SAFETY DATA SHEET1. Identification Tite Seal Instant Tire RepairProduct identifierOther means of identification M11 seriesSDS number M1108, M1114, M1118, M1128Part No. 3506.91.0000Tariff code Tire RepairRecommended use None known.Recommended restrictionsManufacturer/Importer/Supplier/Distributor informationManufacturerAddressCompany nameWebsiteTelephoneEmergency phone numberE-mail2. Hazard(s) identification Category 2Flammable aerosolsPhysical hazards Category 2Specific target organ toxicity, repeatedexposureHealth hazards Not classified.Environmental hazards Not classified.OSHA defined hazardsLabel elementsSignal word WarningHazard statement Pressurized container: May burst if heated. May cause damage to organs through prolonged orrepeated exposure.Precautionary statementPrevention Keep away from heat/sparks/open flames/hot surfaces. - No smoking. Do not spray on an openflame or other ignition source. Pressurized container: Do not pierce or burn, even after use. Donot breathe mist or vapor.Response Get medical advice/attention if you feel unwell.Storage Protect from sunlight. Do not expose to temperatures exceeding 50?C/122?F.Disposal Dispose of contents/container in accordance with local/regional/national/international regulations.Hazard(s) not otherwiseclassified (HNOC) None known.Supplemental information NOTE: GHS Category 3 Non-flammable aerosol (version 7 - July 2017).NOTE: This product is a consumer product and is labeled in accordance with the US ConsumerProduct Safety Commission regulations which take precedence over OSHA HazardCommunication labeling. The container label may not include the OSHA label elements listed inthis document. Always carefully review the entire SDS and the product label prior to use in theworkplace. 1 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02/23/2023 Issue date: 07-14-2016 SDS USBlaster LLC8500 Sweet Valley Drive Valley View, Ohio 44125 - USA T(216)901-5800F (216)901-5801www.blastercorp.comChemtrec (800) 424-9300 3. Composition/information on ingredientsMixtures CAS number %Chemical name Common name and synonyms 7732-18-5Water 60 - < 7029118-24-9Trans-1,3,3,3-Tetrafluoroprop-1-ene 20 - < 30MixtureAcrylic Polymer Dispersion 1 - < 3107-21-1Ethylene Glycol 1 - < 31336-21-6Ammonium Hydroxide < 0.2MixtureCellulose < 0.211138-66-2Xanthan Gum < 0.277-92-9Citric Acid < 0.11 - < 3Other components below reportable levels 107-22-2Glyoxal < 0.1*Designates that a specific chemical identity and/or percentage of composition has been withheld as a trade secret.4. First-aid measures If symptoms develop move victim to fresh air. Get medical attention if symptoms persist.Inhalation Wash off with soap and water. Get medical attention if irritation develops and persists.Skin contact Rinse with water. Get medical attention if irritation develops and persists.Eye contact In the unlikely event of swallowing contact a physician or poison control center.Ingestion Prolonged exposure may cause chronic effects.Most importantsymptoms/effects, acute anddelayed Provide general supportive measures and treat symptomatically. Keep victim under observation.Symptoms may be delayed.Indication of immediatemedical attention and specialtreatment needed If you feel unwell, seek medical advice (show the label where possible). Ensure that medicalpersonnel are aware of the material(s) involved, and take precautions to protect themselves.General information5. Fire-fighting measures Water fog. Foam. Dry chemical powder. Carbon dioxide (CO2).Suitable extinguishing media Do not use water jet as an extinguisher, as this will spread the fire.Unsuitable extinguishingmedia Contents under pressure. Pressurized container may explode when exposed to heat or flame.During fire, gases hazardous to health may be formed.Specific hazards arising fromthe chemical Firefighters must use standard protective equipment including flame retardant coat, helmet withface shield, gloves, rubber boots, and in enclosed spaces, SCBA.Special protective equipmentand precautions for firefighters Move containers from fire area if you can do so without risk. Containers should be cooled withwater to prevent vapor pressure build up. For massive fire in cargo area, use unmanned hoseholder or monitor nozzles, if possible. If not, withdraw and let fire burn out.Fire fightingequipment/instructions Use standard firefighting procedures and consider the hazards of other involved materials. Movecontainers from fire area if you can do so without risk. In the event of fire and/or explosion do notbreathe fumes.Specific methods Flammable aerosol. Contents under pressure.General fire hazards6. Accidental release measuresKeep unnecessary personnel away. Keep people away from and upwind of spill/leak. Wearappropriate protective equipment and clothing during clean-up. Do not breathe mist or vapor. Donot touch damaged containers or spilled material unless wearing appropriate protective clothing.Ventilate closed spaces before entering them. Local authorities should be advised if significantspillages cannot be contained. For personal protection, see section 8 of the SDS.Personal precautions,protective equipment andemergency procedures 2 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02/23/2023 Issue date: 07-14-2016 SDS US Refer to attached safety data sheets and/or instructions for use. Stop leak if you can do so withoutrisk. Move the cylinder to a safe and open area if the leak is irreparable. Keep combustibles (wood,paper, oil, etc.) away from spilled material. Absorb in vermiculite, dry sand or earth and place intocontainers. Following product recovery, flush area with water.Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly toremove residual contamination. For waste disposal, see section 13 of the SDS.Methods and materials forcontainment and cleaning up Avoid discharge into drains, water courses or onto the ground.Environmental precautions7. Handling and storage Pressurized container: Do not pierce or burn, even after use. Do not use if spray button is missingor defective. Do not spray on a naked flame or any other incandescent material. Do not smokewhile using or until sprayed surface is thoroughly dry. Do not cut, weld, solder, drill, grind, orexpose containers to heat, flame, sparks, or other sources of ignition. All equipment used whenhandling the product must be grounded. Do not re-use empty containers. Avoid prolongedexposure. Use only in well-ventilated areas. Wear appropriate personal protective equipment.Observe good industrial hygiene practices.Precautions for safe handling Level 1 Aerosol.Pressurized container. Protect from sunlight and do not expose to temperatures exceeding50?C/122 ?F. Do not puncture, incinerate or crush. Do not handle or store near an open flame,heat or other sources of ignition. This material can accumulate static charge which may causespark and become an ignition source. Store in tightly closed container. Keep out of the reach ofchildren. Store away from incompatible materials (see Section 10 of the SDS).Conditions for safe storage,including any incompatibilities8. Exposure controls/personal protectionOccupational exposure limitsThe following constituents are the only constituents of the product which have a PEL, TLV or other recommended exposure limit.At this time, the other constituents have no known exposure limits.US. OSHA Table Z-1 Limits for Air Contaminants (29 CFR 1910.1000) ValueComponents TypePEL 35 mg/m3Ammonium Hydroxide (CAS1336-21-6) 50 ppmUS. ACGIH Threshold Limit Values FormValueComponents TypeSTEL 35 ppmAmmonium Hydroxide (CAS1336-21-6) TWA 25 ppmSTEL 10 mg/m3 Aerosol, inhalable.Ethylene Glycol (CAS107-21-1) 50 ppm Vapor fractionTWA 25 ppm Vapor fractionTWA 0.1 mg/m3 Inhalable fraction andvapor.Glyoxal (CAS 107-22-2)US. NIOSH: Pocket Guide to Chemical Hazards ValueComponents TypeSTEL 27 mg/m3Ammonium Hydroxide (CAS1336-21-6) 35 ppmTWA 18 mg/m325 ppmUS. Workplace Environmental Exposure Level (WEEL) Guides FormValueComponents TypeTWA 0.1 mg/m3 Inhalable fraction andvapor.Glyoxal (CAS 107-22-2) 0.042 ppm Inhalable fraction andvapor. 3 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US US. Workplace Environmental Exposure Level (WEEL) Guides FormValueComponents TypeTWA 800 ppmTrans-1,3,3,3-Tetrafluoroprop-1-ene (CAS 29118-24-9) No biological exposure limits noted for the ingredient(s).Biological limit values Good general ventilation (typically 10 air changes per hour) should be used. Ventilation ratesshould be matched to conditions. If applicable, use process enclosures, local exhaust ventilation,or other engineering controls to maintain airborne levels below recommended exposure limits. Ifexposure limits have not been established, maintain airborne levels to an acceptable level.Appropriate engineeringcontrolsIndividual protection measures, such as personal protective equipmentWear safety glasses with side shields (or goggles) or a face shield. Chemical respirator withorganic vapor cartridge and full facepiece. Applicable for industrial settings only.Eye/face protectionSkin protection Wear appropriate chemical resistant gloves. Applicable for industrial settings only.Hand protection Wear appropriate chemical resistant clothing. Use of an impervious apron is recommended.Applicable for industrial settings only.Other Chemical respirator with organic vapor cartridge and full facepiece. Chemical respirator withorganic vapor cartridge and full facepiece if threshold limits are exceeded. Applicable for industrialsettings only.Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards When using do not smoke. Always observe good personal hygiene measures, such as washingafter handling the material and before eating, drinking, and/or smoking. Routinely wash workclothing and protective equipment to remove contaminants.General hygieneconsiderations9. Physical and chemical propertiesOpaque LiquidAppearance Liquid.Physical state Aerosol.Form Milky. WhiteColor AmmoniaOdorOdor threshold Not available.pH 9.3 - 9.8Melting point/freezing point 29 ?F (-1.67 ?C) estimatedInitial boiling point and boilingrange 212 ?F (100 ?C)Flash point No Flash PointEvaporation rate Not available.Not applicable.Flammability (solid, gas)Upper/lower flammability or explosive limitsFlammability limit - lower(%) Not available.Flammability limit - upper(%) Not available.Explosive limit - lower (%) Not available.Explosive limit - upper (%) Not available.Vapor pressure 2078.98424 hPa estimatedVapor density Not available.Relative density Not available.Solubility(ies)Solubility (water) Not available.Partition coefficient(n-octanol/water) Not available.Auto-ignition temperature 694.4 ?F (368 ?C) estimated 4 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US Decomposition temperature Not available.Viscosity Not available.Other informationDensity 8.34 lbs/gal ConcentrateNot explosive.Explosive propertiesFlammability (flash back) NoneHeat of combustion (NFPA30B) 0.5 kJ/gNot oxidizing.Oxidizing propertiesPercent volatile > 95 %Specific gravity 1VOC 0 % w/w10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability Hazardous polymerization does not occur.Possibility of hazardousreactions Keep away from heat, hot surfaces, sparks, open flames and other ignition sources. Contact withincompatible materials.Conditions to avoid Strong oxidizing agents.Incompatible materials No hazardous decomposition products are known.Hazardous decompositionproducts11. Toxicological informationInformation on likely routes of exposureInhalation Prolonged inhalation may be harmful.Skin contact No adverse effects due to skin contact are expected.Eye contact Direct contact with eyes may cause temporary irritation.Ingestion Expected to be a low ingestion hazard.Symptoms related to thephysical, chemical andtoxicological characteristics Direct contact with eyes may cause temporary irritation.Information on toxicological effectsAcute toxicity Not known. Test ResultsComponents SpeciesAmmonium Hydroxide (CAS 1336-21-6)OralAcuteLD50 Rat 350 mg/kgCitric Acid (CAS 77-92-9)OralAcuteLD50 Rat 6730 mg/kgEthylene Glycol (CAS 107-21-1)DermalAcuteLD50 Rabbit 9530 mg/kgOralLD50 Rat 5.89 g/kg 5 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US Test ResultsComponents SpeciesGlyoxal (CAS 107-22-2)DermalAcuteLD50 Rat > 800 mg/kg, 24 HoursInhalationLC50 Rat > 1.3 mg/l, 4 Hours2.47 mg/l, 4 HoursOralLD50 Rat 762 mg/kgProlonged skin contact may cause temporary irritation.Skin corrosion/irritation Direct contact with eyes may cause temporary irritation.Serious eye damage/eyeirritationRespiratory or skin sensitizationACGIH sensitizationGLYOXAL, INHALABLE FRACTION AND VAPOR (CAS107-22-2) Dermal sensitizationRespiratory sensitization Not a respiratory sensitizer.This product is not expected to cause skin sensitization.Skin sensitization No data available to indicate product or any components present at greater than 0.1% aremutagenic or genotoxic.Germ cell mutagenicityCarcinogenicity Not classifiable as to carcinogenicity to humans.IARC Monographs. Overall Evaluation of CarcinogenicityNot listed.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.US. National Toxicology Program (NTP) Report on CarcinogensNot listed. This product is not expected to cause reproductive or developmental effects.Reproductive toxicitySpecific target organ toxicity -single exposure Not classified.Specific target organ toxicity -repeated exposure May cause damage to organs through prolonged or repeated exposure.Aspiration hazard Not an aspiration hazard.Chronic effects May cause damage to organs through prolonged or repeated exposure. Prolonged inhalation maybe harmful.12. Ecological information The product is not classified as environmentally hazardous. However, this does not exclude thepossibility that large or frequent spills can have a harmful or damaging effect on the environment.EcotoxicityComponents Test ResultsSpeciesAmmonium Hydroxide (CAS 1336-21-6)Aquatic LC50Fish 15 mg/l, 96 hoursWestern mosquitofish (Gambusia affinis)Ethylene Glycol (CAS 107-21-1)Aquatic LC50Fish 8050 mg/l, 96 hoursFathead minnow (Pimephales promelas)Glyoxal (CAS 107-22-2)Aquatic LC50Fish 215 mg/l, 96 hoursFathead minnow (Pimephales promelas) 6 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US Components Test ResultsSpeciesXanthan Gum (CAS 11138-66-2)Aquatic LC50Fish 320 - 560 mg/l, 96 hoursRainbow trout,donaldson trout(Oncorhynchus mykiss)No data is available on the degradability of any ingredients in the mixture.Persistence and degradabilityBioaccumulative potentialPartition coefficient n-octanol / water (log Kow)Ethylene Glycol -1.36No data available.Mobility in soilOther adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creationpotential, endocrine disruption, global warming potential) are expected from this component.13. Disposal considerationsCollect and reclaim or dispose in sealed containers at licensed waste disposal site. Contentsunder pressure. Do not puncture, incinerate or crush. Dispose of contents/container in accordancewith local/regional/national/international regulations.Disposal