SAFETY DATA SHEET 1. Identification Honing & Cutting OilProduct identifier Other means of identification SL2523Product code Honing and cutting oilRecommended use None known.Recommended restrictions Manufacturer/Importer/Supplier/Distributor information Manufactured or sold by: Company name CRC Industries, Inc. Address 885 Louis Dr. Warminster, PA 18974 US Telephone General Information 215-674-4300 Technical Assistance 800-521-3168 Customer Service 800-272-4620 24-Hour Emergency 800-424-9300 (US) (CHEMTREC) 703-527-3887 (International) Website www.crcindustries.com 2. Hazard(s) identification Not classified.Physical hazards Category 1Sensitization, skinHealth hazards Not classified.Environmental hazards Not classified.OSHA defined hazards Label elements Signal word Warning Hazard statement May cause an allergic skin reaction. Precautionary statement Prevention Avoid breathing vapors. Contaminated work clothing must not be allowed out of the workplace. Wear protective gloves. Response If on skin: Wash with plenty of water. If skin irritation or rash occurs: Get medical attention. Wash contaminated clothing before reuse. Storage Store away from incompatible materials. Disposal Dispose of contents/container in accordance with local/regional/national regulations. Hazard(s) not otherwise classified (HNOC) None known. 3. Composition/information on ingredients Mixtures CAS number %Common name and synonymsChemical name 64742-54-7 80 - 90Distillates (petroleum), hydrotreated heavy paraffinic 1 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US CAS number %Common name and synonymsChemical name 61789-86-4 1 - 5Sulfonic acids, petroleum, calcium salts Specific chemical identity and/or percentage of composition has been withheld as a trade secret. 4. First-aid measures Remove victim to fresh air and keep at rest in a position comfortable for breathing. If breathing is difficult, trained personnel should give oxygen. Do not use mouth-to-mouth method if victim inhaled the substance. Call a physician if symptoms develop or persist. Inhalation Remove contaminated clothing immediately and wash skin with soap and water. In case of eczema or other skin disorders: Seek medical attention and take along these instructions. Wash contaminated clothing before reuse. Skin contact Immediately flush eyes with plenty of water for at least 15 minutes. Continue rinsing. Get medical attention if irritation develops and persists. Eye contact Rinse mouth. Drink 1 or 2 glasses of water. Never give anything by mouth to a victim who is unconscious or is having convulsions. Do not induce vomiting without advice from poison control center. If vomiting occurs, keep head low so that stomach content doesn't get into the lungs. If ingestion of a large amount does occur, call a poison control center immediately. Ingestion Irritation of eyes and mucous membranes. May cause an allergic skin reaction. Rash. Skin irritation. Dermatitis. Most important symptoms/effects, acute and delayed Provide general supportive measures and treat symptomatically. Keep victim under observation. Symptoms may be delayed. Indication of immediate medical attention and special treatment needed Ensure that medical personnel are aware of the material(s) involved, and take precautions to protect themselves. Wash contaminated clothing before reuse. General information 5. Fire-fighting measures Use fire-extinguishing media appropriate for surrounding materials.Suitable extinguishing media None known.Unsuitable extinguishing media During fire, gases hazardous to health may be formed.Specific hazards arising from the chemical Firefighters must use standard protective equipment including flame retardant coat, helmet with face shield, gloves, rubber boots, and in enclosed spaces, SCBA. Special protective equipment and precautions for firefighters No unusual fire or explosion hazards noted.General fire hazards 6. Accidental release measures Keep unnecessary personnel away. Keep people away from and upwind of spill/leak. Keep out of low areas. Do not touch damaged containers or spilled material unless wearing appropriate protective clothing. For personal protection, see section 8 of the SDS. Personal precautions, protective equipment and emergency procedures The product is immiscible with water and will spread