with all applicable regulations.Local disposal regulations D001: Waste Flammable material with a flash point <140 FThe waste code should be assigned in discussion between the user, the producer and the wastedisposal company.Hazardous waste code Dispose of in accordance with local regulations. Empty containers or liners may retain someproduct residues. This material and its container must be disposed of in a safe manner (see:Disposal instructions).Waste from residues / unusedproducts Since emptied containers may retain product residue, follow label warnings even after container isemptied. Empty containers should be taken to an approved waste handling site for recycling ordisposal. Do not re-use empty containers.Contaminated packaging14. Transport informationDOT UN1950UN number Aerosols, flammable, (each not exceeding 1 L capacity), Limited QuantityUN proper shipping name 2.1ClassTransport hazard class(es) -Subsidiary risk 2.1Label(s) Not available.Packing group Read safety instructions, SDS and emergency procedures before handling.Special precautions for user N82Special provisions 306Packaging exceptions NonePackaging non bulk NonePackaging bulkIATA UN1950UN number Aerosol, flammable, Limited QuantityUN proper shipping name 2.1ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group No.Environmental hazards 9LERG Code Read safety instructions, SDS and emergency procedures before handling.Special precautions for user Allowed with restrictions.Passenger and cargoaircraftOther information Allowed with restrictions.Cargo aircraft onlyIMDG UN1950UN number AEROSOLS, MARINE POLLUTANT (Heptanes), Limited QuantityUN proper shipping name 2ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group YesMarine pollutantEnvironmental hazards F-D, S-UEmS Read safety instructions, SDS and emergency procedures before handling.Special precautions for userHeptanes 8 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Not established.Transport in bulk according toAnnex II of MARPOL 73/78 andthe IBC CodeDOT; IMDGIATAMarine pollutant15. Regulatory informationThis product is a "Hazardous Chemical" as defined by the OSHA Hazard CommunicationStandard, 29 CFR 1910.1200.US federal regulationsTSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)Not regulated.TSCA Chemical Action Plans, Chemicals of ConcernPolytetrafluoroethylene (PTFE) (CAS 9002-84-0) Long-Chain Perfluorinated Chemicals (PFCs) Action PlanCERCLA Hazardous Substance List (40 CFR 302.4)Isopropanol (CAS 67-63-0) Listed.Propane (CAS 74-98-6) Listed.SARA 304 Emergency release notificationNot regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.SARA 302 Extremely hazardous substanceSuperfund Amendments and Reauthorization Act of 1986 (SARA)Not listed.SARA 313 (TRI reporting)Chemical name % by wt.CAS numberIsopropanol 40 - < 5067-63-0 9 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) ListNot regulated.Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)Propane (CAS 74-98-6) Not regulated.Safe Drinking Water Act(SDWA)FEMA Priority Substances Respiratory Health and Safety in the Flavor Manufacturing WorkplaceIsopropanol (CAS 67-63-0) Low priorityUS state regulationsCalifornia Proposition 65California Safe Drinking Water and Toxic Enforcement Act of 2016 (Proposition 65): This materialis not known to contain any chemicals currently listed as carcinogens or reproductive toxins. Formore information go to www.P65Warnings.ca.gov.US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3,subd. (a))Isopropanol (CAS 67-63-0)International InventoriesCountry(s) or region Inventory name On inventory (yes/no)*NoAustralia Australian Inventory of Chemical Substances (AICS) YesCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) NoChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial ChemicalSubstances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) YesKorea Existing Chemicals List (ECL) NoNew Zealand New Zealand Inventory YesPhilippines Philippine Inventory of Chemicals and Chemical Substances(PICCS) YesTaiwan Taiwan Chemical Substance Inventory (TCSI) YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governingcountry(s).16. Other information, including date of preparation or last revision06-01-2015Issue dateRevision dateVersion #HMIS? ratings 02-28-202310Health: 2 Flammability: 4 Physical hazard: 0Health: 2 Flammability: 4 Instability: 0NFPA ratingsNFPA ratings 02 4 10 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US The information provided in this Safety Data Sheet is correct to the best of our knowledge,information and belief at the date of its publication. The information given is designed only as aguidance for safe handling, use, processing, storage, transportation, disposal and release and isnot to be considered a warranty or quality specification. The information relates only to the specificmaterial designated and may not be valid for such material used in combination with any othermaterials or in any process, unless specified in the text.Disclaimer This document has undergone significant changes and should be reviewed in its entirety.Revision information 11 / 11Material name: Liquid Wrench Dry Lubricant L512, L506 Version #: 10 Revision date: 02-28-2023 Issue date: 06-01-2015 SDS US