instructions Dispose in accordance with all applicable regulations.Local disposal regulations The waste code should be assigned in discussion between the user, the producer and the wastedisposal company.Hazardous waste code Dispose of in accordance with local regulations. Empty containers or liners may retain someproduct residues. This material and its container must be disposed of in a safe manner (see:Disposal instructions).Waste from residues / unusedproducts Since emptied containers may retain product residue, follow label warnings even after container isemptied. Empty containers should be taken to an approved waste handling site for recycling ordisposal. Do not re-use empty containers.Contaminated packaging14. Transport informationDOT UN1950UN number Aerosols, non-flammable, Limited QuantityUN proper shipping name 2.2ClassTransport hazard class(es) -Subsidiary risk NoneLabel(s) Not available.Packing group NoMarine pollutantEnvironmental hazards Read safety instructions, SDS and emergency procedures before handling.Special precautions for user 306Packaging exceptions NonePackaging non bulk NonePackaging bulkIATA UN1950UN number Aerosols, non flammable, Limited QuantityUN proper shipping name 2.2ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group NoEnvironmental hazards Read safety instructions, SDS and emergency procedures before handling.Special precautions for userIMDG UN1950UN number Aerosols, Limited QuantityUN proper shipping name 2.2ClassTransport hazard class(es) -Subsidiary risk Not available.Packing group 7 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US NoMarine pollutantEnvironmental hazards F-D, S-UEmS Read safety instructions, SDS and emergency procedures before handling.Special precautions for user Not established.Transport in bulk according toAnnex II of MARPOL 73/78 andthe IBC CodeDOT; IMDGIATA15. Regulatory informationThis product is a "Hazardous Chemical" as defined by the OSHA Hazard CommunicationStandard, 29 CFR 1910.1200.US federal regulationsTSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D)Not regulated.CERCLA Hazardous Substance List (40 CFR 302.4)Ammonium Hydroxide (CAS 1336-21-6) Listed.Ethylene Glycol (CAS 107-21-1) Listed.SARA 304 Emergency release notificationNot regulated.OSHA Specifically Regulated Substances (29 CFR 1910.1001-1052)Not regulated.SARA 302 Extremely hazardous substanceSuperfund Amendments and Reauthorization Act of 1986 (SARA)Not listed. No (Exempt)SARA 311/312 HazardouschemicalSARA 313 (TRI reporting)Chemical name % by wt.CAS numberEthylene Glycol 1 - < 3107-21-1Other federal regulationsClean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) ListEthylene Glycol (CAS 107-21-1)Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130)Not regulated. Not regulated.Safe Drinking Water Act(SDWA) 8 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 09 Revision date: 02-23-2023 Issue date: 07-14-2016 SDS US US state regulationsCalifornia Proposition 65 California Safe Drinking Water and Toxic Enforcement Act of 2016 (Proposition 65): This materialis not known to contain any chemicals currently listed as carcinogens or reproductive toxins.For more information go to www.P65Warnings.ca.gov.WARNING:International InventoriesCountry(s) or region Inventory name On inventory (yes/no)*NoAustralia Australian Inventory of Chemical Substances (AICS) NoCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) NoChina Inventory of Existing Chemical Substances in China (IECSC) NoEurope European Inventory of Existing Commercial ChemicalSubstances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) NoKorea Existing Chemicals List (ECL) NoNew Zealand New Zealand Inventory NoPhilippines Philippine Inventory of Chemicals and Chemical Substances(PICCS) NoTaiwan Taiwan Chemical Substance Inventory (TCSI) NoUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory*A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s)A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governingcountry(s).16. Other information, including date of preparation or last revision07-14-2016Issue dateRevision dateVersion #HMIS? ratings 02-23-202309Health: 2Flammability: 0Physical hazard: 0Health: 2Flammability: 0Instability: 0NFPA ratingsNFPA ratings 02 0The information provided in this Safety Data Sheet is correct to the best of our knowledge,information and belief at the date of its publication. The information given is designed only as aguidance for safe handling, use, processing, storage, transportation, disposal and release and isnot to be considered a warranty or quality specification. The information relates only to the specificmaterial designated and may not be valid for such material used in combination with any othermaterials or in any process, unless specified in the text.Disclaimer Physical & Chemical Properties: Multiple PropertiesRevision information 9 / 9Material name: Tite Seal Instant Tire RepairM1108, M1114, M1118, M1128 Version #: 08 Revision date: 03-26-2020 Issue date: 07-14-2016 SDS US