on the water surface. Large Spills: Stop the flow of material, if this is without risk. Dike the spilled material, where this is possible. Cover with plastic sheet to prevent spreading. Absorb in vermiculite, dry sand or earth and place into containers. Following product recovery, flush area with water. Small Spills: Wipe up with absorbent material (e.g. cloth, fleece). Clean surface thoroughly to remove residual contamination. Never return spills to original containers for re-use. For waste disposal, see section 13 of the SDS. Prevent entry into waterways, sewer, basements or confined areas. Methods and materials for containment and cleaning up Avoid discharge into drains, water courses or onto the ground.Environmental precautions 7. Handling and storage Avoid contact with eyes, skin, and clothing. Provide adequate ventilation. Wear appropriate personal protective equipment. Avoid release to the environment. Observe good industrial hygiene practices. Use care in handling/storage. For product usage instructions, please see the product label. Precautions for safe handling Keep container tightly closed. Store away from incompatible materials (see Section 10 of the SDS). Store in a cool, dry place out of direct sunlight. Store in a well-ventilated place. Conditions for safe storage, including any incompatibilities 2 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US 8. Exposure controls/personal protection Occupational exposure limits U.S. - OSHA ValueComponents Type TWA 5 mg/m3Distillates (petroleum), hydrotreated heavy paraffinic (CAS 64742-54-7) ACGIH ValueComponents FormType TWA 5 mg/m3 Inhalable fractionDistillates (petroleum), hydrotreated heavy paraffinic (CAS 64742-54-7) US. ACGIH Threshold Limit Values ValueComponents FormType TWA 5 mg/m3 Inhalable fraction.Distillates (petroleum), hydrotreated heavy paraffinic (CAS 64742-54-7) U.S. - NIOSH ValueComponents FormType STEL 10 mg/m3 MistDistillates (petroleum), hydrotreated heavy paraffinic (CAS 64742-54-7) TWA 5 mg/m3 Mist No biological exposure limits noted for the ingredient(s).Biological limit values Good general ventilation (typically 10 air changes per hour) should be used. Ventilation rates should be matched to conditions. If applicable, use process enclosures, local exhaust ventilation, or other engineering controls to maintain airborne levels below recommended exposure limits. If exposure limits have not been established, maintain airborne levels to an acceptable level. Appropriate engineering controls Individual protection measures, such as personal protective equipment Wear safety glasses with side shields (or goggles).Eye/face protection Skin protection Wear protective gloves such as: Nitrile. Rubber.Hand protection Wear appropriate chemical resistant clothing.Other If engineering controls are not feasible or if exposure exceeds the applicable exposure limits, use a NIOSH-approved cartridge respirator with an organic vapor cartridge. Use a self-contained breathing apparatus in confined spaces and for emergencies. Air monitoring is needed to determine actual employee exposure levels. Respiratory protection Wear appropriate thermal protective clothing, when necessary.Thermal hazards Always observe good personal hygiene measures, such as washing after handling the material and before eating, drinking, and/or smoking. Routinely wash work clothing and protective equipment to remove contaminants. Contaminated work clothing should not be allowed out of the workplace. General hygiene considerations 9. Physical and chemical properties Appearance Liquid.Physical state Grease.Form Red.Color Sulphurous. Mild petroleum.Odor Odor threshold Not available. pH Not available. Melting point/freezing point Not available. Initial boiling point and boiling range 599 ?F (315 ?C) Flash point 378 ?F (192.2 ?C) Pensky-Martens Closed Cup 3 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US Evaporation rate Slow. Not available.Flammability (solid, gas) Upper/lower flammability or explosive limits Flammability limit - lower (%) Not available. Flammability limit - upper (%) Not available. Vapor pressure Not available. Vapor density Not available. Relative density 0.89 Solubility (water) Insoluble. Partition coefficient (n-octanol/water) Not available. Auto-ignition temperature Not available. Decomposition temperature Not available. Viscosity (kinematic) 26.7 mm?/s Viscosity temperature 104 ?F (40 ?C) Percent volatile 85 % estimated 10. Stability and reactivity The product is stable and non-reactive under normal conditions of use, storage and transport.Reactivity Material is stable under normal conditions.Chemical stability No dangerous reaction known under conditions of normal use.Possibility of hazardous reactions Contact with incompatible materials.Conditions to avoid Strong oxidizing agents.Incompatible materials Carbon oxides. Metal oxides.Hazardous decomposition products 11. Toxicological information Information on likely routes of exposure Inhalation Health injuries are not known or expected under normal use. Skin contact May cause an allergic skin reaction. Eye contact Direct contact with eyes may cause temporary irritation. Ingestion Expected to be a low ingestion hazard. Symptoms related to the physical, chemical and toxicological characteristics Rash. Irritation of eyes and mucous membranes. Skin irritation. May cause an allergic skin reaction. Dermatitis. Information on toxicological effects Acute toxicity May cause an allergic skin reaction. Test ResultsProduct Species Honing & Cutting Oil Dermal Acute LD50 Rabbit 5882 mg/kg estimated Oral * Estimates for product may be based on additional component data not shown. LD50 Rat 17647 mg/kg estimated Prolonged skin contact may cause temporary irritation.Skin corrosion/irritation Direct contact with eyes may cause temporary irritation.Serious eye damage/eye irritation Respiratory sensitization Not a respiratory sensitizer. 4 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US May cause an allergic skin reaction.Skin sensitization No data available to indicate product or any components present at greater than 0.1% are mutagenic or genotoxic. Germ cell mutagenicity Carcinogenicity This product is not considered to be a carcinogen by IARC, ACGIH, NTP, or OSHA. IARC Monographs. Overall Evaluation of Carcinogenicity Not available. US. National Toxicology Program (NTP) Report on Carcinogens Not available. This product is not expected to cause reproductive or developmental effects.Reproductive toxicity Specific target organ toxicity - single exposure Not classified. Specific target organ toxicity - repeated exposure Not classified. Aspiration hazard Not classified. Chronic effects Prolonged exposure may cause chronic effects. 12. Ecological information There is insufficient information to determine the scope of the environmental effects this material may cause. Ecotoxicity No data is available on the degradability of this product.Persistence and degradability No data available.Bioaccumulative potential No data available.Mobility in soil Other adverse effects No other adverse environmental effects (e.g. ozone depletion, photochemical ozone creation potential, endocrine disruption, global warming potential) are expected from this component. 13. Disposal considerations This product is not a RCRA hazardous waste (See 40 CFR Part 261.20 ? 261.33). Empty containers may be recycled. Collect and reclaim or dispose in sealed containers at licensed waste disposal site. Do not allow this material to drain into sewers/water supplies. Do not contaminate ponds, waterways or ditches with chemical or used container. Dispose in accordance with all applicable regulations. Disposal of waste from residues / unused products Not regulated.Hazardous waste code Empty containers should be taken to an approved waste handling site for recycling or disposal. Since emptied containers may retain product residue, follow label warnings even after container is emptied. Contaminated packaging 14. Transport information DOT Not regulated as dangerous goods. IATA Not regulated as dangerous goods. IMDG Not regulated as dangerous goods. 15. Regulatory information This product is a "Hazardous Chemical" as defined by the OSHA Hazard Communication Standard, 29 CFR 1910.1200. All components are on the U.S. EPA TSCA Inventory List. US federal regulations TSCA Section 12(b) Export Notification (40 CFR 707, Subpt. D) Not regulated. US. OSHA Specifically Regulated Substances (29 CFR 1910.1001-1050) Not listed. SARA 304 Emergency release notification Not regulated. US EPCRA (SARA Title III) Section 313 - Toxic Chemical: Listed substance Not listed. 5 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US CERCLA Hazardous Substance List (40 CFR 302.4) Not listed. CERCLA Hazardous Substances: Reportable quantity Not listed. Spills or releases resulting in the loss of any ingredient at or above its RQ require immediate notification to the National Response Center (800-424-8802) and to your Local Emergency Planning Committee. Clean Air Act (CAA) Section 112 Hazardous Air Pollutants (HAPs) List Not regulated. Clean Air Act (CAA) Section 112(r) Accidental Release Prevention (40 CFR 68.130) Not regulated. Not regulated.Safe Drinking Water Act (SDWA) Not regulated.Food and Drug Administration (FDA) Superfund Amendments and Reauthorization Act of 1986 (SARA) Immediate Hazard - Yes Delayed Hazard - No Fire Hazard - No Pressure Hazard - No Reactivity Hazard - No Section 311/312 Hazard categories NoSARA 302 Extremely hazardous substance US state regulations US. California. Candidate Chemicals List. Safer Consumer Products Regulations (Cal. Code Regs, tit. 22, 69502.3, subd. (a)) Distillates (petroleum), hydrotreated heavy paraffinic (CAS 64742-54-7) US. Massachusetts RTK - Substance List None. US. California Controlled Substances. CA Department of Justice (California Health and Safety Code Section 11100) Not listed. US. Rhode Island RTK None. US. New Jersey Worker and Community Right-to-Know Act Not listed. US. Pennsylvania Worker and Community Right-to-Know Law Not listed. US. California Proposition 65 California Safe Drinking Water and Toxic Enforcement Act of 1986 (Proposition 65): This material is not known to contain any chemicals currently listed as carcinogens or reproductive toxins. Volatile organic compounds (VOC) regulations EPA VOC content (40 CFR 51.100(s)) Not determined Not regulatedConsumer products (40 CFR 59, Subpt. C) State This product is regulated as a Cutting or Tapping Oil (non-aerosol). This product is compliant for use in all 50 states. Local restriction: This product cannot be used in the South Coast Air Quality Management District of California. Consumer products VOC content (CA) 2.9 % VOC content (OTC) 2.9 % International Inventories Country(s) or region Inventory name On inventory (yes/no)* YesAustralia Australian Inventory of Chemical Substances (AICS) YesCanada Domestic Substances List (DSL) NoCanada Non-Domestic Substances List (NDSL) 6 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US Country(s) or region Inventory name On inventory (yes/no)* YesChina Inventory of Existing Chemical Substances in China (IECSC) YesEurope European Inventory of Existing Commercial Chemical Substances (EINECS) NoEurope European List of Notified Chemical Substances (ELINCS) NoJapan Inventory of Existing and New Chemical Substances (ENCS) YesKorea Existing Chemicals List (ECL) YesNew Zealand New Zealand Inventory YesPhilippines Philippine Inventory of Chemicals and Chemical Substances (PICCS) YesUnited States & Puerto Rico Toxic Substances Control Act (TSCA) Inventory *A "Yes" indicates that all components of this product comply with the inventory requirements administered by the governing country(s) A "No" indicates that one or more components of the product are not listed or exempt from listing on the inventory administered by the governing country(s). 16. Other information, including date of preparation or last revision 10-28-2015Issue date 01-27-2016Revision date Allison ChoPrepared by Version # 02 Not available.Further information Health: 1 Flammability: 1 Physical hazard: 0 Personal protection: B HMIS? ratings Health: 1 Flammability: 1 Instability: 0 NFPA ratings NFPA ratings 01 1 The information contained in this document applies to this specific material as supplied. It may not be valid for this material if it is used in combination with any other materials. This information is accurate to the best of CRC Industries' knowledge or obtained from sources believed by CRC to be accurate. Before using any product, read all warnings and directions on the label. For further clarification of any information contained on this (M)SDS consult your supervisor, a health & safety professional, or CRC Industries. Disclaimer 7 / 7 Material name: Honing & Cutting Oil SL2523 Version #: 02 Revision date: 01-27-2016 Issue date: 10-28-2015 SDS US